UPDATE How to Unplug Connector on Oil PSI Sensor P0521 P0523 No Oil Pressure Chevy Truck Silverado

[@Donnythelatemodeltech]

Check out the Original How to Repair Video Here ! kzbin.info/www/bejne/r3K1hmmNp8-Hd7c

[@beetswayba8634]

Does a new sensor have to be tightenrd to the same tight position?

[@Donnythelatemodeltech]

@@beetswayba8634 nope

[@julzparrilla724]

YOU ARE THE MAN!!! Everyone else keeps BYPASSING that part. They tell you that you have to do it, but they don't show you how that clip ACTUALLY DISCONNECTS. THANK YOU for posting THIS VIDEO on that Stupid Clip! You are a GODSEND !!! 😎🤘🏼

[@vailian520]

Wish your video was at the top of the list. That harness gave me grief 😂

[@wesliles1387]

This is the toughest part of the job! I was at it for 2 hours and then found this video. THANK YOU! I finished in 20 min after watching this.

[@Suchayoutuber]

Thank you for actually showing how to get the clip off without breaking it, as almost all the other KZbinrs kind of forget that part

[@Donnythelatemodeltech]

oh yeah! thanks for sharing

[@mikem2492]

OMG...Thank you! I struggled with that connector for an hour. Watched your video and got it off in 20 seconds.

[@vincentvalencia7177]

Thanks for this video!! 2011 GMC Sierra 1500 5.3: I just finished replacing my sensor 10 min ago, and this video is what really helped! The only problem I had was fishing out the filter. I used a flat head screwdriver to finally get it out. Auto shop was going to charge $150 to replace bringing my own part, the lowest I found, so it only cost me $37 (Dorman sensor on amazon) doing it myself thanks to this video. I appreciate your help!! Now a subscriber!

[@LH81633]

I did mine face timing my wife’s phone, faced mine at switch and used hers as a monitor!!

[@johnminger20]

Great idea!

[@odiarroyo6144]

Wow i didn't think of that! Ill do us this info tnx

[@MrIvesston]

Thank you for showing where to push on clip. That made it easy

[@KOOLAY203]

GENIUS. Wish I saw your comment before I did this job.

[@LyonhartZ2]

You sbould have done the reverse. Get her phone dirty in the engine bay and use yours as a monitor. Just kidding

[@indycog]

THANK YOU! All the videos on replacement leave off the first step of removing the clip! I was able to get mine off thanks to this video.

[@kevinpowell5677]

Man bless your heart. You saved me from having a damn heart attack. Thanks a lot

[@Donnythelatemodeltech]

Most welcome

[@yblocevol]

Thank you!!! Showing how to completely remove the safety clip plastic is what did it for me. I couldn't get mine out until I did that.

[@chrisrodman3664]

I fought with this stupid connector for an hour, watched literally 2 minutes and 30 seconds into your video, walked over and popped it right off. Thank you!

[@mexi0501]

Thank you for saving me much grief tomorrow. Doing all the research I can before I start breaking things.

[@Media-hd1su]

You are the man. That stupid push part after lifting up the grey piece that locks it in is what I was missing. Thank you!

[@22lspb]

You are the only person I’ve found to show how to disconnect the plug, specifically, for the 2009 GM 5.3 engines. Thanks for the advice!

[@johnminger20]

Thank you so much for going through all that trouble and posting this. I spent about 2 hours trying to figure out how to remove that, and I finally gave up and just reconnected the hoses I had removed. I was able to get that gray clip up, but I didn't know you had to then press on that same part (I was trying to squeeze together the two blue plastic pieces, to no avail). You have saved me from removing the entire intake to get to it!

[@RR-gm7bw]

Even after this great video, it still took me over an hour to get it off! For anybody struggling, try pushing the connector down hard before squeezing. I had to keep wiggling it up and down (not side to side) before I finally got it to release. Thanks for the great video!

[@Hotbwoy17]

You saved the day with this video!! I was battling with that connector for what seemed like forever. Good job!

[@LH81633]

This is absolutely the best way to do this job, all you need is the socket, a small elbow swivel and that extension! Of course a simple wretchet or breaker bar. But this is the easiest and most simple way you don’t have to go buy all them fancy tools like on all the others videos.

[@karnellvickers8712]

Thanks for the update. I'm not a "mechanic" but I try to do my own stuff. I had the tools except the special socket. So it was $9 and $7 for the filter which was also great to know. GOT THE JOB DONE IN 45 MIN. BTW they told me it was a 4 hour job. Lol what a RIP. Thank you for your video.

[@drewsterdu_8221]

You sir, are a life-saver. Especially the part where you said if the white clip went flying (my words in this case), it’s fine lol. Thank you for taking the time to go back and do this.

[@Donnythelatemodeltech]

Glad it helped!

[@iUsernamesHate]

YES! Before this video, it was like trying to solve a Rubic's Cube in the dark. Two thumbs up.

[@Donnythelatemodeltech]

🍻

[@TheRobq7]

You have no idea how happy I am you made this follow up video. Thank you. I was extremely frustrated and ready to give several youtubers a come to Jesus meeting

[@danbell8508]

I have to say that this video helped me finish changing the oil pressure sensor on my 2009 Silverado. The fact that you said listen for the click on the plug did it for me. Then I understood how the plug worked. Now after watching several videos I can change the sensor in maybe 15 minutes 30 tops. Thank you so much. Dan Bell Modesto California.

[@Donnythelatemodeltech]

Most welcome Dan. Glad it helped.

[@USMC0621TX]

Bro!!!! I had to go through the comments to find this video. All I had to do was push on the side of it. You’re awesome for putting an update for the conector

[@alajones5428]

Thank you so much. Yours is the only video that shows the most difficult part of the process.

[@GMFYZFR1]

I am not a religious man but God bless you nonetheless. Saved me from throwing in the towel and taking my truck in

[@brandonschrage6224]

My goodness. I guess it has been a decade since was a tech, I'm embarrassed I had to look here to figure out how to get that damn thing off. Easy peasy once you remember how that clip works. Thanks!

[@Donnythelatemodeltech]

No Worries man, thats life. Glad it could help and thank you for the comment. Happy Holidays!

[@lhalby8554]

Thank you! I fought with this connector for two hours before watching your video. The entire job took 45 minutes after.

[@Donnythelatemodeltech]

Awsome!

[@irrelevanvideos]

Thanks for posting video of the actual clip, I couldn't figure out what type of clip it was. After I watched your video I literally had the sensor out and replaced 5 minutes later.

[@Donnythelatemodeltech]

🤙

[@Blackfootpigeons]

Dude!!!! You saved me! Only video I came across on how to get that F’ing clip off!! Thank you thank you thank you!!

[@Donnythelatemodeltech]

Nice

[@alfonsochavez8210]

Man I’ve been going threw 3 days of how to disconnect went tree videos & all seem to act like all u do is pull out....I was almost gonna give up & go to a mechanic...I took a nap woke up saw one video that was similar to yours then the next one was this video!!!! Thanks a lot

[@Donnythelatemodeltech]

👍

[@fredesman9019]

Thanks for the video, you got way better angles than anyone else. Tip for those with larger hands, I struggled for 3 hours trying to press the release in after getting the safety clip up, it's so tight my hand just couldn't move. I finally got it left handed with my thumb and pointer finger closest to the ground, the angles in that orientation were way better and it only took one try that way and it came off easy

[@ThePSO51]

Finaly someone explained how that clip works!! Thanks man!! I don't know kw how you got the camera in that position kudos to you!!

[@77crossed]

Thank you for explaining in detail the release procedure for the sensor plug-helped me out immensely!!

[@paulmyers5263]

Thanks for this video! I just spent an hour trying to unplug that thing. it was facing the far side and I couldn't see it enough to figure it out.

[@craigsmith5791]

Outstanding video. This was very frustrating before finding your video. Great attention to the details that matter. Thank you!

[@meetmonkey10]

I just want to say thank you for posting this because the picture I took of my connector didn't help me, and there were no similar connectors in sight to practice on. Would've probably broken the connector or spent an hour in an uncomfortable position trying to figure that out.

[@Donnythelatemodeltech]

👍

[@davidanker9438]

Lifesaver! I was about to lose my mind with that clip

[@markdawson4129]

@Thelatemodeltech - thank you for the video. I went ahead and tried the replacement on my 2008 Tahoe LTZ. The engine seems a little more set back than your rig than my Tahoe which required a hood removal. I was able to get the job done. The only hitch I ran into was using the EVERCRAFT brand socket from Napa. As the sensor was loosened the top of the socket didn't have enough clearance to extract the tool and sensor. I chamfered the top of the socket and that made the job successful. Your time in putting these videos is greatly appreciated.

[@markdawson4129]

For the next DIYer - suggest that after you install sensor, take note of sensor clip 'nub' position - this will help you orient the sensor harness in the right direction to clip on.

[@brianwhitis9390]

just replaced mine after you're videos and I never would have gotten my connector off without this video, thanks dude!

[@Donnythelatemodeltech]

😎

[@leswelch6314]

Thanks....that sure did help since the connector is shoved so far back near the firewall!

[@trentongustafson394]

Thank you lord for showing me this. Elbow deep right now and couldn’t figure the connector out

[@corvettebob96]

With the help of the video, changing the sensor wasn't as bad as it appeared. My nephews engine needed to idle for about 4 minutes before the gauge started working. Thanks.

[@kwerner]

Thank you for mentioning the engine needed to idle before the gauge started working. I just finished changing my sensor and thought I was going to have to take it off again, then read your comment. After idling the gauge worked just like you said. What a relief! Haha

[@keithrayeski6417]

This was hanging me up as well!! Your video solved it! I still don’t know how the rest of it is going to go but, at least I’ll get past this!!🤣 What impressed me was you didn’t have to go through that aggravation but went the extra mile! Much appreciated!!👍🏻👍🏻

[@Donnythelatemodeltech]

Most welcome

[@evancaylor4214]

Thank you so much for this. I couldn't figure out how to get that connector off before watching this, and other videos glossed over this part despite it being the most frustrating (for me anyways).

[@Donnythelatemodeltech]

Thank you sir. If have time please check out my latest loads , they could use some support. Thanks again.

[@The411]

I could not get that damn connector off till I watched this video. THANKS!

[@Dozah9425]

As soon as i saw the end of the video, after fighting for 30 min. I ripped that grey piece right off lol Thanks for the info!

[@Donnythelatemodeltech]

👊

[@MsBigdebo]

Oh my goodness, thank you so much!! My clip broke off and I kept trying everything to get it off and was about to give up until I watched your video!!!

[@Donnythelatemodeltech]

🤘

[@markruthers4675]

Cheers from Australia mate! Excellent video, I struggled with that bloody connector for couple of hours. Found your video and now my neighbors think I'm crazy because I was saying very loudly fan-bloody-tastic followed by oh shit is that all you need to do 😆. Thanks again.

[@RedneckShenanigans1776]

This is literally the only video that shows how to unclip the connector. All the other people are just like "Ok, now I unclipped the connector"

[@craigpablo3275]

Thanks so much for this video! I was so frustrated trying to get that clip off I was about to take it to the shop! You probably saved me hundreds! Thanks again dude!

[@Donnythelatemodeltech]

Yep

[@steveminecraft101]

Excellent video showing how to release the connection !!!!!!!

[@Donnythelatemodeltech]

Glad it was helpful!

[@morgan1hair]

Exactly what I was looking for, you're the man!

[@ind347]

Fantastic help, thank you! LS3 6.2 transplant into my 2012 Land Rover Defender. Tasmania Australia

[@CxMadeIt]

Man I bet that thing is sick!

[@ind347]

@@CxMadeIt Hi Chris. Yes, I love it! kzbin.info/www/bejne/pZilq6xurd2JhLM

[@pedrohdz1964]

I do my own oil pressure sensor replacement on my 07 Chevy Silverado , I learned to remove and install many years ago lol, is nice to seeing a lot of people getting a clue on how get it done 🤟👍

[@joecrush1118]

Thanks for the video, it really helped unclipping something you can barely see just feel. 👍

[@Donnythelatemodeltech]

Glad it helped!

[@johnbrian118]

Very helpful-the best I've seen. Wish I saw this earlier but I tried and gave up. But will try again! Thanks!

[@Donnythelatemodeltech]

👍

[@jonluckyman2260]

Thanks! I was really frustrated that I couldn't get that stupid thing unplugged. Easy peasy

[@CarrollCanada]

Man I love you. If I could hug you right now i would. Thanks I've been trying to get it off for so long.

[@beachdweller3378]

THANK YOU THANK YOU! This is just what I needed!!!

[@timlecount8690]

Thank you so much. Like the others, I would have been sunk without your helpful video!

[@Donnythelatemodeltech]

🍻

[@marlongarner4847]

Don't know how you made that look so easy because all I can get is my and back there and nothing else but I will see if I can crawl my ass back there now. 👍

[@rickypadron875]

THANK YOU SOOOOO MUCH FOR FAST REPLY.!!!!!!!

[@papergatorzfedducca7998]

Best video yet about this!!😂😂😂 New subscriber!!🔥🔥🔥

[@csrunner6296]

Very helpful! Doing this job this afternoon and that was the last thing I had questions on

[@Donnythelatemodeltech]

👍

[@JRoman-lx8xx]

Thanks brotha, best video for removing the connector.

[@juice8852]

Window switch also uses a similar connector tab and a long set of needle nose pliers from harbor freight help apply pressure to help depress that tab as well.

[@bonifaciosalazar3086]

Thank you so much you are the only person shows Video Exactly hou to get that Conector Off tris Your video helped mi very mach to Remuve that Oil ptessure Sensor wire Cop on mi 2011 GMC sierra 👍👍🙏

[@Donnythelatemodeltech]

🤘

[@larryhicks7446]

Thanks man for the video , helped me understand what I need to be doing since I'm working blind back there.

[@Donnythelatemodeltech]

👍😄

[@MrBogbor1]

You are a gift from above your video truly help me out thanks

[@skyandboss]

Thanks this problem I was having I'm a hr into doing this now figuring it out lol.. I'm was like I broke the clip lol...

[@RRPros]

Just wanted to say thank you Late Model Tech for your three videos. I would have never been able to change the sensor and filter without your videos. Sitting in the engine bay worked, I did break the clip trying to get the connector off, and it took many tries to thread the filter to get it out. Successful job but my hand hurts; it did take me much longer than you but you have a lot more experience. Hopefully you got a little commission from my Amazon order using your links. The sensor on my 2009 5.3L Tahoe was ACDelco Part# 12673134.

[@billycanojr]

This is great, man. Thank you. Unfortunately my connector is pointed right at the black plastic piece.

[@alexh5358]

Fucking same

[@alexh5358]

Corte Video how did you unplug it?

[@billycanojr]

@@alexh5358 it was a pain and tricky but I kept at it until I figured it out. Can’t remember exactly how. Sorry!

[@alexh5358]

@@billycanojr it's ok, I broke the gray fucking clip cuz I got tired of it, dont really need it anyway lol

[@DanielSpeakman]

Same...found a hole in the plastic piece in front of it big enough to poke a finger through to hit the push button.

[@____Hugo____]

Best videos of this issue repair. Thanks brother!

[@mikep6967]

You da man 💰this was what I couldn’t figure out!

[@connellatkinson1257]

Bruh..... you helped me tremendously

[@brockcoffron2474]

Thanks for the tip. Made the project simple

[@dontbetoomad2684]

You are a good good man. Thank you so much for this video!!!!!!

[@MonelloSavutano]

thanks,very helpful, which camera were you filming it with

[@glaistercorlett1433]

Thank you very much for this update. Exactly what I needed to know.

[@BornersCorner]

Thanks! Trying to get one off tonight! What year is this Silverado

[@hammerhead6537]

This video was extremely helpful. You must be half Rubber Band Man or a Yoga pro. Just curious, did you ever try to retrieve the clip or just say to hell with it? Thanks for the trouble you went to in order to make this video. The two videos you made on this sensor replacement are definitely the best that I have seen, unfortunately, I am getting ready to replace mine, LOL. Semper Fi, USMC.

[@Donnythelatemodeltech]

I just left it down there

[@ctlandscapemaintenancesolu494]

great job this was pissing off so much i was about to go buy a new truck

[@Lostsoal]

Thanks bro i was struggling until i saw your video big help in there thanks man ! ❤️❤️❤️❤️❤️❤️

[@manuelbarcenas8357]

Very usefull vid i was pushung the blue tabs and it wouldent come off thank you

[@kameronheiser183]

This helped greatly

[@tjn2254]

Bravo for the camera work

[@3-TTT]

Great vid on the clip man! Saved me tons a of time.

[@stephenroyle5410]

Great instructions - worked like a charm

[@isaiahvazquez1559]

You’re a legend man thanks!

[@JJBanuelos]

Nice video considering how tough that connector is to even get to.

[@charleycosmato5897]

Your super power is getting the camera to focus on the plug long enough to see shit! 🤣👍 Many have tried, but only one has succeeded.

[@joegudino7339]

“LIKE” for the effort bud!

[@ahadqayamali9542]

Thank you so much. Was ready to set my truck on fire then I saw this lol.

[@Johnball-ef3sn]

Saved the day for sure!

[@uriah4901]

A tremendous up. Thank you!

[@rollanibanez7432]

Quick question...so I recently had my oil pressure on my 2011 Suburban peg to zero...ran a diagnostic and got the same codes as you had mentioned in your first video. I sent it in to my dealership...DAMN...mad expensive for replacing the switch. However, they also had listed to replace the switch connector. Do you think I would need to do that? Or would just replacing the switch fix my issue...your video is great help!

[@mykv4792]

Ok nice now I got reference thanks!

[@rlxxviii9234]

You're the man!