FnF45190918 - Car 013 - Valve Cover Gasket Replacement - Lexus LS 460 - Part 2
Пікірлер: 24
@luissantizo2 жыл бұрын
Thank you so much for taking the time! I know what it's like dealing the camera the extra time for editing etc. A lot of us appreciate the time you took for this. I believe there are few comments because YT requires you to create an account before leaving comments, likes, etc.
@friendnfamily90532 жыл бұрын
Thanks! It's so nice of you for understanding and for taking the time giving kind comments!
@efti7gang4003 жыл бұрын
This is a masterpiece salute my guy💯💯💪🏾
@friendnfamily90533 жыл бұрын
Thanks!
@robertlevak76885 ай бұрын
Good job hope they do mine like this tomorrow
@drewd8697Ай бұрын
Im doing my GS460 shortly. Firstly excellent job! How long did it take from start to finish? Any dinal words of wisdom?
@unamsoft2 жыл бұрын
Great Video, I am very surprised that there are over 6K viewers but only two comments. Did you have to disconnect any fuses or relays to minimize the fuel pressure on these fuel pressure pumps? Great Video!!!
@friendnfamily90532 жыл бұрын
Hi, thank you for watching and commenting. I disconnected the battery. That might help minimizing the fuel pressure.
@Knightowl9167 ай бұрын
Good video but the part I need help most is cut out ,, what tools did you use for the cover bolts closer to the wheels
@Ridikuluzt Жыл бұрын
Great video! What o rings did you replace? I’d like to do this myself as well!
@arielcastro34 Жыл бұрын
I did the same thing ,how do you bleed the air out of the fuel lines, I am not getting enough fuel its starts but it shot off when on drive pls help
@C6BlueDevil Жыл бұрын
Thanks for the video. Would a misfire be a side effect of a bad valve cover gasket? I recently changed my sparkplugs and ignition coil and the misfire is still there.
@friendnfamily9053 Жыл бұрын
Hi, I would not think so, but I might be wrong.
@jayelking2856 Жыл бұрын
yes it will. you’ll know your valve cover gasket is bad if your spark plugs and coils have oil on them. you’ll have a rough idle, low gas mileage, and loss of oil
@Xanomoros2 жыл бұрын
What tool/tools did you use for the bolts on lower part of the valve cover? I am currently doing this and struggling with the lower bolts because of the wheel hub
@dae3xt Жыл бұрын
good stuff. how did you learn to do this? youtube videos?
@friendnfamily9053 Жыл бұрын
Hi, thank you for asking. I have been working on cars for 32 years.
@rajivlaird10062 жыл бұрын
Do you have to drain the oil before doing this
@luissantizo2 жыл бұрын
No, you don't need to drain the oil if you don't want to.
@vuphung77202 жыл бұрын
Where are you located?
@friendnfamily90532 жыл бұрын
Hello Vu, thank you for asking. I am located in west side of Cleveland, Ohio.
@vuphung77202 жыл бұрын
@@friendnfamily9053 ah ok Thank you for sharing your knowledge. Great video. Wish you was closer to Texas. I would pay you to do my valve covers :)
@friendnfamily90532 жыл бұрын
@@vuphung7720 No problem! Thanks again for watching and for reaching out!
@gklove21072 ай бұрын
@friendnfamily9053 Hey my friend, how can we connect?