How to apply wrinkle finish paint VHT Wrinkle Plus FAQ Instructions valve covers header tanks

A simple guide on how to refresh worn looking items using wrinkle paint

[@kdash3215]

Thanks, I got an excellent finish with your technique. Cool thing is you can spot treat if you missed an area or if it's not built up enough. It's hard to mess this up.

[@tweedbean]

Great tip!

[@noobmcgoob9745]

Brilliant video! I tried and failed to get a decent wrinkled finish until I used your technique!

[@tweedbean]

Thanks for watching

[@ForestWoodworks]

This was totally awesome 💯. Thanks for the concise tutorial. I may have the confidence to try this on my Walker-Turner Driver Line ac motor restoration end bells tonight 🔥

[@tweedbean]

Good luck, thanks for watching

[@bradypellarin8573]

Nice video, good clear directions for use.

[@tweedbean]

Thanks for watching

[@sethtaylor5938]

I use a zinc chromate yellow or green primer on aluminum. I’ve had some paint adhesion fails without primer. Electrostatic painting in the factory overcomes the adhesion issue. However, at home painting in my opinion needs primer on any bare metal, even sprays that claim you don’t need primer. Also I’d use a mild lye caustic soda bath on aluminum before any painting in addition to degreaser. And of course wash off any prep solution. Wear nitrile gloves and wear safety glasses.

[@tweedbean]

Thanks great tips

[@sethtaylor5938]

If use water a weak Draino solution for cleaning aluminum with distilled water. They sell it in the grocery store (about a dollar for one gallon). About 1/2 teaspoon of Draino in a 1/2 gallon is enough. I'd let the lye solution work for about a minute. Use distilled water to wash off any residue. Use nitrile or kitchen latex gloves and safety glasses.

[@jcgonza2664]

Good tutorial ❤️👌

[@tweedbean]

Thank you

[@estuardo1631]

Thank U

[@tweedbean]

You're welcome 😊

[@mJlReplicanT001]

Hi ya .. does that tank work on the Manuel R56 coopers, I have seen some that won’t work due to the bottom coolant line is too far forward and fowls on the gearbox linkages .. Awesome videos , following you. Been heaps of help . Thanks again

[@tweedbean]

Myki Jay thanks I here if your not careful with the lower pipe it fowls however apparently with careful placement of the lower pipe it’s fine. Will do a fitting video

[@mJlReplicanT001]

tweedbean champion ! Interesting to see, definitely need a change from the old standard plastic bottle it has! Doing solid work, cheers again

[@user-pwfus]

If you want the best wrinkle affect use an oven set it at 170f and be amazed

[@tweedbean]

Great tip thanks

[@sethtaylor5938]

I do 180 because that’s lowest setting on my GE oven. I do 15 minutes bake in convection mode that gets even heat. Beautiful hard finish!

[@markhammari5832]

If you suspend your part on a wire you can spray the bottom as well at the same time.

[@tweedbean]

great tip

[@Chicitypo]

Just stumbled across this video. Great detail in your video. How has this held up? Is it scratch resistant when dry?

[@tweedbean]

Hi thanks for watching, still like new. Its pretty hard wearing, I wouldnt say scratch resistant but seems stronger than matt paint for example

[@Cgtlfa]

Always wondered is it best to remove the masking tape before it dries? Thanks for the video btw

[@tweedbean]

I’m not expert but I would probably say yes to avoid peeling the paint but that’s just my opinion

[@rhbb228]

Can i use it over something thats has primer on? Or can i also spray it on something thats painted?

[@tweedbean]

Best refer to manufacturers guidance on those questions. Thanks for watching

[@jeffruebens8355]

It is better to wear gloves- skin has a lot of oils that cause fingerprints. I used the wrinkle black in 1978, after a friend hit the plastic gill-shaped front grill for my 1972 Plymouth Barracuda to help hide the crack after I glued it back together. I have seen people use an outdoor gas grill to cure paint. The wife will probably be upset if you use her oven.

[@tweedbean]

Great tip

[@vgabrieloklr1374]

Hi man! Can i paint the bumpers of my truck with that vht paint?

[@tweedbean]

Thanks for the question, are they plastic or metal?

[@vgabrieloklr1374]

@@tweedbean metal!

[@dha588]

Do you need to apply clear coat?

[@tweedbean]

Hi thanks for watching. This product doesn’t require clear coat

[@matt7sixty]

In direct sun light only or Can this technique be done in garage and then heat gun? Thx

[@tweedbean]

Garage and heat gun 👍🏼

[@matt7sixty]

@@tweedbean Thx! Trying now

[@joseribera6800]

You think I can paint my steel braided hoses with this. They are chrome now and would like them black

[@tweedbean]

Assume your hoses are flexible so this wouldn’t work. Maybe some sort of rubber paint is what you need

[@joseribera6800]

@@tweedbean ok thanks

[@nilesminor7403]

Whats your thoughts on doing this to the gas tank?

[@tweedbean]

Can't see why it wouldn't work

[@adamearle583]

“Wipe it down with grease remover to get rid of any oils or grease” as he grabs it with bare hands. 90% of the time it’s fine but put a set of gloves on to save the headache the other 10%

[@tweedbean]

Great tip, one for the future for sure

[@TrashTakeCallouts]

How long did you wait after your final coat before using the heat gun?

[@tweedbean]

No more than 5 mins

[@Jeepdriver75]

Durability good?

[@tweedbean]

Seems to be yes 👍🏼

[@richardstephenson1266]

I have to say I bought this product for my harley engine on the strength of your video. And now I have to strip the while lot off and start again. Probably something I did bit I found it total rubbish.

[@tweedbean]

Sorry to hear that. I’ve done a few pieces now with it and had no issues.

[@austinlane5533]

@A. Melbs Probably something in the preparation department. I've used it on 2 HD engines. One with great success after a thorough cleaning and I got cocky a second time and blasted it on with poor results.