⛐ Check out our Garage to see what tools we use and recommend: www.amazon.com/shop/worldmechanics ⛐ Subscribe and hit the notification bell by the subscribe button for new videos: kzbin.info ⛐ Our GoFundme Page: www.gofundme.com/auto-repair-guys
@mohammadaburabee49804 жыл бұрын
Why did you replace lifters? What are the symptoms of bad lifters?
@agnieszkaJanota-ej9bn9 ай бұрын
Profesjonalna robota!!! Wszystko po kolei pokazane z bardzo dobrą znajomością mechaniki samochodowej!!!!
@koltongoebel10 ай бұрын
Question? Does the 1.8l have hydraulic lifters?
@wyatte11332 жыл бұрын
Thank you so much. Shop wouldn’t even give me a price on replacing lifters and recommended engine swap…for $9k.
@oggonzalez9291Ай бұрын
Excellent video! Does this apply for 1.4L turbo?
@mehdidz41262 ай бұрын
References of valve tappet please ( the intake valve numbres, exhaust numbres) in my chevy cruze 1.8 i have: 31x --> 01 34X --> 05 35X --> 04 36X--> 02 38X--> 02 39X--> 02
@nicholasvanderwolf18032 жыл бұрын
YOUR THE BEST SIMPLIFYING THIS WORK CANT THANK YOU ENOUGH AS CARS ARE ALWAYS CHANGING THANK YOU
@mohammadaburabee49804 жыл бұрын
Why were the lifters replaced? What symptoms of bad lifters?
@RGPinger2 жыл бұрын
knocking after start. Or killed engine because lifter with hole will let valve go into piston
@plllot97133 жыл бұрын
21:38 you can't 'even hold them', you absolutely MUST hold them using a spanner if you don't want your cam ends cracked. the cam locking tool is not supposed to be used for undoing the gears. it's only for positioning the cams, it's clearly stated in the manual.
@chieftamahawk2103 ай бұрын
I have an important question about my lifters and my 1.4 L turbo Sonic I hear my lifters getting stuck occasionally shut off my car then it goes away then it comes back occasionally what's the issue do you think
@matthewking56122 жыл бұрын
Very interesting, thanks. Tell me, can going to 6500 rpm while accelerating damage these engines with 250,000 km? The oil is clean, the engine was warm. Did it about 10 times on a hard drive.
@avi-tech-haifa4 жыл бұрын
Beautiful work as always.
@razvanturcu9871 Жыл бұрын
Very good video! Thank you.
@Boyzofsummer13 жыл бұрын
What’s the average cost to replace the lifters for the 2013 Chevy sonic ? Wish you guys were located in Southern California
@zarkodanicic Жыл бұрын
To avoid confusion, state which engine it is and write its type. The fact is that the X18XER does not have hydraulic valve lifters so that viewers are not misled.
@Boyzofsummer13 жыл бұрын
Where are you guys located ?? I need my 2013 Sonic repaired. Same problems with the lifters
@RGPinger2 жыл бұрын
Does LDE (F16D4) engine 1.6 have valve lifters or not? There is in manual: Adjust valve clearance each 150k km.
@moisemarian Жыл бұрын
Thanks!
@gingerwallets80008 ай бұрын
how do you turn the crankshaft so it lines up? every video i watch they skip what to do
@AmerAmer-kn9ze5 жыл бұрын
Hello, Please I need your help. I have Mercedes Ml500 2003. The problem is the high beam working directly with low beam!!
@mattmgarza3 жыл бұрын
22:42 The black plastic sleeve on the left----apparently the clattering noise I'm getting after doing a head gasket job on this vehicle is due to that sleeve not being installed. Now I have to take it all back apart again. Do I have to fill those camshaft gears/phasers with oil when I put them back in?
@bobh86892 жыл бұрын
great job ! thank you
@robertopolizzi26844 жыл бұрын
How Many kilometers this car? My GM 18ZE meriva have 300000 km and my lifters works good
@muhdalihambal69145 жыл бұрын
Hi, can you give me the link for the special tool for cam setting. Tq.
@mikaylarunion20195 жыл бұрын
Can you provide the link that shows how to diagnose this as the problem?
@aleccooks4 жыл бұрын
A friend of mine could diagnose it my Turning the engine over once or twice to see what makes the ticking noise. But he did it with a 5cylinder
@ericwarmington5224 жыл бұрын
How many lifters are there to replace on the ecotech 1.8?
@kalenderadam86144 жыл бұрын
How many you have valve, you have lifters.
@ytsolowolf35522 жыл бұрын
It’s 2 for each cylinder
@brandonsimmons5522 жыл бұрын
On this 4 cylinder engine, 16. 8 intake valves and 8 exhaust valves
@mehdidz41262 ай бұрын
References please ( the intake valve numbres, exhaust numbres) in my chevy cruze 1.8 i have: 31x --> 01 34X --> 05 35X --> 04 36X--> 02 38X--> 02 39X--> 02 @@brandonsimmons552
@robertfric60105 жыл бұрын
Gentleman, nice video! It is GM Z18XER engine. Put there proper tag and name in the video. It will be easier to find it! I came across it by a chance.
@plllot97133 жыл бұрын
this isn't a Z18XER, they don't have hydraulic lifters, neither do A18XER. this must be something like P18XER or U18XFR.
@plllot9713 Жыл бұрын
@@dar1020 of course they are hydraulic and of course there are engines I mentioned. look it up first before commenting. I've got a z18xer, I did valve clearances in it, I know how a solid lifter from that engine looks like.
@bdog72624 жыл бұрын
Are you seriously supporting the vehicle with a jack under a cast aluminum oil pan??? Wow
@LMLFE4 жыл бұрын
B Dog he’s raising the engine up to take the front engine mount off. Not lifting up the whole car. Nothing wrong with supporting the engine like that.
@antohatriflash3 жыл бұрын
Друг, ты русский что ли?))
@lennie617 Жыл бұрын
These are not hydrailic lifters.
@dancahill91225 жыл бұрын
Like your channel and have been a long time subsciber. But you SERIOUSLY, SERIOUSLY, SERIOUSLY need to work on your accent ! PLEASE ! ! Either that or use English subtitles, which actually might be easier and/or simpler for you. I had to slow the video down to 3/4 speed to understand you ! And STILL had a little bit of a hard time understanding some words ! ! !
@nihilisticpunk245 жыл бұрын
Dan Cahill LMFAO 😂
@luislujan87154 жыл бұрын
Lmfao
@mattmgarza3 жыл бұрын
I'd like to see you learn Russian (or whatever their native language is) and start a successful KZbin channel speaking that language. If you can make a better video, do so.
@conantmasocha30753 жыл бұрын
@@mattmgarza The arrogance! I can't believe it
@bobdelabourer13072 жыл бұрын
why? he speaks proper English. I should know because I am from a former British island colony now under American control.
@nickballantyne26524 жыл бұрын
Can you give me the link on how to diagnose the lifters