Upgraded 3D printer | DIY 3D Printer

[@bharatbhushan8550]

This video helps me a lot in creating a new 3d printer at low cost. Thanks for the video. Hope to see your new uploads soon

[@MechNinja]

Hi...Checkout my new video of DIY 3D Printer complete build from scratch kzbin.info/www/bejne/joqwm2l6ftqgY7M

[@lonewolf14779]

I have watched both and have the this frame figured out her it is 2 @ 500mm, 3 @ 350mm and 2 @ 270mm...The farme size is going to be 350mm wide x 500mm long x 270mm hight from the back to the up right is 110mm...That all i can get, the bed mount you give nothing but I'm going to try...The bed is 310mm x 310mm the size of the bed heater back later today post more.

[@FahadAhmed-on4mj]

Stl file not found in description link

[@lonewolf14779]

part 2 I'm going to say is that other parts are right on but as for the control broad and LCD I'm going to go to Creality ender or cr series printer and the power supply (24 volt) the control broad any where from 30.00 to 100.00 by doing some looking you find something that will work the hot bed 24volt 310 x 310mm or 120 volt but you will need a relay and a hotend I go with a ender All Metal Hotend Kit

[@MechNinja]

I am waiting for more updates

[@musaddiqueahmed4662]

Hello sir 🎉 Can i increase size of working bed and machine...

[@MechNinja]

Yes definitely...check my new 3D printing video.....

[@musaddiqueahmed4662]

@@MechNinja Thanks

[@MechNinja]

Your welcome..... and don't forget to subscribe 😀😊😀😊

[@salemalnajar3127]

Could you please clarify how did you install the end stops specially z-end stop Thanks

[@MechNinja]

In ramps 1.4 there are 6 sets on pins for min and Max x,y and z axis. Just plug the 3 endstops in min of x, y and z....or if you have placed the endstops in opposite directions as of mine then plug it in max of x, y and z. If your endstops won't light up on pressing then change the orientation of its pin. Hope you get what you were asking...and in upcoming videos I will provide each and every detail.... Feel free to ask anything...and do subscribe it...😊😊😊

[@kishanvadoliya4738]

Can you used previous 3d printer Arduino program in upgrade 3d printer???

[@MechNinja]

Yes bro

[@MechNinja]

Hi...Checkout my new video of DIY 3D Printer complete build from scratch kzbin.info/www/bejne/joqwm2l6ftqgY7M

[@omurcan05]

Hello. Can you tell me the size and number of the chassis?

[@MechNinja]

Hmmm the size of the printers depends on the smooth rods you are using. If they are off 300 mm length then you can take the L aluminum extrusion according to it.

[@andresroca9736]

Awesome too!. Fully complements the previous video, where I was wondering about structure reliability. Very cleaver your solution again. Two questions please: What is the averange cost of this? and, How tight are the tolerances you've achieved with this and with the previous structure? Thanks again, and great job dude. Saludos 🤙.

[@MechNinja]

Thanks for the complement bro....The cost of printer depends on the components you are using. The PVC Printer costs me around USD, and for the aluminum printer has all the parts same except the aluminum structure. And both the printer structure is robust and sturdy. The aluminum one is more stronger though...But the printing quality was overall same and good.

[@andresroca9736]

@@MechNinja Hi. Thanks, pal. Gonna talk with a friend and see if we try it out. Saludos. 🤙

[@akshayyadur6438]

Nice one ..u don't use heated bed?

[@MechNinja]

My upcoming video will be a replica of Ender......Wait for it..it will have everything...😊

[@akshayyadur6438]

@@MechNinja okay nice

[@arshbajrang2380]

@@MechNinja man i am still waiting

[@MechNinja]

Hi...Checkout my new video of DIY 3D Printer complete build from scratch kzbin.info/www/bejne/joqwm2l6ftqgY7M

[@alpscraftshack599]

@@MechNinja I haven't seen the video of your "... replica of Ender ...". Where is it?

[@ganeshyogesh5429]

Nice video. Can you give the stl file for this printer.

[@MechNinja]

Check the video description of the video.

[@ganeshyogesh5429]

@@MechNinja Thanks for the STL files, but the y-axis rod holder STL is missing. Can you provide it.

[@MechNinja]

Hi...Checkout my new video of DIY 3D Printer complete build from scratch kzbin.info/www/bejne/joqwm2l6ftqgY7M

[@simransaifi2092]

Full price 12200

[@MechNinja]

Varies from 12500 to above....The electronic components are almost same for every printer. The cost depends on the structure of the frame. If you make of aluminium then it will be high and plastic frame will be less costly.

[@yougeshtokas]

Brillient...superb....can i have ur mail id...as i need to discuss smthing very important.

[@MechNinja]

[e-mail]