Valve Cover Gasket on a 2001 Honda Accord

[@jamesbrooks1183]

Glad I found this true step by step video

[@MegaMilesBen]

Hope it helps! Thanks for watching!

[@jamesbrooks1183]

@@MegaMilesBen hey my 2001 accord out of the blue started idling bad you wouldn't have run across a common problem have you

[@MegaMilesBen]

@jamesbrooks1183 many many things can cause that. Most common is usually a misfire cause by spark plugs or ignition coils. Thats the best help I can do with your information and being online.

[@jamesbrooks1183]

@@MegaMilesBen thank you

[@svoraphet1]

True mechanic right here. Great step by step! Great content, Sir! 🫡

[@MegaMilesBen]

Thank you! Thanks for watching!

[@matthewboas3776]

Thank you for the video doing the same job surprising how much oil can escape when that valve cover goes bad

[@MegaMilesBen]

Thanks for watching!!

[@Compilationsdotcom1]

I have the same car with engine oil in my spark plugs! Glad I was able to find this video.

[@MegaMilesBen]

Hope it helps! Thanks for watching!

[@leeanderson5955]

Looks good nice and straightforward

[@MegaMilesBen]

Thank you for watching!

[@scottrussell6646]

Good job. Could use some talking narration.

[@MegaMilesBen]

Ive found that most my viewers like the straight forward, no bs, no noise type thing so thats what Ive been going with. Ive considered it a few times but usually just end up putting in little notes. I started this as just a way to show some of my work to some clients but it ended up being more than that so Im still learning what everyone wants to see.

[@MegaMilesBen]

Thanks for watching!

[@th3_v0id97]

Very helpful video. Gonna have to do this on my 01 next week. Do you have a video on the poeer steering pump? Mines shot and needs done

[@MegaMilesBen]

I dont think I do for the 4 cylinder, sorry.

[@th3_v0id97]

@@MegaMilesBen what is that puller tool you used on those o rings in the valve cover itself?

[@MegaMilesBen]

@@th3_v0id97 amzn.to/3uCOGlR

[@th3_v0id97]

@@MegaMilesBen you are the man

[@Jw52013]

I am about to open up valve cover because my oil cap busted while I was removing it and a piece dropped in😩 I’m worried to turn over the engine, my brother tells me it’ll pass through but better safe than sorry to retrieve it. bc the size of it was about a quarter of inch size. This video shows me the simplicity of opening up engine. What’s your advice? Should I retrieve it or let it pass?

[@MegaMilesBen]

You havent started the car? It should be right under that valve cover then. If it were me, Id personally go in and get it. You cant get at it with some needle nose pliers?

[@alejandrogallegoslopez7729]

Are these the proper pounds for screw tigthtening?

[@MegaMilesBen]

Yes

[@arty2637]

Man that was cool... How much does that cost$$$ if you go to mechanic?

[@MegaMilesBen]

Im sorry, I dont discuss prices on youtube, there are many variations. Labor varies per shop and state and part prices vary (my clients provide their own). I am one of the lowest labor cost shops in colorado and do not charge any type of shop fees. My quotes would not compare to others. Thanks for watching!

[@jamesb.9155]

Probably about $100+ .

[@kevinlagarean4930]

What's that tool for the spark plug gaskets

[@MegaMilesBen]

Thats a Seal Puller.

[@sooolion9820]

What’s in the red spray can?

[@MegaMilesBen]

Just brake/parts cleaner. You can get cans at walmart for about $4 a can. I believe their brand is SuperTech. Its sold out quite often at my local walmart.

[@sooolion9820]

Thank you so much

[@jamesb.9155]

Hey, by the way... At highway speeds my 2000 Accord 4 cyl hunts a bit. Has fast initial pick-up but can feel the hesitation rather than smooth running at 60 and so on. Any ideas? Thank you !

[@MegaMilesBen]

That could be many things, I wouldnt be able to diagnose that for you on youtube. First obvious try would be spark plugs/coils. I always recommend oem plugs.

[@cheechsilva8827]

What size is the ratchet

[@MegaMilesBen]

The ratchet is a 3/8 drive. The socket used for the valve cover bolts is a 10mm.

[@jamesb.9155]

Good camera and microphone obviously .. but not one helpful word! I think I got what I needed though.

[@MegaMilesBen]

I appreciate your feedback, it helps me with future videos. What would you like to know that wasnt noted? Ive started talking in my newer videos but people seem to like the quiet videos better so Im considering going back to doing them like this again.

[@jamesb.9155]

A few words are always nice. You kind of get to know the person a bit by hearing their voice and by their recommendations!@@MegaMilesBen

[@MegaMilesBen]

@@jamesb.9155 thank you!

[@choepin]

What’s gasket maker?

[@MegaMilesBen]

Silicone. Available at any parts store.

[@jamesb.9155]

Is that the only kind to use? I was thinking of a gasket paste with a brush applicator. @@MegaMilesBen

[@MegaMilesBen]

@jamesb.9155 Ive never used anything like that so I cant say. Some Permatex gray gasket maker works great.