Upgrade your fuel pump for better performance! infiniti g37

How to install 340 AEM fuel pump infiniti g37 g35 g25 q40 sedan coupe
AEM’s High Flow In-Tank Fuel Pump is designed for high performance naturally aspirated and forced induction EFI vehicles.For gasoline vehicles E85 Compatible
The AEM High Flow In-Tank Fuel Pump flows 340 lph at 43 PSI and is capable of supporting over 1,000 HP at 43 PSI.
Shop for Leds: bit.ly/38aLjnj
Hope you enjoyed the video don't forget to leave a LIKE and SUBSCRIBE also hit the BELL so you get a notification when new videos ARE POSTED!!!
Follow me on instagram:
Jules Mechanics official Page: bit.ly/2Dl9vl7
MY Car Page "VQFEDDY": bit.ly/35D6JJxr

[@flipmode00]

Great work.

[@matthewsmid8505]

This is solid except you MUST drill out the small black orifice at the bottom so that the FPR can bleed off all the extra fuel quickly enough - otherwise you will experience overly high fuel pressure all the time.

[@michaeldiguilmi7828]

Are you talking about the hole at the bottom of the basket thats covered with a solid black circle? You’re saying to drill out that black? I’m doing this install right now. Where did you hear this from?

[@matthewsmid8505]

@@michaeldiguilmi7828 NO not that. The tiny Venturi hole facing sideways that is part of the small black plastic piece on the bottom edge of the basket. It bleeds off fuel pressure from the fuel pressure regulator directly above it inside the basket housing. The hole is pin sized from factory but MUST be drilled out slightly to accommodate for the increase in flow so that it can bleed off pressure correctly. There are other install videos on KZbin that show this extra step.

[@michaeldiguilmi7828]

@@matthewsmid8505 yeah i finally found an install manual from cjm haha. Just did it all. Ended up doing a 3/32” hole. For anyone interested: host.cj-motorsports.com/pdf/370z%20Fuel%20Pump%20Tech.pdf

[@SlateBlue_VQ]

⁠​⁠@@matthewsmid8505I drilled the venturi pump(mine was gray) as well as the hole. My tuner said my fuel pressure was very good

[@officialaalexx]

@@matthewsmid8505I had asked my tuner about this and he said it’s only necessary if you have a 400 pump or higher

[@TeeeDaBee]

Which hose did you do you buy

[@user-xh6ip9mq6h]

Which filter u use Mine Didn’t fit well

[@TooLoudBear]

sae j30r9 fuel hose is not submersible.

[@olja1521]

so drilling bigger holes and wiring in a bigger wiring harness to carry proper voltage isnt needed?

[@matthewsmid8505]

He forgot to drill out the Venturi orifice at the bottom...he removed the black piece that it's a part of but never drilled the hole out. This will cause major fuel overpressurization because the FPR can't bleed it off fast enough.

[@SlateBlue_VQ]

I don’t think a bigger wiring harness is necessary but it is necessary to drill out the venturi pump as well as the hole to keep the right fuel pressure

[@ericocmdfinest7605]

What can i do to fix my fuel reader it's not working and i changed my fuel pump already and it still says full if the car empty or half if its empty ? I need help

[@pierresmith8175]

just clean the sensor itself but the car is still gone have gauge issues i cleaned my sensor and it still iffy

[@basementjesus]

there’s two sides, one has the pump and the other has the reader

[@basementjesus]

i believe passenger side is pump and driver side is reader

[@chancepringle4393]

Does this work for the sedan too

[@JulesMechanics]

Yes