Turtlebeach velocity one yoke binding fix

!!!!!!PLEASE FOLOW THIS LINK FOR AN UPDATED VIDEO!!!!!
• Turtlebeach velocity o...
tutorial to install and assemble the Turtlebeach velocity one yoke binding fix
etsy link:
vandijkstuff.e...

[@jhrober357]

I've been using this solution for a couple of weeks. It absolutely helps smooth the elevator action on the Velocity One yoke. Nicely made and simple to install. Great product. I bet TB has been looking at this.

[@JoelFinkel]

Your design is exactly what TB should be offering to their customers. After using the yoke for 30 seconds, it is obvious that it needs a proximal bearing. Nice job. As I don't have a 3D printer, I would be happy to purchase a physical product and hope you can make another batch soon! I'm sure they sell out quickly!

[@user-jr6bi7ly6s]

Hello Kevin. Your fix is absolutely fantastic. I received it about 3 days ago and have been trying various tightening's and have now found the sweet spot setting you mention. Thank you so much for this fix. I was getting very frustrated with the yoke's excessive stickiness. The fix has resolved the problem massively. Thank you again .

[@user-jc5uf7nh5z]

I bought one which arrived today 05-06-24. So easy to put together and fitted it onto my yoke this afternoon. Works really well exactly as Kevin described. Thank Kevin for such a simple solution.

[@MarcoCantieni]

I just have received the finished part from Etsy. I've installed it and had tighten it too much. The result was disatisifying. After watching this video and understanding how important it is to find the correct tightness of the screws it runs on butter. I'm happy now Thanks for your excellent work!

[@theherbalist1978]

Got it today, installed it easily and it works great. And for the throttles I recommend using some ice cream sticks, which you can easily make little thicker with electrical tape (if needed). And you just slide them in the throttle body just a little bit, along the throttle arm, and finally you tape the stick and throttle arm together.

[@pi.actual]

I made a similar fix using a worm clamp and two spring loaded screen door rollers. It works. Turtle Beach needs to step up, acknowledge the issue and at least provide a remedy source. This simple device that Kevin has come up with would solve the problem at very low cost because, aside from this issue the Velocity One is a very good product.

[@Sammys-cf7hw]

Can you make a tutorial on that ?

[@tomjanzen9278]

This thing really works! I still can't land worth a damn but it's no longer the fault of the V1F.

[@dangreen5456]

What a delight to find such a well engineered product at such a reasonable price. Follow the steps in the videos works perfectly. You will appreciate the difference this makes.

[@johnnicolucci380]

Good Day, Kevin. I just got mine. I am in Toronto, Canada. It took a few weeks to get here. Thank you for including more pins. I broke one - it is a very tight fit. Everything else went well. Works like a charm. Thank you again - well thought out, excellent design and very clear instructions on how to install.

[@donl5888]

Just got my kit today and it works exactly as designed. Smooth as butter now. Excellent work Kevin!

[@LieneCambridge-ib7tx]

Fitted mine last night absolutely brilliant well happy thanks Kevin 👍🏻

[@RickHale]

I got this today and installed it and it makes my yoke so much smoother.

[@RJStylee]

glad i found this video. I have been lifting the yoke to move it for small corrections to reduce the drag and stickiness. i assume that this roller system lifts it for your while creating a support. just ordered it.

[@jepley929]

Just received mine today. Assembly was simple and it works perfect. Thank you!

[@patrickcallaghan8326]

Just got mine. Works great. Thank you.

[@dougrash2330]

Bought STL files last night--Did not have PETG filament so printed in PLA Plus--had everything else so put it togather and installed--It is very effective at reducing the yoke stick dramatically..................any one thinking about buying it just buy it--as they say--DON'T THINK--DO---you will be very happy with the improvement--printed easy in PLA and I got some PETG today and that printed just as easly--it is everything promised in the video--WOW and Thanks

[@franciscofortuna3562]

Just bought it on Etsy. I hope it arrives soon!

[@Ezza-1]

Just fitted this to my yoke. Works like a dream. Very well designed and fits perfectly. Well done Kevin.👍 15.10

[@kevinvandijk86]

I wish you lots of fun with it 👍

[@kevinvandijk86]

I would like to see a review on fb, I'm planning to make more, you could help me a lot to make people aware.

[@tysell6206]

Hello Kevin. The kit finally was delivered to Colorado! Thanks for creating this device and video. It makes my V1 much better. By the way, I think your English is very good!

[@kevinvandijk86]

Thanks, so kindly of you!

[@kevinvandijk86]

I would like to see a review on fb, I'm planning to make more, you could help me a lot to make people aware.

[@tysell6206]

@@kevinvandijk86 done…

[@acelear]

Thanks to your great video Kevin, my installation was flawless. It works perfectly!

[@alessandro.baldini-zf2xj]

Just got it. Installed it. What a relief! Thanks a lot!

[@kevinvandijk86]

So many people asked me to make more of my binding fixers, so I did! 🤩 After a very long print marathon I managed to make a batch of 50, the biggest batch yet! Available now on etsy! www.etsy.com/nl/listing/1533234581/velocity-one-binding-fixers-physical

[@rjc0234]

And they are all already gone :D must be a much sought after design. I think I will get the STL version, as I am lucky enough to have a 3D printer.

[@Louis_Roper]

I hope you are making good money! The design is very good.

[@aprilmc9768]

Thank you! I just ordered mine! Shout out to Huddison for getting the word out about this product! I never would have found it if not for him.

[@gregcharles7431]

Thank you, Kevin! Bedankt! It's really make a difference.

[@JM1701ABCD]

I wish I could still buy this...

[@kevinvandijk86]

vandijkstuff.etsy.com/nl/listing/1533234581/velocity-one-binding-fixer-v30-fysiek

[@Koriander93]

Hi Kevin. Would love to order one from you because I dont own a 3D printer. Do you plan a new round of orders? Cheers.

[@hoschie2261]

Hi, how to oder pre-made fixers. I do not have a 3-D printer nor the additional parts needed.

[@kevinvandijk86]

vandijkstuff.etsy.com/nl/listing/1533234581/velocity-one-binding-fixer-v30-fysiek

[@LaddoDoko]

Hello, I made a purchase on Etsy thinking it was for an actual pre-made bracket. Do you make them and post them to people? I've just purchased one of the yokes and saw your KZbin video. I would very much like one but don't have a 3D printer. Any help is appreciated, thank you.

[@dlink7277]

Just saw this and seems like a must have for the sticky pitch. I don’t have a printer. Do you plan to make another batch anytime soon?

[@kevinvandijk86]

they are available!

[@dlink7277]

Thank you! Just ordered one!

[@ozznomad1467]

Hi Kevin, just discovered this, but sold out on you link below, it looks great, are you planning another batch?

[@kevinvandijk86]

Probably

[@augustinandre-fouet8548]

Hello, than you so much, possible to make more ?

[@kevinvandijk86]

vandijkstuff.etsy.com/nl/listing/1533234581/velocity-one-binding-fixer-v30-fysiek

[@TsvetanVR]

You'd be wise to put the STL for sale as well, like most other creators within the 3d printing community. I, for example, would not pay 11 euros shipping on top of the asking price of something that I can 3d print myself, perhaps with even better quality. It's also a relatively simple design, easy to make from scratch but I probably wouldn't bother if I could buy something already tested and just print it.

[@kevinvandijk86]

Maybe I will, but there are a lot of people that don't have a printer, and I don't want someone using my stl to resell it to make a profit. What would you pay for the stl if I might ask?

[@kevinvandijk86]

www.etsy.com/nl/listing/1429175008/stl-only-yoke-binding-fix-voor

[@freedom2ignite]

@@kevinvandijk86does the stl file also come with a shopping list of the other times needed to fit this stl? And do you know if they are available in the unities states?

[@LesGainous]

@TsvetanVR, you are paying for the inventor’s hard work, design, and testing. Why would he give up the secrets to it?

[@landonnnlandonnn7302]

I’d love to buy one but have no access to a 3d printer, any word on when you might restock?

[@kevinvandijk86]

Only a few left! www.etsy.com/nl/shop/vanDIJKstuff

[@keythbryant4226]

American here. Hi! Nice job! I would also like to get one but I can't read your language or understand the product page.

[@StevenNovak]

I want one!

[@kevinvandijk86]

vandijkstuff.etsy.com/nl/listing/1533234581/velocity-one-binding-fixer-v30-fysiek

[@Peter-po3nd]

Great job😅

[@maxxonline2001]

Thank You!!!!!

[@KingBobsKingdom]

Any plans to make more of these? I would like to purchase one.

[@kevinvandijk86]

I'm on it!

[@eddthirty4065]

Hi Kevin, are you going to make any more?

[@kevinvandijk86]

they are available!

[@kevinvandijk86]

They are available again ❤

[@leoschlatker3047]

Already gone :(. Are there more comming?

[@kevinvandijk86]

@leoschlatker3047 yes!

[@Dexadrinne]

I am about to order from Etsy. Question. What type of bearings are being used?

[@TheMightyBanana6668]

Will you be making more?

[@kevinvandijk86]

they are available!

[@rickhilton9108]

Do you ship to the USA? Thanks I'm in need of this product

[@kevinvandijk86]

Yes

[@holgerfries7607]

Hello Kevin, how can I buy it?

[@TeKieler72]

Hi! Great work! How can I order one, it is sold out on Etsy. 😢 Thanks and best regards!

[@kevinvandijk86]

they are available!

[@bengvideos572]

It's sticking badly

[@plavnyphotography9871]

will you be making another round

[@kevinvandijk86]

I'm on it! 😎

[@Louis_Roper]

can i buy it as the actual product not the plans?

[@kevinvandijk86]

vandijkstuff.etsy.com/nl/listing/1533234581/velocity-one-binding-fixer-v30-fysiek

[@Ines-Manel]

Are there more comming?

[@kevinvandijk86]

vandijkstuff.etsy.com/nl/listing/1533234581/velocity-one-binding-fixer-v30-fysiek

[@grizzlytasbear9716]

I used dw40 on mine the other day niw im watching this video and feel a f#$king idiot lol

[@Louis_Roper]

me to 🤧

[@KAPAFlyer]

Are you using Racing Pedals on Xbox on Flight Sim?

[@kevinvandijk86]

no this was just for displaying purpose, it is a race stand.

[@markmansingh1750]

Hi, I've gone to your ebay link to try and buy it but I think I'm unable to. The page is in another language so I could be wrong but I don't see a buy button. I would appreciate your assistance as I would like to purchase your product. thank you.

[@kevinvandijk86]

You're right, it completely sold out unfortunately, next month there will be more 😊👍

[@markmansingh1750]

@@kevinvandijk86 ok thank you, do you know exactly when next month? Just so that I could look out for it and get one before it sells out again. :)

[@kevinvandijk86]

Sorry I can't, but I post it on Facebook 2 days before you can order. That makes it fair 👌

[@markmansingh1750]

@@kevinvandijk86 thanks :)

[@kevinvandijk86]

Good news!!! I finally have all the parts together for another batch of velocity one binding fixers! To make it fair for everyone, I decided to put them to sale on Sunday 26th of February at 20:00 GMT. Keep an eye out on the Facebook groups, I will post the link there on Sunday! Be sure to get one, they will be gone fast!

[@lightgeiz9617]

What is your Facebook and how can I order

[@kevinvandijk86]

Good news for everybody who missed out the last time, I just finished the 4th batch of 30 V1 binding fixers. They are available on Sunday 19th of march at 8:00pm GMT. So please set your alarm clock. You can find them on etsy in my shop vanDIJKstuff! www.etsy.com/nl/shop/vanDIJKstuff