Turn Signal/Running Light Bulb Replace | Jeep Patriot | 2007-2017 | Nothing is easy to fix on a JEEP

This video will show you the process #MundaneMan went through to change the front turn signal/running light bulb on my 2010 #JEEP Patriot. I believe this process will be the same for years 2007 to 2017 for the the left and right side.
Replacement bulb used is a #Sylvania 3757KA (Amber Color)
Music by Epidemic Sound (www.epidemicsound.com)
Disclaimer: This video is intended for entertainment purposes only. I am not a professional automotive technician and the content herein describes my methods for completing this task. It is not a step-by-step process. Consult with a certified technician for professional advice as required.

[@joelparetas3107]

Thank God for KZbin on for people like you much appreciated. doing this on my daughters patriot. What a PIA.

[@ronaldsinagra8825]

Thanks for doing the hard work of figuring out how to do this, and sharing it with the rest of us Patriot owners. The manufacturers make what should be simple jobs difficult so we have to go to a dealer and pay astronomical prices for a simple bulb change.

[@mundaneman254]

Glad to help

[@michaelanctil5475]

Thanks for the helpful video. I went to change out the same bulb in my wife's car and was dumbfounded with how they designed this. I figured those panels had to come off to access the bulb. You did a great job walking through the process. Thanks again, have a blessed day.

[@jackielowrey3032]

2012 Jeep Patriot front blinker went out suddenly. I wish there was a dash warning before you get the hyper speed blinker click letting you know its dead. I was able to change my rear blinker months ago so i think i can try this out. Found your video easily after searching"changing front blinker on jeep patriot" saw you posted 2 years ago and people are still getting help from it. thanks for posting!

[@Oofadog1]

FYI, everyone has leftover bulb grease from those packets they sell you when you buy the bulbs. I use the extra generously around the socket to make the installation go easier. It may even help to keep water/dirt out of the area. Hope this helps.

[@thomashatton5633]

Thanks from the UK in 2020 for this, saved me a lot of time. Bless you Sir

[@jrctneon1964]

THANK YOU!!!! I have never been so confused tryin to change a bulb before!

[@shilohpuppy5649]

Just finished the process of changing my wifes bulb on her jeep. Thank you SOOOOO much for the tutorial video!

[@ritawoods2957]

They didn’t take the front panel off to change my turn signal. I don’t understand

[@glennkrieger]

You seriously made this job much easier. After buying a 2011 Jeep Patriot the right bulb (not the left) went out 3 days later. Arrrrgggghhhh. Thank you so much for the detailed instructions and the "watch out for" comments.

[@98Realm]

This video was incredibly helpful! Keep em coming!

[@oursin777]

Man, I can't thank you enough for this vid!

[@sublimemugs]

I was so close to prying the fixture out with a screwdriver (looking at the scratches below the lense, that is what the previous owner tried) Thanks a lot for posting this video.

[@exploringwithmrnobody8784]

Thank you for the info on changing the turn signal bulb on my 2014 Jeep Patriot. Like you said it wasn't easy but the job had to be done. I had a lot of condensation inside the lens so I got a lot of it out with my compressor. Thank you for the video it was real helpful and I subscribed to your channel.

[@blinderII]

Great video...well done! Back light bulbs MUCH easier to change.

[@montydaniels1054]

Thought I'd try reaching the bulb from the engine compartment & noticed the bulb was already out of the rear of the lens. I moved it & the bulb started working. I'll take the piece off from inside the wheel well today & get it back in. Thanks for the video upload. All the questions are now solved, lol what an idiot way to make bulb replacing so hard. Thx Chrysler......

[@lindzylou1690]

Thank you for this step by step easy to follow video! Much appreciated. My grandma has needed her blinker bulb changed and nobody can figure it out on her Jeep, as it's much different than any of our cars. 😊

[@rs3117]

Thanks for the video it really helped. Only thing I had to do different was to pull back the wheel well even further and get to the bulb from the top instead of the bottom. I could not get my big hands in far enough from the bottom. Thank you!

[@gunnerrunner1498]

Thank you I'm at Walmart and it is almost dark 6:50pm about well already done putting in a light bulb 💡 that was a tight space to put my hand through lol. But it's done.. thanks again man 👍

[@inspectorsteve2287]

Just to let you know those tabs have a round piece in the middle you pull out first. Then the rest of the tab will pull out easier without breaking. Thanks for the video. It was very helpful.

[@richardfresorgerjr.6806]

They make a tool to remove them too

[@churchgest]

I'm excited to do this, thank you for the information

[@mitchw.3220]

Thank you so much. Very easy to follow and simple words. U are awesome

[@itzness416]

Thank you for this informative video. This is going to help me out so much.

[@melodydelgado8306]

Thanks for your wonderful video. You saved me a lot of money!

[@tippygirl10]

I admit defeat, I light bulb is glued in there and I can’t get a grip to twist it.

[@littlebrainbighead]

Helped me on two diff occasions. Thanks!

[@williamdyckman9704]

Have to change one today, thanks for the information!

[@mariofuentes3429]

Just the video I was looking for !

[@Calichick310]

Thank you! I think even I can try it and I'm 7month & 1/2 pregnant! Haha. Thanks for explaining step by step!

[@RodeoCowgirl-55]

Thanks so much. I now know what to do as my bulb burned out. Thanks a million.

[@traviscooper2205]

Very helpful. Thanks. Wish it was as easy as the rear lights.

[@borisalvarado1866]

For those with weak grip or a stubborn light assembly that won’t twist out; try using an adjustable wrench to get around the assembly. I had to cock the wrench a slight bit but it got on enough to loosen the assembly. Careful not to wrench too hard on it or, whole thing is plastic and not made to take abuse.

[@SabotLoneWolf]

Awesome video!!!

[@filmic1]

Thanks Tom! I have a 2008 Patriot North. My front right turn signal just went.

[@filmic1]

Tom, are there pinch pins on the sides of the bulb socket that have to be squeezed/pinched in to turn the socket? It just won't move. Budges a bit, but won't twist out. Thanks for any insight...

[@GreenMyce]

Just finished this hell. My arms look like the family cat and a rose bush had a tug-of-war. Tightening the housing clockwise on the driver’s side was the worst. I recommend trying to get two hands in there if you can. Next time I’m taking it to the shop. Never buying a jeep or any car with plastic rivets again. Thanks for the video.

[@mattbird8728]

Just watching, it seems like it may be easier if turned the wheel to the left. Thanks for the video

[@carolekiernan296]

Perfect directions!

[@philipwysocki9288]

Just bought a 2010 Jeep Patriot, and it has a running light out. Thanks for the video!!

[@deansibthorpe6758]

Brilliant! Thanks, Tom!

[@dmzabo3914]

Obviously I have the same situation (same side) ... my question is why couldn’t they just have that turn signal panel fixture pop out? Like you just said. My goodness they do things completely reverse to reality. I swear the manufactures are not bright! Thanks for the How to video. Looks like I’m going to need it. Love my Patriot but just not these issues .

[@ToyotaSubieDude]

They do it so that you have to bring your car into the shop. That’s why I prefer older cars

[@maryarmstrong5803]

I replaced the assembly for my blinker light last year and the hardest part was getting the fender well open with those clips. I have to replace the one on the opposite side now, and I was hoping there was another way.

[@joelgranados3754]

Yea I just got one bot to long ago had many problems but runs like a dream now

[@zachholland7821]

This was really well done, thanks! I’ve got that same issue and wow, is it frustrating! I’m having trouble getting the panel to fit back properly, it seems like the holes and riveya on the bottom won’t line up. Did you run into any issues with that? Or did it slide back into place fairly easily?

[@davidt.5744]

Got it. Thanks a lot!

[@ricklambert9012]

Great job “

[@duncanjosh001]

Well done

[@WEBJR1977]

Thank you that helped me of alot

[@ging011gc]

Thank you!!!

[@Blakklansman254]

Thanks bro.

[@paulinasainz113]

Do you have any suggestions on how to remove the bulb that is stuck ?

[@timschubert5850]

3:30 there is a bolt right above this left middle finger......simply unbolt that one.....the whole panel slides open and you can easily access the light...your welcome...

[@shannonfake9893]

where did you find the two replacement plastic rivets?

[@tcmusic_thomas_upton]

If you carefully pull downward on the center of the plastic clips, they are re-usable. Also, if you do not have a 7mm socket, an 11/32" works OK..... I pulled off the wheel, and was able to get more room to pull back the inner fender skirt a bit more. Then, after rotating the socket loose, I could bring the entire assembly out to work on it.

[@ryantaylor4196]

It’s so funny my right side went off just like exactly in the video 😂😂wow

[@scottv8960]

Great video, hard to get to,

[@DEADLOK69]

Old car parts are very easy to remove and replace. But Removing a signal light on a Patriot: That was a struggle. It was hard to twist the socket back. And I had to scrape the entry points just to snug it back.

[@mutakasata6752]

Hi! Do you have any idea on the bulb socket for these bulbs? the socket is not staying attached to the harness!

[@Kerrsartisticgifts]

I had my right front signal light bulb changed. It turned out to be a short so it only worked for a second here and there. I saw the frayed wire when he was changing the bulb but he didn't have time to repair it. Now every light on my dash comes on and flashes, 4 wheel drive seems to actually kick in. Its the same year as yours but its a limited Any advice? Can I still drive it for now?

[@grasshopper732]

THANKS MAN

[@lavxll66]

dont gotta worry about that first step. bumper came off so that saves me time

[@mundaneman254]

Nothing like some "weight reduction" to make it easier to repair!

[@victoriapenalver4518]

How did you manage to turn it counterclockwise? Getting to that part was quick but after 2 people and 30 minutes of trying I gave up. Neither of us were able to get it to turn.

[@NaguWhiteout]

I got it out, but it seems the socket is broken. Can this socket be unmounted? It has a red sliding thingy but I cannot pull it appart.

[@mutakasata6752]

Thanks bud

[@lewiandrr64]

You da man!

[@billbolinger6453]

Good video. If you can get your hand up there, you have me beat. I had to remove the screw holding the corner of the very upper corner of the bumper in place (same as the three you just removed). At that point push the corner of the bumper forward, but only after putting a plastic pry tool in the space between the turn signal top and the body to keep the warped plastic there from hanging up as you push the bumper forward otherwise it will catch on the body and you can’t push the corner of the bumper forward. With the bumper forward, you have full access to the socket. And yes the turning of the socket is insanely difficult!!! Pliers, adjustable wrench, etc is likely your only choice. That said, I would suggest a bunch of blue tape to protect your paint in this process!!! Poor design for sure. The stealer-ship can eat my dirty shorts if they think I’m going to pay their rate for this one! But while you are at it and have the tools and the newly acquired knowledge, you might has well continuously cuss the jeep designers in the process and change the bulb on the other side. It’s just a matter of time before it goes as well.

[@donivan3863]

On my ‘08 Patriot those plastic fasteners on the bottom screw out. The middle part pulls out about a half inch then you have to turn them out the rest of the way! Could have been why yours broke coming out. On the one behind the wheel the middle part pulls straight out without any turning though, strange they couldn’t just use the same fastener all around

[@angelaelectronic9182]

The jeep knows when the lights going out and will click quickly as a warning. I changed the lights be its still clicking like its going out. Any idea how to reset that?

[@Onepersonsopinion]

Any one know the brand and model # of the replacement plastic rivets? I have been looking for those for my 2014 Jeep Patriot with no luck. The ones I found were too small. Thank you.

[@alexh4273]

thanks i went with led cause i don’t want to keep changing bulbs

[@tysonmarr9940]

Does this work on 2015 jeep patriots?

[@pauld7309]

I think the driver's side is tighter / harder to do!!

[@djanthaz]

Yeah I’m just trading it in

[@summertimelazlo]

Thank you for your video. I had to replace a broken light housing and not just the light. I found the exact same issue but made some executive decisions...(1) I released the 3 bolts and the plunger-rivets, (2) I CUT the panel at the crease so that I can see the 3 anchor screws on the light housing, (3) I used my drill with an 8" extension and my torx to remove the light housing, (4) I then replaced and reattached all the bolts for the wheel well and re-attached the 'cut' section with a zip tie. 10 minutes. Good luck

[@rfine93]

Agree on the engineers who made these piece of crap, the alternators are a blast to change also, never will buy another one of these.: (

[@Joshua-smith1989]

Question I got a jeep patriot 2011.. the turn signal work on the right front side but the running light won't... any answer to why? Please and thanks.

[@Joshua-smith1989]

No problem.. I figured it out, the socket wasn't staying on so I bought another socket and it fixed the problem.. btw good video!👍👍👍👍👍

[@greggkemp2903]

Nice job Ehh

[@notsohandytim5090]

And so now, that patriot will rattle on for the remainder of it's days, while the electrical circuits systematically stop functioning as they do in my 2013 Compass.

[@rdanielmerin1695]

This just happened to me , I replaced the bulb and the turning light works but the Run light doesn’t , do you know what might be the reason?

[@mundaneman254]

I could only suggest a bad bulb out of the package, bad socket or a wiring issue.

[@rdanielmerin1695]

@@mundaneman254 thank you. it was a bad socket

[@josephpeck8723]

I started out clicking on another video about the same subject that didn't show how. The car salespersons will tell you people buying cars do not ask about fixing them.

[@trevorism100]

They only make it difficult so you take it into a certified dealer for repair

[@wandastevens3183]

I know why their so hard to get out ...so you'll have to go to a dealer and pay outrageous prices just for them to use their "specialized tool" to get them out and put another one in ...!!!

[@mundaneman254]

That seems to be their master plan.

[@petemartinez6717]

That is sooo much work to change a bulb, American engineering at its worst!!!!!!!!

[@1pyroace1]

Correction I think it’s 3157 if I’m not mistaken

[@donbelmont1125]

I believe 3157 is for the rear signal indicator

[@craighorner4607]

Considering the major design blunders the automotive industry has been forcing mechanical engineers to do, I wouldn't be shocked if a federal serviceability requirement would be next just to force the industry to stop the majorly idiotic mistakes they have been making

[@johnrich312]

Lmao guess I’m goin without a left turn signal for a while

[@LITMOVIESCENES]

i been without for months bc of this lol..im not paying a shop for this lol

[@stevejohnson1397]

My wife owns a 2009 has to be one the biggest pieces of s*** that I've ever worked on

[@mundaneman254]

Somethings are hard to work on for sure. From a reliability perspective though I am happy with the Patriot. I did a review of long term ownership at kzbin.info/www/bejne/jZjXYYNsob2No7s

[@LITMOVIESCENES]

@@mundaneman254 I have a stick..its the way to go with these from what i hear

[@williamconnor3988]

Just get on with it, instead of wasting my data. Took you a minute and a half to get started!

[@mundaneman254]

I have been accused of being too verbose. I am working on that. Thanks for watching anyway.

[@matthewwoods366]

Really appreciate the video, thanks. Still wanna kill myself because I'm gonna have to do both sides because former owner put in white led lights so you can't tell the turn signal is on. Tired of getting flipped off because people can't see my front signals and don't want my wife being harassed or worse.

[@DethPrufe]

Nah this didn't work for me at all. I went to another vid and it was super simple. This vid in particular was unnecessarily hard

[@LITMOVIESCENES]

whata pain in the ass these jeeps are with the lights...ive never had so many die its unreal

[@Its303AcidBass]

Hard as f*** to turn it counter clockwise. This is bullshit!

[@TEAMCREAM_96]

Sorry excuse for a jeep

[@user-ot9fr6dk2c]

Possible the worst demonstration video of all time