Valve lash adjustment .firing order 1342 4-cylinder Diesel engine .specially for beginners.

Fuel average engine performance and smooth running depends on how better your Tappet setting is.For setting Tappet on Perkins engine valve clearance the 4-cylinder process is the same.
For setting Tappet on Caterpillar engine valve clearance the 4-cylinder process is the same.
For setting Tappet on Cummins engine valve clearance the 4-cylinder process is the same.
For setting Tappet on Mitsubishi S4L engine valve clearance the 4-cylinder process is the same. The clearance might be different but the process is the same for all engines for engines firing order 1342.

[@GreatOutDoorWorldofMines]

Yes, subscribed and shared with my friends. Best video for 4 cyl 1342

[@RolandoSaquing]

What is the best gauge no.to tune up JMC engine

[@ShanEMaulaAli-fq6mo]

Thanks for sharing

[@NatePrice-uh6jb]

When i followed your instructions, #2 intake was in the open position. Perkins phaser

[@Technical.Education]

Which cylinder on valve overlap?

[@Technical.Education]

1 or 4

[@NatePrice-uh6jb]

When I put number 4 in overlap I was able to adjust number 1 cylinder intake and exhaust but number 2 intake is on the open position.

[@Technical.Education]

@NatePrice-uh6jb with number 4 in overlap adjust number 2 cylinder exhaust and adjust number 2 cylinder intake after rotating engine 360 degree this will bring number 1 in overlap condition

[@Technical.Education]

@NatePrice-uh6jb if you need help, feel free to ask

[@RamBabu-ev9wl]

Good job

[@Technical.Education]

Thank you

[@rajbahadur2162]

Good 👍 video brother

[@Technical.Education]

Thanks alot

[@Tipsonyoutubeandtechniqu-pg8oi]

Worth sharing

[@mauriceamollo8538]

What is the size of feeler gauge you're using

[@Technical.Education]

.35 mm and .45 mm

[@Technical.Education]

That’s for weichai engine intake is installed from Perkins but engine is weichai. Check your engine valve clearance according to engine manufacturer recommendation

[@LukeKundis]

Hi give the intake and exhaust clearance

[@Technical.Education]

Which engine are you working with? Every engine has its own valve clearance

[@AminaShafiq146]

❤❤

[@FourthWayRanch]

What are the specs? I have 4.236 from the 70s I - .008" E-.016" ??

[@Technical.Education]

.25 mm for intake and exhaust According to perkins, the user manual

[@Technical.Education]

www.moteur-perkins.com/uploads/catalogue/lettre/notice/manuel-perkins-ld-4-236.pdf Link for perkins user manual

[@FourthWayRanch]

​@Technical.Education it seems intake for number 4 is at the very back of the engine on mine? I am turning same direction as starter, counter clockwise

[@Technical.Education]

Find TDC exhaust on number 4 and 1 cylinder if you can find that adjusting tappets is simple

[@FourthWayRanch]

@Technical.Education I can see 4 intake manifold port is lined up with very back of engine too. Same with #2 cylinder, exhaust toward front, intake toward back Strange, #1 and #3 are intake, exh order as shown in your vid. I'll make a video. Is it possible intake exhaust order switched on some engines?

[@tenzingejang7279]

Filler guage measurement didn't mention what is the measure 0.5mm plz mention it

[@Technical.Education]

Intake .35 mm Exhaust .45mm

[@htinlinbo256]

ex? In? Please

[@Technical.Education]

Which engine?

[@Technical.Education]

Engine model and make every engine has its own intake exhaust clearance