Ultimate Guide To RGB Controllers And Adapters

[@SignalRGB]

Important: While you can connect 12 QL fans on the Lighting Node Pro, and the Commander Pro controllers, It's only possible if you use SignalRGB, iCUE will only let you do 6 QL fans on the Lighting Node Pro and the Commander Pro. You also will experience laggy effects if you connected 12 QL fans on the Lighting Node Pro and Commander Pro, so we still recommended the Commander Core XT which doesn't have this issue. However, you can run 12 of any other Corsair fans on the Lighting Node Pro and Commander Pro without any lag issues.

[@mariusstoica2289]

How do you connect 2 Commander Core controllers for multiple vents?

[@SignalRGB]

@@mariusstoica2289 Can you explain what you mean by that?

[@mariusstoica2289]

@@SignalRGB so I have 2 commander core and I want to use them both. Is that possible?

[@furkangunes9508]

@@SignalRGB dude' Is it compatible with the back-of-monitor ambience for Philips hue?

[@Theodore638]

Can you guys help me connect my Lian li al120 fans to the razer chroma argb controller

[@snakeeyes7101]

One of the most comprehensive guides I've seen out there for RGB lighting across the board. SignalRGB just keeps standing out. Cheers!

[@dennisheusschen7273]

it also stands out when looking at ram usage.

[@raphaeloliveira3615]

I was like: why signal rgb doens't recognize my coolmoon controller? After this video: it's just a splitter LOL

[@fadillah6014]

Which type you had? I planned to buy from that brand aswell

[@raphaeloliveira3615]

@@fadillah6014 The coolmoon splitter is kinda nice, but Signal RGB only sees it as a splitter. It going to duplicate whatever effect you're trying to all stuff connected to the coolmoon controller. I have the simple one, the non music type.

[@righteousji]

​​​@@raphaeloliveira3615i have the coolmoon controller but.. Can signalrgb detected it in non argb sync motherboard? I just connect the controller to sata cable and not using the 5v header and just change with the remote

[@def2020]

@@righteousji wdym non argb sync motherboard but later on you say not using the 5v header. Does your MB support argb or not? thats important to know

[@FinFu509]

I was having major headache understanding how bad those components are designed and how miserable mobo RGB controllers are at the moment, and here you come! What a savior!

[@AndyRicAudio]

I’ve been searching all over the internet for this information without success and then I find this video! Thank you so much!

[@592Johno]

This is the video I absolutely needed. This answers all my questions finally!! I plan on getting Arctic p12s ARGB with Razers RGB controller. Noctua-ish performance + top tier RGB effects wo using crappy, confusing, proprietary controllers.

[@kevinob6384]

thats what im tryna do

[@biszarr1513]

solid combo; I have the fans in my pc so I just need the controller

[@andrewmcmillions3138]

​@@biszarr1513 I'm in the same boat, I have the arctic p12 fans in my pc I just need the controller. Are you guys happy with your razers controller with the Arctic fans?

[@biszarr1513]

@@andrewmcmillions3138 I'm glad you asked this because I recently found out these things have true daisy chain so you dn't need the controller! just daisy chain them to an rgb port and you will have individual control

[@andrewmcmillions3138]

@@biszarr1513 yes I love that they are daisy chain, sadly though my motherboard doesn't have a-rgb port and that's why I need the controller :/ might just get a new motherboard soon, mine is like 7 years old, it's a gigabyte

[@apexsplash5088]

This has been the most informative video I've watched in the past 4 months of watching computer building guides to help with my first PC build

[@AnthonyGuy-z7u]

Just like a lot of the comments I'm just reiterating - you've done a comprehensive and scientifically laid out video here in a short timeframe. Thanks very much.

[@nkuete]

this is UNBELIEVABLY helpful. I've wanted to get in to Signal RGB for a long long time and this is taking a lot of the confusion away.

[@deanobuzz372]

Good to see you still leading the show with rgb tech.. love all you do man.. still happily sending money your way.

[@Kallenikkun]

Finally, this is what i need 😭

[@Fonzizzz]

This is the first time the 0.75x speed has actually come in handy as you talk very fast. Great video

[@Brentt777]

I hate when KZbinrs talk fast, it just makes it all the more confusing

[@grandpixel]

0.50x for this guy

[@andiwolf3334]

Thank you SO much, after about 2h of searching and finding noone talking about the difference between splitting and daisy chaining, I finally got my answers and also so many solutions to my problem :) Thanks!

[@purpleskues]

To the point, and extraordinarily informative. 10/10

[@1nvasive]

Thanks this was so useful and it's something that other companies should do

[@Theorica]

I just recently discovered this software and love it! Using it on 3 different systems. My kids and my own. I've recommended it to a few friends as well. While the kids are using the free version, I decided to subscribe (I do really despise subscriptions! Though, this one is quite reasonable). I chose to help support the effort over my reservations on subs. ;) I can confirm that this works using the 'upHere 5V 3Pin ARGB PWM Fan Hub' (I think it is called the P7P) with a bit of configuration. It was flawless with my Cooler Master A1 V2 ARGB controller. Glad I found this software.

[@kasqua1042]

One of the most useful guides on this topic!

[@bladerjareerofficial2436]

U got skills plus everything was detailed perfectly!!

[@AntisepticHandwash]

Excellent video. Systematic and concise while being comprehensive.

[@TheBrewjo]

Thanks mate, this is the video I needed. Last year I jumped into my first new PC in several years with the Corsair 7000X. Now I'm building a new PC for a family member on a budget and they want the rainbow spewing unicorn effects as well (on a budget). The Corsair ARGB is so good it's flaw is I didn't have to learn anything haha!

[@Zach-jz7vh]

Awesome, very helpful video! keep up the great content!!!

[@AnotherAnonymousMan]

Genuinely outstanding work. Thanks!👏👏👏

[@tropicthunder332]

Razer Chroma ARGB Controller works like a charm😊

[@ohiocitydave]

God I wish I saw this before making my first rgb build. Would have saved me so much headache, frustration, a bundle of cash, and having random cables and adapters now strewn about my apartment.

[@burtpanzer]

Very informative for such a highly complex topic. Only thing I think it may have missed was the problematic use of Y splitters and hubs.

[@SignalRGB]

I covered that hubs are basically just splitters that dont offer individual rgb control. At the very start of the video.

[@joy_0109]

I'm more confused now. Pls do a video on how to wire these. At least do the non-proprietary wiring guide.

[@austinharding9734]

dude that was thee most ultimate video ive seen for any ultimate topic with thee most ultimate description i have ultimately watched, it ultimately answered every question in the most ultimate manner, but more importantly concise an thorough what can i call you Mr. Ultimo, Dr. Ultimately, or the know-it-all~timate guy? ill be honest i still have a question plus a comment, 1st what IS Signal RGB? i thought i only needed to download icue to get the controller up and running? anybody? comment, the commander pro xt has the 4 pin rgb, but it has 2 different ports on the side, a different 4 pin, and another 3 pin, i think the one you missed says ID on it which instructions jus say any compatible corsair device, but this out too, i have 3 corsair fans which have a 3 pin connector that does NOT fit anywhere on the commander pro xt, its a tiny 3 pin with a notch on bottom left where commanders 3 pin has 2 notches on bottom, so with adapters i have everything non corsair hooked up all except the only corsair fans i have which cant connect, i think ther called hydro idk im pretty sure there corsair

[@SignalRGB]

SignalRGB is our alternative RGB application that works for all brands

[@austinharding9734]

@@SignalRGB thank you yea that 3 pin i thought was for a corsair was actually to a thermaltake so... thang i dont get is these companies surely must know there are workarounds to there proprietary bull crap so why do they continue to use them? i think either they get enough newbies that dont know bout it and assume they must commit or ther jus lazy an dont want to spend the extta money in productiin costs to switch them to universal, took an act of congress to force cell companies to standardize phone chargers may need that agaim, i just assumed ISO or ASM... had that authority tho

[@TheWirkkalaShow]

I’m a dork. I forgot to allocate my Corsair fans. I got it now though 👍 this software is great

[@asapmatin99]

Omfg THANK YOU dude ❤ I’m looking for a simple explanation for 10000000h 😂😂

[@Uglier.]

This is going down in the history of PC building KZbin

[@RedxAx2]

Neeeeeed it, thanks, its a critical thing that many companies should do it

[@delgaldo2]

exactly the information I was looking for. Thx! 👍

[@GameIT.]

Thanks! very helpful for my future builds/upgrades.

[@peterc5544]

i was looking for this video i need some adapters to work,thanks very helpfull

[@Nathanduong0122]

Thanks for the video. I got - x3 groups of lianli Sl fans v2 -> 1controller -> MB usb - x2 strimer v2 -> 1controller -> MB usb - x1 LED phanteks strip M1 -> 5v RGB header Those LianLi fans and strimers got lag, not smoothly So what would you recommend for the best performance in RGBsignal? Thank you so much

[@Michi-go5xi]

Very informative... But now I'm 100% going to build a non RGB PC because this is too complex for my small brain

[@yoo.gaming4534]

Awesome video. Probably the only in-depth video that hits all the major RGB brands. For Lian Li Infinity fans (that are connected to their controller), do you have to use the 5V ARGB header on MB for Signal RGB to control it? Or will Signal RGB be able to detect the fans / controller via the USB Header? Asking b/c Signal RGB can detect Corsair Commander Core via USB connection.

[@SignalRGB]

You can use either usb or 5v header. But with 5v, the first channel will be copied onto all other channels and there will be NO LAG. With usb you get full control on all channels but you might experience lag issues as mentioned in the video because Lian Li made their controllers poorly.

[@dansiltala283]

@@SignalRGB question(for the Lian Li infinity fans), if i still have the usb plugged in, so i have PWM fan control, but i also have the 5V argb cables plugged into the motherboard, will the 5V argb cable take over the rgb signal instead of the usb header, so that there will be no lag? thanks.

[@emptyingthecup]

Great video. Perhaps I missed it but do you require both a hub and a controller? My mobo does not have argb headers, so I purchased the Razer Chroma hub, which has 3 pin male heads. However, the argb fans I purchased have 6 pin female heads, but it comes with a controller, which has a sata cable and a 3 pin female head, which can connect to the Razer Chroma hub. I was hoping to connect the fans directly to the Razer Chroma instead of going through a controller which then goes to the hub, but I'm not sure if there would be an incompatibility of voltages. Also, it seems a bit difficult relatively to find 3 pin argb fans.

[@palisocm001]

thank you for the explanations and links.

[@joerockwell9198]

Thank you for making the sea of RGB more palatable... 😊 Even as an IT guy I was like WTF 😂🤣

[@BillBittel]

Where is the link mentioned in the video to the instructions to get Aquacomputer RGBpx strips to work in SignalRGB? I don't understand why controlling these LED strips would be any different. They are standard ARGB LEDs with a Molex Pico-blade connector instead of the terrible "standard" ARGB connector. The RGBpx cable connects the LED strip to a port on the Farbwerk360. SignalRGB should be able to control the LED strip like any other LED strip. What am I missing? Great video BTW!

[@SignalRGB]

Added that! Check again. Forgot to, thanks for that reminder.

[@BillBittel]

@@SignalRGB Thank you! I think I understand why this needs to be done. I read somewhere on Discord (can't find it now), that the Aquasuite (AQS) program will always attempt to control the Farbwerk360 (or Nano) when it's running. So if you use AQS for your cooling component control, but you want to control a FW360 with Signal RGB, there will be a conflict, not unlike having Signal RGB control a Corsair RGB controller but having iCue running at the same time with the RGB controller enabled and under iCue control. The procedure at the link you provided uses the Ambientpx feature which causes the LEDs to track video color info. Since Signal RGB uses a "canvas", this is how you get the RGB color data in the FW360. Is this correct? Also, once it's set up this way, is it then OK to have AQS running and controlling fans, pumps, etc, while Signal RGB is controlling the FW360? Final question - The FW360 and Nano support Transparency which allows RGB effects to "bleed through" higher level effects. RGBpx ports on the Octo, Quadro, D5 Next, High Flow Next, etc. do not support Transparency. Is this feature maintained or even relevant when the FW device is under Signal RGB control? I know it's kind of weird to post detailed questions like this in a KZbin comment, but since you obviously read these comments, I figured I might as well ask. Many thanks for any additional info.

[@pheelix-]

1:01 You got that backwards. G, R, B is Ground and +12v is just that 12v Positive. Also there isn't a different firmware on the Lighting Node, the 2 ports are just standard argb ports. You can plug in normal argb strips into them and they will work fine. The same goes for the 1 rgb port on the commander cores and the 2 LED ports commander pro.

[@SignalRGB]

Thats true about the first part, it is technically ground green, ground red, and ground blue, but I’m not sure what you’re referring to about the last part. The lighting node at what part of the video? The only time i mention firmware is with the Spec Omega controller which is true, it is a lighting node pro controller with a different firmware that forces the first port to act as an led strip in icue and SignalRGB.

[@pheelix-]

Well I don't understand why they would need to put different firmware in that Lighting node pro controller. As all lighting node pro controller ports act as a led strip in icue anyways. You just select RGB LED Strip in lighting setup. The 3 pins are standard ground, data, power.

[@SignalRGB]

@@pheelix- Thats just how it is, the Spec Omega controller has a different firmware so that it shows up like the case in iCUE. I have the firmware file too and if I gave it to you and you flashed your regular Node Pro it would change into a Spec Omega in iCUE.

[@pheelix-]

@@SignalRGB well that is lame of them. Do you have the original Node Pro firmware so people can change it back into a normal one? Or maybe add it as a option in SignalRGB. I don't have that case or signalRGB, but for those that do it would be better then having to buy another controller if they don't need to.

[@MultiSciGeek]

Excellent tutorial! However, I have RGB fans but not the controller box. Can I still connect them in that RGB pin setup where all of them light up the same? Secondly do super cheap motherboards even support this option?

[@qulien7123]

This was a nice deep dive into RBG controllers, but didn't answer a question I have. Some RGB fans come with additional SATA power plug. I never know if this is necessary, or if the regular fan + argb header on the motherboard will suffice. For example, I have an AIO with RGB fans. It comes with a little controller that lets you change the colors and color modes physically, but you have to connect it to SATA power. However, you can then disconnect that connector and the LEDs will remember the set colors and still work. Recently, I bought a new AIO, which has an ARGB connector, as well as the regular fan connector, and also SATA power. With this one, I was hoping I could completely forgoe the SATA cable, as the ARGB connection to the motherboard should enable me to control the fans this way. However, with this one, the LEDs won't light up _at all_ unless the SATA is also connected. I don't understand that. And I don't understand how to figure these things out before buying RGB stuff. I would appreciate any help, insight, resources.

[@cannonball_Z]

thanks for this!

[@bme7491]

Ultimate guide is right.

[@samiijay93]

Question! How do I control more than 6 fans? I have 6 (AF120)fans connected to a Commander Core and 2(QL140) fans connected directly to the mobo CHA1 and CHA2 with the RGB cables going to a Corsair fan LED hub.

[@armanaby5]

HANDS DOWN THE BEST SOFTWARE ON THE MARKET FOR CONTROLLING RGB AND SYNCING DIFFERENT RGB HARDWARE.

[@LUCIfer_72]

Best software ever ❤❤

[@dansiltala283]

At 10:50 for lian li fans I can get no lag with the 3pin 5v, that's good to hear, my only question is for fan control should I use the 2pin fan connector or the usb header?

[@tubelesstrippin]

11:38 and if you have all of those plugged into youre mobo for instance the argb is plugged into the jrainbow 2 port on my mobo then what component would i assign to it, a custom strip with a value of 120 or what nothing js leave it? i got the 5v argb/pwm plugged in lol id like to use it since i got a fan curve in my bios.

[@Jarrahfe]

11:37 , is the 3rd "5V ARGB / PWM FAN CABLE" is to make the fans synced with the motherboard software?

[@Roblox-cf4rw]

I just bought a SAMA case with a argb hub. I have heard signal RGB is the best to control fans. Will I be able to use signal RGB with these fans and header?

[@melódic_breeze_VIIIV]

Hi, I’ve just bought a triple pack of Corsair AR120 fans but cannot get the LED’s to work, fans are running through a Vida splitter but no lights. Both cables that come from the fans are 4 pin meaning they are not addressable yet the cpu fan that came with the pc is plugged into a 3 pin argb header labelled jrainbow1. Does this mean I have to use a header which has 4 pins and if so will the LED just be the same static colour all the time seen as it’s non addressable or will it run its own cycle of colour without any control. I have a header labelled jrgb which is a 4 pin and looks right but I’ll need to buy another splitter as this is the only 1 on the M/B

[@RyaNGamingYTube]

Excellent bro!!!

[@Bluelagoonstudios]

I use a Razer argb controller, and this is a great controller used in a totally BeQuiet system and an Alphacool AIO that can be modified in a custom loop.. In my next build, there will be a Razer, a Aqua computer quadro for the fans and pump from my custom loop. And a controller from Lian Li fans, and case. This will be fully automated. But I think I have to get adapter cables for the Lian Li uni fans. 3 on top with a EK-rad and 3 on the bottom also with a 4,5cm EK rad. This system has also 2 real blacklight mini TL tubes, on the side, together with my pump/ reservoir combo from EK the case is of course the 011 dyn EVO XL. It's only sad that Signal RGB doesn't support AMD GPU's. because that one is a 7900xtx. That can be a problem.

[@caivsivlivs]

the Aquacomputer farbwerk 360 on amazon looks like an old version or something. the picture only has 4 2 pin RGBpx connectors (the white ones) and none of the 3 pin black "regular" ARGB headers. did old version only have these proprietary connectors?

[@MidLifeGamerGuy]

I love what you guys are doing here, the only reason I'm not using SignalRGB is the damn Strimmer V2 full control. Looking at the Arduino board work around and don't even know if that'll help 😔

[@lucaschristian6442]

I can't find any of the ARGB controllers mentioned, just the cooler master argb+pwm hub, which I believe is not possible to configure each argb individually

[@garyc5245]

Now that there is all this single cable triple fans (Thermaltake Swa, Phanteks and others. What controller can handle 90 LEDs per port (Phanteks and others are 30 LEDs per fan. I just did a build for a customer and I want to make sure I don't burn up the argb header or the Phanteks NV7 controller on the case. There is also case lighting LEDs. The Corsair product with the daisy chain hub looks to be the solution, but I need to find an adapt cable that goes from Phanteks wiring to a Corsair plug.

[@Spoodily]

I have several groups of 4 Lian Li Inf 120 fans I need to hook up. I was going to use the razer chroma hub but it has an 80 led per port limit and I need 160 led per port.

[@Pancake-k1c]

How many channels can i connect to the lian li sl infinity controller before it starts lagging?

[@eserblessfire]

Can you daisy chain different devices to the mobo stuff argb slots and adress every item individually? Im confused about that

[@prg29]

In most cases no. As signal rgb won't identify the individual channels. So if you want the same effect then ok. But if you want individual level effects best to get a controller

[@Iconguy24]

What about lianli 216 case ..the hub which comes along with case is that just splitter or a geniune hub to control each fan individually?

[@CharlesSmith-io9fp]

Does SignalRGB have a program that lets you control RGB colors via temperature probes? One color at cooler temps like say a light blue, and change to a red color at higher temp?

[@Drippysteves]

So, if my motherboard doesn't have any argb connectors, but I connect a supported argb controller, I can control my fans with signal rgb?

[@JoeChapman-e7q]

can you connect a 3 pin 5v header to a 4 pin 12v using an adapter?

[@cubix5159]

What if you daisychain you fans like the lian li al 120 v2 and put them in the hub would you be able to control each one of them?

[@wusaint]

Almost all of the individual controllers for the USB 2.0 headers that don't use proprietary connectors are out of stock I'm assuming because they no longer make them. Any other recommendations?

[@adamdev9391]

At 5:21 you show the Corsair 5000T case, but is that case compatible? I can't get my RGB to show up in Signal RGB. they are there in iCUE, but i'd much rather use SIgnal as my RGB hub.

[@SignalRGB]

5000T is compatible, you have to configure the RGB strips correctly. We have a tutorial that can help: kzbin.info/www/bejne/iH_KoapnnZ6Mnck and also kzbin.info/www/bejne/o6XceKCIa7B7acU

[@CharlesSmith-io9fp]

Is there any reason that I shouldn't use a Corsair Internal 4-Port USB 2.0 Hub | 4X 9-Pin USB 2.0 Ports | instead of the NZXT Internal USB Hub 3 | AC-IUSBH-M3 | 4 Internal USB 2.0 Ports? I have all kinds of Corsair equipment from 2 previous PC builds. I want to thank you for the section on adapter cables that let you connect Corsair products with other brands of hubs and such. I never knew about incompatibility problems until I spent way too much on Corsair. Thanks again.

[@8Diakon8]

Something similar for fan controllers would be nice.

[@speedracer9132]

Which hub would you recommend if all I want is an ARGB fan splitter to have 6 fans on my Arctic 420 AIO used with the Asus B650EF matching fan speed and ARGB? I’ll also be using 4 phanteks case fans, I’m wondering which RGB software is low resource intensive and works well with my parts?

[@Djaym0]

you ever get an answer to this? I plan on using the phanteks d30's and thermaltake swafans in my rig but phanteks doesnt have a good rgb controller to use?

[@whoknowswho832]

you can actually skip corsair ports if u put jumper on 2 middle pins so u can jump from 1 to 3 (skiping 2 with jumper) also u can diy build corsair controllers with arduino and clp codes making great controllers for any rgb needs , and about strimer plus v2 just build special diy controller and can control it all of leds seperatly (even more controll than lianli itself) with OpenRGB no L-connect needed ;) . can share pcb if anyone wants it

[@angelogalileo]

I didn’t know that you had to have done so many high studies to master the RGB ;)... I am very confused and I wonder now what to do ... I have to manage on my ASUS Aura Sync motherboard : 7 ASUS TUF ARBG fans with an AIO Corsair TITAN LCD with its proprietary iCue format (aura sync compatible). Which controller would you recommend? Thank you i f you time to answer :)

[@Matteroonie]

I just wanna know if different controllers allow for different rgb modes

[@eseb1ghu3ro]

i may have missed it or misunderstood but i can connect the lian li strimer controller to a razer chroma controller is that right?

[@CountDabulaTV]

Thanks so much for this helpful video, I learned a lot! But I have one question, what about Phanteks fans? They come with a non standard plug that looks like the 3 pin rgb Lian Li plugs, would it be possible to use one of the Lian Li ARGB controller with Phanteks fans? Or should I buy six adapter cables and the Razer RGB controller separately? They look like they would fit in the AirGoo adapters.

[@alfredl3831]

I have been using SignalRGB for a while now and I love it. Can you use dual Razer Chroma Hubs? I need one more channel to finish my setup.

[@SignalRGB]

Yes you can

[@alfredl3831]

@@SignalRGB can they be on the same usb header or do they have to be on different ones? I really appreciate your help.

[@SignalRGB]

@@alfredl3831 That should be fine

[@Ar7eM1u5]

I have a question , sorry in advance if it has alrdy been brought up : Does Signal recognize and use properly, two separate Razer Chroma Controllers installed in a system?

[@unknowncalibur5242]

Is there an RGB controller I could use for the phantom spirit

[@lunachibii]

why signalRGB does't have one time purchase option instead subscription?

[@kassabro7919]

do you know about 6pin fan connectors ?

[@socaldayve]

0:38 My old B450 Aorus mobo has two 4-pin headers labeled "D_LED" that can be toggled between 5v or 12v. I was always confused as to whether these are compatible with ARGB products. From your description, the answer appears to be yes. Am I understanding this correctly?

[@balintApizza]

probably not but I would try googling it

[@Junglemama0]

Hey bro, where is that bullet train you are trying to catch, as a teacher, slow down. What are you taking?

[@derekgoff4328]

So my Corsair and Liam li both need special adapters for my rgb to sync? I’m about to put this together, rather know now than before I get to it 😂

[@derekgoff4328]

Also - I have 2 of the razer chroma hubs & a fan hub from arctic case fan hub also. Idk if that’ll fix my issues or not, I’m waiting for parts to come in the mail

[@coltonkoepp655]

So question about the Unifan to generic 5v 3pin adapter cable is that needed on a per fan basis or if you use the magnetic daisy chaining 1 cable per 3 fans

[@SignalRGB]

1 cable per 3 fans

[@oskartorres8408]

I have cooler msste jalo 3 in 1, so Is better to use the hub inset tonconmect the fans in chain directly tl the mother board?😊

[@marcelonox5002]

Thanks for the video. I'm still confused though. I've recently purchased a Cooler Master HAF 700 which includes an internal ARGB controller. The problem is that while it lets me control fans led, fans rpm are always stuck to 100%, which is frustrating. My question is if there's any solution to this. Like a ARGB fan hub that can actually control fan speeds over the motherboard or any other way. I'd really appreciatte any suggestions.

[@ajitmanna5730]

Can we daisy chain argb fans and connect to cooler master gen 2 argb controller a1 to get full independent argb control ?

[@SignalRGB]

Technically, yes. Just keep in mind what the limits of the ports are which I mention in this video.

[@ajitmanna5730]

@@SignalRGB thanks.🙃

[@kimxeasarmangabat2700]

Hi i love ur software but i have question recently i got a gen2 fan that is chained together then when i first try to use it with signalrgb i was able to control each fan even thos its chained but now i cant after restarting the pc also the fan is plugged directly to the mobo i want to control my gen 2 fan that are chained how can i do that?

[@silly_lily6241]

just for clarification. if i buy a corsair fan with the iCUE Lighting Node CORE. do i still need the iCUE COMMANDER CORE XT?

[@MrWhateva10]

Lian-Li SL-Infinity fans have 40 ARGB LEDs per fan, and the Antec C8 case has space for ~10 fans. Seems like there aren't any controllers ready to run this out of the box in 2024; is that right? Or do people just run multiple controllers?

[@Emil_m]

Are there any RGB Hubs that can be set via software but then store all the settings on board (meaning you can uninstall software and the settings remain throughout PC boot or different OS)? I'm getting B650 AORUS ELITE AX that has Fusion software, but that has to be run also and there seems to be no bios-level settings to control for RGB? (will check once I get the mb). But still, would be nice to have the best of both worlds - change settings via software, AND have them saved through hardware.

[@wubbsy]

Used the Razer Chroma Controller for a while. Good controller. But damn all these controllers are so weak. I was searching for a new controller for my new build but the main led strip around the front already has around 200 LEDs. Gotta build a custom solution again. You don’t happen to have support for microcontrollers?

[@ytice695]

Do you know if I can control the rgb on the fans on my cougar duoface case

[@Dark_SnipeTM]

so if i dont have a 5v argb port i can just buy a hub and then it works?

[@Tarmian-mp7bw]

Can I use Corsair fans With non Corsair Controllers?

[@sniperdoc8404]

I think the LianLi v2 controller has issues with the MSI MEG ACE Z790 onboard ARGB controller. When the LianLi controller is connected to USB and ARGB_1 for example, it causes the ARGB_2 and 3 to not be controlled properly. It also causes the Dragon emblem and partial LED issues on the ARGB_2 and 3 controllers. I've read that this LianLi controller has all sorts of issues and people just say not to use them... hope this gets sorted. :( right now my MEG and ACE logos won't work at all, and when I lock my system for the night and come back in the morning, everything's reset lighting wise, nothing is following the canvas I set the night before. However, my ACE and MEG logo appear, and the Strimers are doing their own thing, along with the 6 120mm fans I have on a Commander XT, doing their own thing. If I restart SignalRGB the canvasing of the lighting works fine, but I lose my ACE and MEG logo again. Doesn't happen if I disconnect the LianLi controller. :(

[@huseyinakkoc1062]

i was looking everywhere for this info and couldnot find any usefull or correct info and after 10 hour this video was released too thank you, it was a need. by the way i wanna ask something. i have msi b550 edge have 2 port but signal argb see only 1 rainbow port. why is this happenig? i afraid of this to happen when ı buy razer controller too