Ultimate Guide to ISTA+ Download for BMWs: Reset Tcase Adaptations Easily!

Enet cable: amzn.to/3KKFWyw
In this tutorial, learn the step-by-step process to download and install ISTA+ software on your computer to easily reset Tcase adaptations on BMW vehicles. ISTA+ is a powerful diagnostic tool used by professionals and enthusiasts alike, providing comprehensive capabilities for BMW diagnostics and maintenance. Whether you're a beginner or an experienced DIYer, this guide will help you navigate the installation process smoothly, ensuring you can efficiently reset Tcase adaptations and keep your BMW running optimally.
Enet cable: amzn.to/3KKFWyw
where to download ista:
www.bimmer-dia...
🔧 *Key Steps Covered:*
Downloading ISTA+ software
Installation guide for Windows
Connecting ISTA+ to your BMW
Resetting Tcase adaptations effortlessly
🎥 Watch this tutorial now to unlock the full potential of ISTA+ and maintain your BMW with confidence!
Don't forget to *like**, **subscribe**, and **hit the bell icon* for more helpful automotive tips and tutorials!
#BMW #ISTAplus #TcaseAdaptations #DIY #AutomotiveRepair #CarMaintenance #ISTADownload #BMWSoftware #DIYCarRepair #CarDiagnostics #BMWEnthusiast
Rear View Mirror: Wolfbox18%off : wolfbox.com/?r...
BMW Stereo: www.amazon.com...
EBAY 19T Turbos: ebay.us/QEJyae
Camera Used :amzn.to/3KO42ss
Amazon Store : www.amazon.com...
Rear View Mirror: Wolfbox18%off : wolfbox.com/?r...
As an eBay Partner, I may be compensated if you make a purchase

[@endriceka5266]

Excellent tutorial! keep the content for the G05 coming please!

[@jku392adventures]

Thank you! Will do! More to come 🤙🙏

[@robertgreatsinger9179]

Getting ready to do compression test, for Mom's 2008 N52 E60 528i. Needed ISTA for valvtronic adjustment to close valves.... Ordered K+dcam cord with usb other end... Payed $20.20 for ISTA.... Hope only battery charger on post is all else needed for proper ...

[@jku392adventures]

Hope you found my video useful, unfortunately I never had an opportunity to use ISTA with my e92 when doing major maintenance, but it is definitely nice for my g05 X5

[@rcruzthomas]

I would recommend a voltage stabilizer and not a battery charger. Voltage stabilizers can feed over 20 amps at 14 volts, whereas battery chargers provide a lot less amps.

[@jku392adventures]

@@rcruzthomas thanks for the advice, I tried looking for a voltage stabilizer, would you happen to have a link to one that you have? Or one that you would recommend that's not too expensive? Or are they all just expensive

[@emg2181]

Thanks for all the great info.

[@jku392adventures]

Absolutely, hope it helps! 🤙🙏

[@joez800]

Very helpful and thorough video. I have saved the video to my X5 repair library. I have 2020 X5 xdrive at 30K miles and plan to keep it for some time. Please keep sharing tips on yours 😊

[@jku392adventures]

Thank you for your comment! I like hearing that my videos are helpful, it definitely motivates me to make more 🤙🤙🙏🙏 And I do recommend doing the fluid ASAP, even at 30k miles. I heard bmw used the wrong fluid for the 19' and 20s'. Mite as well get ahead of it 🙏

[@nickbell3546]

Thank you for the tutorial!! I am looking into retrofitting a rear hitch with the active wiring -8SL option but see that the trailer control module needs programming to the car via the ISTA "Retrofits" path. Would you mind making a quick video showing what that looks like in ISTA?

[@jku392adventures]

Hey thanks for watching! Unfortunately I'm pretty new to using ista so I wouldn't be much assistance helping out with the trailer wiring. But best of luck to ya! 🙏🙏

[@PaulFlood-fw8tm]

Brilliant video. Please keep sharing tips. tks

[@jku392adventures]

Thank you! 🤙🔥

[@mileacostin6492]

Hello, do you know if this ista+ works on a g20 2021?

[@ackoeltechniek925]

thank you best explain

[@jku392adventures]

Thank you 🤙🙏

[@catalinbandas]

Very useful with many thanks.

[@jku392adventures]

Thank you! Glad you found it helpful! 🙏🤙

[@Legolas6911]

Very informative. Is it mandatory to reset the Transfer case adaptations or you can just only remove the old oil and top it up with new one?

[@jku392adventures]

Technically when exchanging the fluid on the transfer case, you need to have ISTA during this procedure because this will open up a chamber in the transfer case to allow all of the fluid to be emptied when doing this job, then it is also recommended to reset the adoptions. I would say if you're not going to do ISTA, I would still do the fluid exchange at the very least

[@simonpatcharinvenaglia7892]

@@jku392adventures Hi, is the transfer case the same for the 2008 X5 E70 HAVING THIS chamber divider?🤔

[@PaulFlood-fw8tm]

Are you going to change the fluids in your transmission and both differentials too? tks

[@jku392adventures]

Yeah I will be doing that someday, not for a little while though

[@simonpatcharinvenaglia7892]

I just did my diffs and transmission on my 2008 X5 3.0D E70. I'm just in middle of doing what's in this video. I'm trouble shooting the car will not go into gear. I've checked the transmission fluid level according to bmw instructions and it's all good. My next and hopefully last is to check to see if the trans electrical plug adaptor has been pouched home correctly, but I have to drop the pan again to do that, so hence why i'm getting ITSA and the K+DCAN USB Interface cable to just find out first if it could be a solenoid that was causing my original problem of gear box popping out of gear in high gears (5&6) while under acceleration load, (passing car or towing a trailer). If I have a solenoid gone I'll do the lot at same time. But hopefully it pick up on the plug adaptor if it's the no gears at all now problem after changing the trans fluid and as well I replaced the 5 other seals between the gearbox and mechatronic.😅😉

[@LilSezdi_Official]

does the ista also work in europe?

[@jku392adventures]

I would imagine so, not positive though

[@carlosgrajales5858]

Hi, it is asking me about the key and the license. I don't know if I did something wrong. I really appreciate your help. Thanks!

[@jku392adventures]

Hey I'm not too sure. I haven't had that issue

[@D.Schoenmakers]

In the video you seem to use the operating system Win 11, although Win 10 is recommended on the ista+ homepage. Is that correct and do you know of any problems under Win 11?

[@jku392adventures]

Yeah my laptop is Windows 11, and I haven't had any issues with it, works good for me

[@D.Schoenmakers]

thanks a lot...grettings from germany

[@jku392adventures]

@@D.Schoenmakers very awesome, we plan on visiting Germany soon in the next few years! Greetings from Arizona 🤙

[@D.Schoenmakers]

@@jku392adventures Sounds good! Let me know and we'll visit the "BMW World" in Munich together and I'll invite you for a beer😉!

[@bmwn5238]

did you need a license key from bimerdiagnostic?

[@jku392adventures]

@@bmwn5238 They email you all the information for downloading after purchasing 🙏🤙

[@bmwn5238]

@@jku392adventures yeah i got it last nigh i am trying to figure out why the program and softh ware up date for modules are not available in ista +

[@mayv2970]

How long did it take your one-click installer to finish installing? It's been like 2hrs and mine is still rolling

[@jku392adventures]

Probably only took about an hour to install, but that greatly depends on the speed of your computer. Were you able to finish the install and get it working?

[@Knox850]

Is there anyway to install ISTA on MacBook?

[@philippeagbozo5259]

You have to install a virtual machine I guess

[@keysersoze8247]

thx for your vidéo, I'm a French guy and I can take care my g05 m50D, can you add with ista the service date in the car ?

[@jku392adventures]

Your welcome! 🤙 And are you wondering if you can reset the service date with ista? Like the oil change date and stuff?

[@allanbruce9473]

all of the video is fine, but missing the most critical part: setting the COM port in the PC (the ISTA part is easy). The ethernet has to connect to COM1 and my laptop did not automatically "see" the ethernet connection - which under the IPV4 properties MUST BE SET to 169.254.1.1 and subnet mask of 255.255.0.0; so I have tried to create a "soft" COM1 part, but I still cannot complete identification on the Operations tab w/o getting the check cable or PAD error message. Ideas? Thanks!

[@jku392adventures]

Im sorry! I'm new to ista so it's all a learning process, but I am only using the enet cord so I did not have to do any of that extra stuff. It just connects automatically through obd to USB c. Wish I could help more but if you find the answer please reply so others can learn 🙏🙏🤙🤙

[@rcruzthomas]

Mine was plug and play with the wired ENET cable and the USB-C adaptor. connected to a Windows 11 PC.

[@jku392adventures]

@@rcruzthomas yeah it's definitely easier than I thought it would be 🤙

[@allanbruce9473]

​@@rcruzthomas In this very last release before BMW put in encrypted keys that no one but an authorized dealer had access to; they changed the software to the point where it would NOT work with all the flavors of Windows 10 - which is all that I could put on my Panasonic Toughbook C54 - which has only USB 2.0 or ethernet. Yes, I finally got it working but only with trial and error. At BMW dealerships/authorized, they have to but special dedicated BMW equipment to hook up to the BMW LAN/WAN. OTOH, some clever companies have hacked these machines and come out with there own $3K to $5K equipment - but I'm not convinced those are worth it for we private citizens. BMW has so many weird quirks anyway. For example, my front strut started to leak air AND THAT CAUSED the vehicle lock sensors to go crazy! Who knew? The same with the grill vent actuation motors. Yes, you can sometimes buy the actuators, but they will always fail. Why? Because BMW calibrates them ONLY within the grill assembly (I have two active air grills in the front) and the opening torque is a fraction of a Newton. The ISTA software cannot calibrate them. There is no hardware or tool to do it either. One has to spend $300 to $700 for each COMPLETE grill assembly rather than the $50 for just an actuator. But BMW will, as usual, tell you nothing but happy to sell the parts and blame the failure on YOU.

[@DannyKovalchuk-e9l]

how long did it take to receive the email with download links?

[@jku392adventures]

@@DannyKovalchuk-e9l took about 20 hours. But it was a weekend so that's probably why it took a while

[@DannyKovalchuk-e9l]

@@jku392adventures we have been waiting for over 36 hours now.

[@DannyKovalchuk-e9l]

do they have a support team we can reach?

[@izzy_c10]

Which interface do I select for e60 thank you if you could help thanks

[@jku392adventures]

The e60 is an E chassis so you need to download the other program for the E chassis

[@signupsignup1648]

Hallo, thank you for sharing this video. I’m trying to do the steps according to this video ( minutes 4:57-5:05). The windows shows a different menu. Any suggestions?

[@jku392adventures]

The screen will be a little bit different depending on what computer you have or your computer might not even require you to do that, is there something that looks similar to the box, select a similar option

[@mattymilan94]

Hi! Is the software also available in Italian?

[@jku392adventures]

Good question, but I'm not sure if the answer, im guessing it is not unfortunately. If you hear differently, let's us all know 🤙🙏

[@nottoday6212]

Hello I just bought ista package from that link and downloaded it and mail it says diagnosis and programing for f and g series and can you tell me how to do programing?

[@jku392adventures]

I havnt mastered programming yet, someday I'll make a video on it

[@ojpsw6667]

Once I pressed install it basically told be to do something with the ”global file” so I extracted that manually and then the program began extracting it too I think? Dont know if I did anything wrong

[@jku392adventures]

How did it turn out ?

[@Kevin01743]

My same

[@trojangpete8]

Does this work on Windows 11 Pro?

[@Lukensm85]

It did for me

[@jku392adventures]

Yes, it works for me also

[@jku392adventures]

Thanks for replying for me 🤙🤙🙏🙏

[@carcrazed1969]

How long did it take for your email to arrive?

[@jku392adventures]

@@carcrazed1969 took about 2 days for me, I think it's because it was a weekend

[@carcrazed1969]

​@jku392adventures Oh, okay, so I'll probably expect the same as I just purchased it. Thank you for letting me know! I'll wait and see.

[@jku392adventures]

@@carcrazed1969 yup! I got nervous and pretty impatient, but then it came 🤙

[@JWick813]

really think this transfer case issue is being over blown. but useful i plan on doing this soon.

[@jku392adventures]

I don't think it's overblown. I think people worry too much when the fix is decently easy. It will be over blown if they don't do the maintenance and end up having to replace it

[@jku392adventures]

But thank you! Glad you found the video helpful 🙏🙏🤙🤙 any questions you can reach out 🙏

[@emg2181]

Not overblown. I have exact same car, I recently hit 60k miles and it started shuttering when backing up, turning left or right, with harder gear changes.

[@JWick813]

@@emg2181 yea im a believer now i just had my TC serviced and it feels much smoother cornering at low speeds thought maybe it could have been the tires. Get your TC serviced guys!

[@jku392adventures]

@JWick813 hahaha glad to hear it's better! if you can, share my videos to anyone who needs to do this service. Thank you! 🤙🙏

[@vanaguilar9732]

Hi, I have a question, is there any way to change the language of Insta to Spanish?

[@jku392adventures]

I don't believe so, probably German and English only

[@flyingyakdeath]

what version are you selling?

[@jku392adventures]

@@flyingyakdeath I'm not the seller, I'm just a KZbinr who made a video showing how I downloaded it 🤙

[@flyingyakdeath]

@@jku392adventures well what version did you buy?

[@jku392adventures]

@@flyingyakdeath on the link that I put in the video description it should say which version they are selling, I'm not sure offhand which version I have, it should be the latest

[@zakriausman4627]

Hi I bought the software from your link and I didn’t get the link to download so what shall I do

[@jku392adventures]

@@zakriausman4627 how long have you waited for the email?

[@zakriausman4627]

@@jku392adventuresmore than 2 weeks😢

[@zakriausman4627]

I have all the payment screen shots and all

[@zakriausman4627]

@@jku392adventuresit had been more then 2 weeks

[@jku392adventures]

@@zakriausman4627 and you have not received an email? Check your spam and everything and let me know

[@Objectional_Opinion]

Just do ProTool?

[@jku392adventures]

Will protool do this? How is protool compared to Bimmercode? Or even bimmerlink

[@carcrazed1969]

Protools can't relearn the valvetronic, can it?

[@jku392adventures]

I havnt messed with protocols, I need to download it one day to play around

[@musastar10]

Why pay when ista is free plus i have newer one 4.50.10 newset version

[@jku392adventures]

@@musastar10 I made the video a few months ago, in sure they are already offering a newer version. And also I noted in the video that I originally did the free version, but that required me to pay for an online storage company so I could download the 200gb of data, and it still didn't work.

[@musastar10]

@@jku392adventures Tell me if you need the newest ISTA and new PSDZ data to

[@musastar10]

@ if you want new ista or psdz data tell me

[@kpkp7094]

@@musastar10 hey bro where did you download ISTA for free?

[@Mannymii]

@@musastar10I need it man

[@stevengasper7354]

I just bought the software and followed these steps, but ran into an issue! I go to open the software and it says “failed to start ISTA. Please make sure your ISTA configuration is valid. In doubt, reset any non standard ISTA configuration and reinstall ISTA” should I just try to reinstall or how would I correct this?

[@jku392adventures]

@@stevengasper7354 another viewer had commented with a similar issue, I believe he just reinstalled it and everything worked perfectly 🤙, let me know if that fixes it

[@stevengasper7354]

@@jku392adventuresso when I go to test the compatibility, it’s not the entire file itself that pops up as an option, but instead says “bmw coding tool” which I selected and now it’s reinstalling. Could that be causing the issue?

[@limaiemheykel]

For ISTA software is their website legit?

[@jku392adventures]

@@limaiemheykel it worked for me and many others with no issues but if you search hard enough the software can be found for free, it was just a hassle when I tried to do it

[@lalorios4226]

I can confirm it is legit

[@pavokx]

is this legit or a scam buying from that website? im curious

[@jku392adventures]

@@pavokx it worked for me, no issues that I can tell. Better than some random person on Facebook sending you a link for you to download stuff

[@sigcustomlures4777]

You can get it for free

[@pavokx]

@ where

[@chadriddle3517]

@@sigcustomlures4777where ?

[@andreiyuzlenko2046]

After purchasing and installing the program according to the instructions, I receive the following message when starting the program The database installed is not complete. A repair installation must be carried out. ISTA cannot be used without complete databases. The application will therefore be terminated Can you tell me how to set it up correctly? Thanks

[@jku392adventures]

I'm not 100% sure what the issue is, I would reach out to the company providing the program and see if they have any insight. Did you install exactly how i did? I know there some portion that some computers will block and you need to allow it to be downloaded. Maybe that's your issue.

[@andreiyuzlenko2046]

Yes, I installed it according to the instructions, the computer has enough power, nothing was blocked, the installation went well. The company has not yet responded to the email, I wrote to them 2 times. If I figure out the problem, I'll let you know.

[@jku392adventures]

@@andreiyuzlenko2046 okay I hope you have a swift answer from them. And yes definitely let us know what the fix is. Just in case anyone else has the same problem 🔥💯

[@andreiyuzlenko2046]

Reinstalled the program, it works! During installation, I did not turn off the German language, did not make any changes. I did everything by default. Thanks for the tip, I've been looking for a long time where to download a relatively recent version of the program👍🏼

[@idcool02]

Hello Guys, I have the same problem and the same message of issue, can y help with this? What we need to do to escape this thing?

[@AndrewCharles-r9l]

This software is totally free it evens shows it free when you start to install it

[@E92_Jeff]

Where

[@jku392adventures]

Sure it's free, that's what I tried originally, but there was too much guesswork with the free stuff. I even had to pay for a membership to be able to download the 200gb file. So free but no instructions, and no assistance on downloading. If you watch the video. That's one of the first things I mentioned

[@AndrewCharles-r9l]

Do your research people I have been installing since 4.15.16 right up to 4.50.40 for free. I see my previous comments have been removed. So how it goes.

[@jku392adventures]

@AndrewCharles-r9l WHAT are you talking about? Hahaha

[@jku392adventures]

What comment was removed? 😂