Twine feed on small square baler-How to

This video is showing how you connect twine from bale to knotter disc.
First you put twine bales in the bale chamber. You will need to put at least 2 or 4 bale of twine. Then you need to guide the twine from the bale through the twine tension system, down through plastic rings and through the needle and up to the hay chamber.
Now you start up your tractor any engage PTO to turn the baler and you hold the two ends of twine together, you spin the wheel to engage the needles and then the needles go up to the knotter disc and twine catch itself to the disc and the baler is now ready to do some hay bales!
If you like the video please give a thumb up,
Subscribe to my channel and don’t miss other new repairing and farming videos that I will upload in the future.
Subscribe to my channel Mark the farmer here:
/ @markthefarmer
If you need you can order baler twine here:
amzn.to/2Yr6gbh
#Markthefarmer #how to #feedtwine
#haybale #reparing #twine #hay #twinefeed

[@markthefarmer]

If you like the video please give a thumb up, Subscribe to my channel and don’t miss other new repairing and farming videos that I will upload in the future. Subscribe to my channel Mark the farmer here: kzbin.info/door/piqU7ikeaIBfWSa0itwcdQ

[@briandonovan8455]

Hi Mark Thankyou for your videos. I bought recently an 46 baler and it is old but it works. Your videos have shown me how to fix it up and made me get some parts from UK to do some renovations on it.

[@markthefarmer]

@@briandonovan8455 Awesome. I am glad my videos helped you. Keep watching the channel.

[@mihai-reluivanescu6270]

Thank you

[@ng3038]

Had to do knotters on my MF baler after watching this video I'm back up and running, thanks

[@markthefarmer]

You're welcome, happy that my video helped you 👍

[@ng3038]

@@markthefarmer it helped a lot, greeting from Ireland

[@RJ-yz6pm]

Great video! Really helpfull

[@markthefarmer]

Have a good work hay seson is just starting up.. happy that it helped you!

[@mattmar5162]

Nice! Locations on other models for twine paths may differ slightly but this guy nailed how to retwine a square baler.

[@markthefarmer]

Thanks you are welcome Mark

[@MichaelYuhas]

Thanks for the video. I have an IH 425 baler and it's similar. I have to thread the needle on one side as it pulled out when twine got tangled in the twine chamber.

[@markthefarmer]

Maybe you rotat the empty baler by hand and you might see wher is the problem ?

[@djsimonrossprice9400]

Great video. Plus your English is excellent my friend..👍👍

[@markthefarmer]

Thanks! Have a nice day

[@shaynevaughn3164]

Thanks for the video, using an old international baler in northwest Arkansas

[@markthefarmer]

Your welcome

[@multivuksan]

Thank you, your video helped me alot.

[@markthefarmer]

You are welcome

[@gustavoesteves7076]

Obrigado! Estava atrás de um vídeo desse.

[@reesvalleyranch3933]

Video helped me a lot

[@JGPT1681]

Thank you!

[@sheldon6993]

That helped heaps cheers.

[@markthefarmer]

Your welcome 👍

[@rawazhamaali8825]

thanks mate

[@ioanalexandrudragusin3222]

How do I thight the shuttle? Is slipping out from shuttle... please help

[@richardvermeulen3123]

You made an excellent video Mark. It really helped me. Do I have to cut off the excess rope end?

[@markthefarmer]

Thanks for comment, Happy to help! Yes you can cut it but not too close to discs 🤘

[@lazio7495]

Great video. Is that an International 434 baler?

[@markthefarmer]

Its international mccornick B46

[@williamchristopher1560]

Great vid. Helped me understand how to do it. What make and model baler is that?

[@markthefarmer]

William you are welcome Its mccormick international B46 I sold it abolt year ago now i have smaller baler Lerda 1100

[@dermotned9697]

Great videos mark I just bought a b46 and was wondering did you have to change much to use plastic twine mine is on old twine

[@markthefarmer]

Thanks for the comment Dermot Ned. Do you think twine like mine ? Blue? You can make a knot betwen old and new twine and it will feed it self

[@dermotned9697]

@@markthefarmer thanks for your reply, I was told that these old baler wont work with plastic twine but I see yours works fine so I will try it

[@markthefarmer]

@@dermotned9697 Yes mine was working good mise one or two... make sure to have sharp knife ... or if you replace it with new one

[@williamchristopher1560]

How did you get the needles to back out far enough to put the thread through them??

[@markthefarmer]

You put it thru under the bailer

[@dimmytihon]

Hi Mark I've got the same baler and I've changed from sisal twaine to plastics and one end of the twaine is coming out from the disc and only one end of the twaine is getting knotted What can be the problem?

[@markthefarmer]

Is your disc damage is missing a pin on the end, cus mine was and i had to take the disc out and weld some metal up.... take a mesure from knife and disc and do with spect.. or take the mesure from the disc to knife that making knots and adjust the other one ... have a look to nidles as well if they are too worn out the twine cant come up to disc and disc canot take ... You can spin your baler by hand its a bit harder but you will see how it is working and where does it miss... Hope i help you

[@dimmytihon]

@@markthefarmer Thank you Regards Dimmy

[@glenparks5175]

I always just stuck mine thru needles then tied them off back to frame underneath, did the same thing I guess

[@taem111]

right saved a step

[@Mackeson3]

Yeah, no need to pass the twine into the bale chamber, just tie the ends of the twines to somewhere underneath on the baler frame. When you trip the knotters the needles will bring the twine up into the chamber and then into the retainers 😉

[@higiniobarrero5689]

Porque me dobla las avujas

[@markthefarmer]

More info please

[@manlook5890]

Please i need translation into Arabic

[@markthefarmer]

Hi thanks there, but I don't know Arabic...

[@rahmanm4512]

Number plz

[@user-uq1bh7ho8b]

Thank you

[@ThePikeywayne]

Thank you