Excellent job! Really excited to see the next video!
@paulrayner45145 ай бұрын
just came across your channel, impressive work, looking forward to next vid
@FixitBuilditLoveit4 ай бұрын
I like content like this! I can not wait to see the engine runing! 🤔🔥
@wesleygoldstone47705 ай бұрын
Ace of base in the back round. Haven't heard that tune in years
@yiyongleng71575 ай бұрын
Enjoying watching, nice job!
@rbrown2645 ай бұрын
you do some pretty fine work nice job
@stewartfrye5 ай бұрын
Been watching for a while now, but this is impressive, told a few friends about your channel, Really enjoyed this one, a 10
@neillambert52693 ай бұрын
Superb do you have any plans or sizes ,would like to have a go cheers Neil
@rastafari42645 ай бұрын
very impressive! ABO placed 😉
@johnnyholland87655 ай бұрын
Amazing...
@chrischannon27395 ай бұрын
Brilliant, thank you
@alangordon33144 ай бұрын
Excellent work Sir, Could you clarifie is this the kit supplied by Hemmingways ?
@kvechannel4 ай бұрын
Thank You! Is not supplied by Hemmingways is my own work.
@ItsJoebie5 ай бұрын
everyone: you need a four jaw to make a crankshaft kve: hold my beer
@nsrvtqc5 ай бұрын
It’s kind of weird to me, it’s like watching a giant make an engine. 😂
@Mad-Duk_Machine_Werkes5 ай бұрын
It looks like the left bank of Cylinders and the right are inline with each other? the one side has to be slightly in front of the other so the rods can be next to each other and still be in the center of the bore and have two rods SHARE a journal?
@russcole56855 ай бұрын
Unless he is using knife and fork conrods, like the Rolls Royce Merlin's, Meteors ect.
@kvechannel5 ай бұрын
No is not inline, there is 2mm offset, one conrod wide. That's why I did the milling on one side of each banks looks nicer
@howardosborne86475 ай бұрын
@@russcole5685 And Harley Davidson Vee twins.
@jeffro389115 ай бұрын
The thumbnail of the video clearly shows an offset.
@howder195118 күн бұрын
Is there a drawing for this motor, or is it all your own design? Thanks, enjoyed very much!
@kvechannel18 күн бұрын
Thank You! Is my own design.. I wanted something similar to the amg m159 engine
@howder195118 күн бұрын
@@kvechannel Really good demonstration of the process of carving out the block and crankshaft carrier. I liked your technique with breaking the bearing halves like the big boys do.
@rogerleete46355 ай бұрын
Are you working from plans, or just something you came up with yourself?
@kvechannel5 ай бұрын
Yes, I had to make a plan to make everything fit
@freddygerber5 ай бұрын
Would i be able to get a copy of your blueprints.
@yankeedoodle76935 ай бұрын
you going to heat treat that crank?
@kvechannel5 ай бұрын
Would be fun but but will be just a "not working" model engine toy with the block, crankshaft and pistons only just for a decorative element for my desk :D
@larryhawkins83115 ай бұрын
Looks like you are making it with mild steel, or is it aluminum?
@kvechannel5 ай бұрын
Is mild steel block, carbon steel pistons and crankshaft and brass conrods