Vance & Hines Quiet Baffle Review at RevZilla.com

[@tobypaone3426]

I installed quiet baffles in my mufflers simply because I was starting to lose my hearing. The quiet baffles still allow for a great sound but at a decibel rate that is lower than stock or with louder baffles. The sound difference from stock is not very noticeable but the decibel reduction is. My hearing is so much better with these baffles. I highly recommend them.

[@HarleyBreakoutGuy]

Would be nice if you had a comparison video of standard vs quiet baffles :)

[@TaylorBass]

kzbin.info/www/bejne/fqqZl2Rma793f7c&lc=z22rd31xdtfet5nwe04t1aokgmuqtwnnfanrjvwyizaerk0h00410

[@michelangelo3674]

I love these as they eliminate the crack sound and brings it to a low rumble

[@p.s8950]

I put the quiet baffles in my V&H Straightshots. can't take the noise anymore but made no difference. I then wrapped them with fibreglass, still not enough. I'm now gonna cut em in half and weld a plate in the baffle mid way down. Gotta see what it does.

[@richb.4374]

I've run my bike with and without baffles and it definitely runs better with baffled pipes. Removing the baffles will cost you some low end torque and in some cases may cause your engine to run lean. I don't need my bike so loud it wakes the dead.

[@sticksgarage7791]

Love the video and agree with you hate the idea of quiet baffles but, I am going to Germany. They have some strict laws for noise will this help? I love my staggered short shots on my 96 Softail custom Evo. Can’t beat that carburetor sound, potato potato! I would really hate having to switch them out for, gulp, stock!

[@vstar7196]

This so called “review” tells me absolutely nothing.

[@brettmccafferty465]

appreciate the video. I want better than stock sound, but I live in a neighborhood and leave fire work at 530am. I wish you had done a sound comparison with a decibel meter.

[@tomsreviews238]

Hardly any sound difference at all on V&H straight shots on Harley Sportster 48 1200. They do however give a little back pressure which definitely improves overall performance.

[@JohnDoe-cp9dc]

TomsReviews so there was not much of a difference then ? I too have a 48 and was thinking of getting these . Do you think it is worth it?

[@tuboqueser]

John Doe I have the same bike, peformance was a little lose without them, the baffles tighten up the feel of the engine and the throttle response.

[@johanros4221]

I installed the quiet baffles on a 2014 Street Bob in Big Shots staggered. I was a bit sceptic but I'm very happy with the result. They take the sharp edge of the noise and now the bike sounds great. Not quiet at all; just much more comfortable. Nice roar...

[@majdosama6561]

Johan Ros Hi John I have the same bike do we need 1 Piece or 2 for installation

[@johanros4221]

majdo sama Hi, you will need two baffles for two pipes. They don't come in pairs. And please don't take off the cling wrap!

[@majdosama6561]

Johan Ros got it thanks Man

[@mikeymixx7992]

So you just need to take the end tips off the pipes?

[@rsamraj76]

Do you think these will create any problem or impact on the fuel injection or engine and damage them in the long run? Is it required to use a fuelpak and make the correction? Please suggest.

[@theodavies8754]

3db is around 10x quieter. Removing the melted mess is no joke. For straight shots,remove the slip on. Wear welding gloves, heat them up and use the weight of the pipe as a slide hammer onto a piece of tube. I used the stand for a sunshade, aluminum tube with a plastic bung. It takes a whole load of hammering and effort. To make life easier bind the packing with stainless mig wire instead. I reckon if you use mig wire and the plastic there's a good chance they are not coming out without destroying something. Standard baffles without packing might even come out without removing the tail pipes but they're your exhaust studs.

[@cri8tor]

Recently found some used V&H Cruzers (31461) for my Shadow ACE. The baffles look like they were wrapped at one time because of the remnants of fiberglass. Like my neighbors and want to know what fiberglass wrap I should use to keep the peace? Yes, I got the jet kit. Cheers

[@zoebettina]

End cap not coming off...removed both screws...no way I can't seperate endcap without some hammering...any suggestions?

[@danielvi-dy1yu]

i have V&H slash cut slip ons ,on my 2022 Low rider st , i want better sound ,not quieter , loud is ok , any suggestions ?

[@bidgihilal8218]

Lemmy,,, Did I hear you saying it will kill the performance??

[@reganpilatzke8088]

Hi All need some advice. I have Cobra installed and find the muffler waaay to loud on long trips. I dpn't have original muffler otherwise I would return to stock. I can see the baffle inside the Cobra and was going to pull it and pack it to see if this would help at all OR, will the Vance and Hines fit, if so where do I order from

[@rogerrodales5093]

Not sure if this will be seen... but I have a Honda rebel 300 V&H but it gets too loud. Is there a baffle for my exhaust on the market?

[@Mass313_]

Hey lemmy do you lose power with these exhausts

[@jordanalbert5133]

I'm thinking about installing these but my main question is that I see they are capped on one end. is that going to take away from the performance of my bike by choking it up?

[@RevZilla]

+Jordan Albert The difference is likely to be negligible, so you shouldn't really notice much difference. -DrewZilla

[@meisterraul]

In europe they cost about 100 bucks a piece...so I made some myself ✌

[@cjdobrinski5008]

So I’ve had my 96 sportster for almost two years no the bike as been with me through a lot and is very sentimental . My landlord nologer allows me to keep it at my residence because it’s too loud. So it sits on the side of the road about a block from my house. It has stock pipes on. I would really like a new pipe that gives me that deep rumble I enjoy. But I’m looking for something that I can bolt on that will quite down enough to please my landlord, then I can easily remove it once I’m on the street. Any advice?

[@RevZilla]

The stock exhaust is the quietest you'll likely get. Even aftermarket pipes with quiet baffles tend to be louder than the stock pipes. The only thing I can recommend you do is push your bike until you're far enough away from your residence and then start it up. -DrewZilla

[@ottostapel3783]

Do I need to get the ecm reprogrammed when I installed the 21899 quit baffles

[@jjones6173]

Anyone know of something that works for a V & H pro pipe? Bought my pipe from revzilla 01/22 in 03/22 I got a chance to test the pipe sound and decided I needed to order their quiet baffle. Found out that V&H dropped the pipe and quiet baffle - V&H was no help whatsoever when I asked them for potential solutions & the guy on the phone was like talking to a politician rather than a tech support rep who gave a damn about the $1300 I had just spent on their products (pipe + air cleaner + tuner).

[@1Axis]

I'm installing the short quiet baffle without packing for the VH competition series on my Vrod. These short ones fit inside the existing baffle and require a repack of that existing baffle. How many times around would you recommend wrapping the new packing ? Thanks!

[@lildeanc]

How do you install this on a motocross bike with fmf titanium 4.1 exhaust?

[@harrycanty2929]

Love all what you do, here is my problem. I have a 2008 Suzuki blvd m109r with vances hines #18287, brought the with no baffels. Was told the no longer have that exhaust, also was told the size of the baffel is 13" long an 2 3/4 end. will you please direct me to someone that no's where I can get them...

[@RevZilla]

I believe this baffle linked below should fit your Big Shots. You would need to order 2, one for each muffler. There are also quiet and super quiet baffles available. -DrewZilla *www.revzilla.com/motorcycle/vance-hines-replacement-baffle-for-big-shots-straightshots-softail-duals-exhaust *www.revzilla.com/motorcycle/vance-hines-quiet-baffle-for-harley-metric *www.revzilla.com/motorcycle/vance-hines-super-q-baffle-for-harley-metric

[@rubo1964]

just dont like that VH charges 70each.Why not for a pair?

[@WilliamdThompson]

Dear Lenny,Thank you for the video. I'm interested in a Harley, but it has Vance & Hines Short Shots. I haven't listened to it start up yet. I like the sound of Screaming Eagle slip ons better though, but on the other hand the Short Shots baffled do sound better than the stock Short Shots to me. If I decided to go with the Screaming Eagle slip ons, would I have to buy the stock Harley pipes then buy the Screaming Eagle slip ons? Thank you.Sincerely,William

[@RevZilla]

Yes, you would need to buy stock head pipes in order to run Screamin' Eagle slip-ons. -DrewZilla

[@ad1960rag]

hey mate. is there a way to quiet this exhaust close to stock . i like the look but the epa doesnt like the sound

[@RevZilla]

+ALHD 48 Quiet baffles reduce an aftermarket exhaust a bit, but it definitely won't be as quiet as stock. -DrewZilla

[@ad1960rag]

I understand that. I purchased them . Any other options. To get a black out look with quiet exhaust?

[@RevZilla]

+ALHD 48 Not unless you can get a stock exhaust with black heat shields. -DrewZilla

[@hadipazovazquez1627]

you have four baffles .. and this video doesnt explain which one is which and which pipes they will fit .

[@seanporter108]

I was wondering what size diameter pipes would these fit in? I am thinking about getting some slash cut 40in drag pipes for my 07 softail standard. Due to my bike being fuel injected I need to have some back pressure. So I was wondering would one of these baffles fit a 1 3/4in or a 2in pipe?

[@RevZilla]

They are specifically for Vance & Hines drag-style pipes, which have about a 2" inner diameter and 2 1/2" heat shields. We cannot guarantee fit for other custom pipes though. -DrewZilla *www.revzilla.com/motorcycle/vance-hines-quiet-baffle-for-harley-metric *www.revzilla.com/motorcycle/vance-hines-big-shots-long-exhaust-for-harley-softail-86-11 *www.revzilla.com/motorcycle/vance-hines-q-series-double-barrel-staggered-exhaust-for-harley-softail-1986-2011

[@Pinozcyclezandridez]

I have a muscle, came with 2 into 1 competition series...super loud! Gotta wear ear plugs. What’s the part number for the quiet insert?

[@RevZilla]

You can find that here on our site: www.revzilla.com/motorcycle/vance-hines-quiet-baffle-for-competition-series -Zack

[@MarcioRodriguesradioriominas]

Friend, I have a V&H Big Radius 2-2 on a Midnight star, which one should I install?

[@RevZilla]

We do not currently have quiet baffles for the Midnight Star. Apologies for the inconvenience. -DrewZilla

[@024567042]

Hi Lemmy, I have the V&H twin slash slip on mufflers on my Iron 883 2015, I like the V&H sound but again it's a bit too loud. all the installation instructions I read about installing the baffles talked about removing the stock baffles but my twin slash came with no baffles at all, would I still be able to install the quiet baffles? V&H recommended 1.5in Quiet Baffle 21899.

[@RevZilla]

Yes, you should still be able to install quiet baffles. -DrewZilla *www.revzilla.com/motorcycle/vance-hines-quiet-baffle-for-fishtail-and-3-round-twin-slash-slip-on-mufflers

[@coreyk644]

Did the quit baffles help?

[@024567042]

@@coreyk644 yes they did, reduce the noise level but kept the good sound

[@GolayaPravda]

Hey I got a pair of these quite baffles from you guys for my honda vtx1800 big shots. Baffles come with fiberglass packing wrapped in plastic, do I need to remove that wrapping before installing or leave it on? Thanks.

[@RevZilla]

Leave it on! It makes installation much, much easier, and the plastic will just burn off after installation. -DrewZilla

[@Motorcyclewindtherapy]

gotta say....as easy as these are to change....I'm gonna grab a set of the quiet baffles for long rides on the Softail with the Straight shots...and leave the 'naked' louvered baffles in for the town riding and overall crazy loud for safety aspect. thanks for a great Vid, sir!

[@scottparrish5992]

Any way to know which of these will fit a 2-1/4" OD pipe? Trying to shush Supertrapp Mean Mothers pipes on my Dyna.

[@RevZilla]

These aren't designed to fit Supertrapp exhausts unfortunately. -DrewZilla

[@HarleyBreakoutGuy]

I need a set for my 2017 harley breakout with vance and hines short shots staggered but i cant find the quiet baffles on your site, please give me a direct link to buy thanks mate.

[@RevZilla]

Here's the direct link. -DrewZilla *www.revzilla.com/motorcycle/vance-hines-quiet-baffle-for-harley-metric

[@tomsreviews238]

Its almost impossible to tell the difference between V&H Standard and Quiet baffles sound. They do however give a little more back pressure and lessen the backfire.

[@antonio7334]

which lessen the backfire and such?

[@tomsreviews238]

@@antonio7334 quiet baffles do

[@pvtepile]

Hi I have twin slash staggered on my vn900 custom neighbour complains about the noise which would fit my exhaust system out of these in your video

[@RevZilla]

Here is what you need. They're sold individually, so you'll need to order 2. -DrewZilla *www.revzilla.com/motorcycle/vance-hines-quiet-baffle-for-fishtail-and-3-round-twin-slash-slip-on-mufflers

[@richardredpath5032]

Hey bro, love you work. I have been issued a defect notice on the noise of my exhaust. i have vance and hines 2 into 2 big radius which you mention they dont make the quiet baffles for. do you know if there is anything else out there on the market that can quieten these bad boys down? thanks in advance!

[@RevZilla]

The only way to quiet them down is to take it a bit easier with the throttle...or swap those pipes for a set that uses baffles. That's the hard truth. -DrewZilla

[@markwells8212]

I recently installed the 2 into 2 big radius on my bike and noticed that you have a baffle for these pipes on the site now (www.revzilla.com/motorcycle/vance-hines-big-radius-quiet-baffle-for-harley). Would you recommend against those baffles or were they not available at the time of this original post?

[@cookingwithsamontheblackst3282]

mine still a little loud but a deeper sound

[@TheKenthor]

I'm curious. Would installing these require an ECM change?

[@TheKenthor]

***** Cool. An answer form the famous Lemmy himself. Thank you, sir.

[@DrSandman90]

Meanwhile there is an option for the big radius! Just ordered it 5 minutes ago at RevZilla :-)

[@arnaldo18]

Do they make them for Competition 2 into 1 (Low Rider S)? I've been looking, but can't find anything...

[@RevZilla]

Vance & Hines does make a Competition Series 2-Into-1 exhaust that will fit your bike, and I included a link below. -TeamZilla AJ *www.revzilla.com/motorcycle/vance-hines-competition-series-2-into-1-exhaust-for-harley-dyna-2006-2016

[@sarnaldo6602]

I already have the V&H Competition 2 into 1 exhaust on my Low Rider S. I was just asking for a quiet baffle.

[@RevZilla]

We carry the baffles on our site, and I've linked them below. -TeamZilla AJ *www.revzilla.com/motorcycle/vance-hines-quiet-baffle-for-competition-series

[@nileyocke1335]

Is the difference in air flow enough that I will have to use my FP3 to redo the efi?

[@RevZilla]

It's not a big enough difference to warrant the FP3. -DrewZilla

[@nileyocke1335]

RevZilla thanks

[@Nichols9431]

YES

[@Dgoff11]

@@RevZilla hey I got a question if I remove the Baffle will I need a tune?

[@stormman8393]

You're a legend Lemmy great info

[@nsajgalvan]

Have you done a db test with the pipes stock at idle and then say 3,000 RPM and then compared that to the Quiet Baffles at idle and at 3,000 RPM and the Super Q Baffles at idle and at 3,000 RPM? I've listened to many KZbin videos that have these pipes. I wonder if the people recording set the audio to manual so the device does not increase or decrease volume. Anyways I'm looking to get the Short Shots for my Street Bob and am contemplating if I want the Quiet Baffles or Super Q Baffles. Good video and great reminder about fiberglass!

[@RevZilla]

We have not done a scientifically-controlled test as such. In practice, I don't find the quiet baffles to be that quiet at all. Only the Super Q Baffles make much of a difference to me. -DrewZilla

[@timn4481]

@@RevZilla i find that the fact that you dont do a proper, non subjective test, is disappointing. Thankfully someone else did and measured the difference. it would really help if companies made an attempt to be objective in products because you cant dispute facts. noise readings wouldve made this video useful. As it is, its not really that useful. Plenty of places have baffles- why would i buy the Revzilla one?...cos you said it sounded cool?..

[@delwynburrows]

Ive just installed Super Q Baffles on my 883 Iron, and have lost serious power and its popping. It is going back to the shop.

[@gtx332]

These things are just about impossible to get out once installed. They deepen the sound and sound good but they certainly are NOT quiet.

[@Nichols9431]

Just installed mine. I took dB readings of stock mufflers, V&H 3" Twin Slash muffler with stock and quiet baffles. Readings were as follows. Stock mufflers--83 to 86 dB. V&H 3" Twin Slash muffler with stock baffle--104 to 107 dB. V&H 3" Twin Slash muffler with quiet V&H baffle--94 to 97 dB. The quiet baffles are still loud enough to be heard better in traffic, have a deeper throaty tone, and are under the 100 dB noise ordinance standard in my city.

[@timn4481]

@@Nichols9431 best.reply. in. the. thread. thank you.

[@edviniusuf9130]

which one is VHA406R-R for double barrel V&H exhaust ? thanks

[@RevZilla]

+Edvin Iusuf That part number is for European stock, so I cannot cross reference that to a US part currently. -DrewZilla

[@WilliamdThompson]

Thank you for your reply, Lenny.William

[@Afoggsunshine71-4]

What is the 'trick' to getting the original baffles out ???

[@HarleyBreakoutGuy]

ride the bike around till the exhaust is hot it will make the baffles come out really easily.

[@ellerskillzis]

Spray some WD 40 inside and let it sit for a few minutes. Then grab the baffle with a pick tool available at Harbor Freight for a cheap price. Good luck!

[@timn4481]

coat hangers work well. bend one so you can grab the baffle from inside.

[@gregoriojuarez1579]

Is there a baffle available for a stock 2017 Harley Davidson Superlow 883

[@RevZilla]

Our focus is really only the aftermarket. If you're looking for a baffle for a stock exhaust, you'll likely need to source that from Harley. -TeamZilla Chris

[@MrBinggy]

Are there different baffles for the V&N Slip-on pipes or are these only for full system exhausts? And assuming the only change i make on an Iron 1200 are these slip-on pipes, Will the bike run fine if I don't do a re-tune? Thanks

[@RevZilla]

There are different baffles depending on exhaust diameter and whether the exhaust is a big radius style. If you're just doing slip-ons on an Iron 1200, you do not need to retune. See below for the available Vance & Hines slip-ons and compatible baffles. Remember that baffles are sold each, so you'd order 2; one for each slip-on pipe. -DrewZilla 3" Round Twin Slash *www.revzilla.com/motorcycle/vance-hines-3-round-twin-slash-slip-on-mufflers-for-harley-sportster-2014-2017 *www.revzilla.com/motorcycle/vance-hines-quiet-baffle-for-fishtail-and-3-round-twin-slash-slip-on-mufflers *www.revzilla.com/motorcycle/vance-hines-competition-baffle-for-fishtail-and-3-round-twin-slash-slip-on-mufflers 2 1/2" Straightshots *www.revzilla.com/motorcycle/vance-hines-2-12-straightshots-hs-slip-on-mufflers-for-harley-sportster-2014-2017 *www.revzilla.com/motorcycle/vance-hines-quiet-baffle-for-harley-metric

[@HarleyBreakoutGuy]

could i pack my current baffles with fiber glass ?

[@RevZilla]

It would be a pain to try to pack your current baffles, but you could try. -DrewZilla

[@cookingwithsamontheblackst3282]

not enough room for the glass

[@HarleyBreakoutGuy]

ok thanks for the reply

[@apumountainguides]

Wich one is for v&h 2 46065 big radius. Thanks .

[@RevZilla]

This one. -DrewZilla *www.revzilla.com/motorcycle/vance-hines-big-radius-quiet-baffle-for-harley

[@frankidm695]

Love this guy

[@a.aseeri5265]

Hi Lemmy, I have V&H short-shot installed on my 2011 street bob.. I'm considering Quiet Baffle due to laud noise I'm casing my neighbors.. Therefore, the following are my few question about those quiet baffles: 1- Is there major difference between the V&H Quiet Baffle vs Super Q Quiet Baffle? 2- From the pictures i saw and some of reviews i read, it seems that 'Super Q Quiet Baffle' might require some modification to be made on the short-shot in order to fit it, am i right? 3- while configuring Fuelpak FP3 it asks me for the type of baffles on the exhaust however, in Fuelpak FP3 there is no Super Q Quiet Baffle option, therefore, what shall i chose in the app when tuning and will that have an effect on the tuning? 4- While installing the Quiet Baffle or Super Q Quiet Baffle will i have to use anything other than the "L Key" to be able to slide in the baffle screw it again? look forward to hearing from you mate.

[@RevZilla]

1. Yes, there is a major difference between the Quiet and Super Q Baffles. The Quiet Baffles aren't that quiet, while the Super Q Baffles make the Shortshots acceptably quiet at idle and low speed. You still get a nice full sound when accelerating though. 2. The Super Qs should not require modification. 3. With the FP3, you would just choose the standard baffle option. You can then run auto-tune mode if you want additional fine tuning. 4. You don't need additional tools, though you'll probably want to use some anti-seize on the metal flange of the baffle, just where it mates with the exhaust. Also remember to leave the thin plastic wrap on the baffle material for easier installation. -DrewZilla

[@HarleyBreakoutGuy]

does it really work?

[@RevZilla]

Yes, it really works. -DrewZilla

[@boualaybounma8330]

How many decibels is the noise reduced by?

[@RevZilla]

These quiet baffles generally reduce noise by 2-3 decibels. -DrewZilla

[@franciscogomezleo9535]

RevZilla is the performance go down?

[@AlanTrades]

Do you gain torque with the quiet baffles?

[@RevZilla]

You might increase torque ever so slightly, but you probably wouldn't notice it. -DrewZilla

[@theduke723]

do they fit the vh shortshots for a 09 nightster?

[@RevZilla]

Yes, you would need the following Quiet Baffles for your Staggered Shortshots. They're sold individually, so you'd need two. -DrewZilla *www.revzilla.com/motorcycle/vance-hines-quiet-baffle-for-harley-metric

[@sooddthisman]

would they work for the HD street 500???

[@RevZilla]

+mr Turner No, these are not designed for the Street 500 and 750. Vance and Hines makes the Competition Series Slip-On for the Street 500 and 750, and that slip-on includes a removable noise insert. However, even with the noise insert in, the exhaust would be louder than the stock exhaust. -DrewZilla *www.revzilla.com/motorcycle/vance-hines-competition-series-slip-on-muffler-for-harley-street-2015-2016

[@cookingwithsamontheblackst3282]

mine runs better moore back pressure

[@williammorgan5987]

I happen to own the loudest Harley I’ve ever heard in person. And is confirmed by everybody I ride with. And it’s not good. Either I ride back of the pack or the other guys stay far behind me, it was reported to me that every time i passed a car people held their ears which meant weren’t holding the wheel. I ordered the super Q.... damn I’m getting old. When I want to shoot flames again they will be easy to take out

[@shobud7561]

There baffles are totally worthless , theses damn V&H pipes can not be quiten down !

[@vaughndrew852]

Yes much better than the original baffels in my long shot staggerd befor it was cop bait and just sounded like a wanker now with qiuet baffels it has a much deeper solid sound with out the annoying open rumble that frankly sounded fucked

[@TheVelvetsky614]

I watched the whole thing for the before and after demo I KNEW would be there. Not so much....

[@cookingwithsamontheblackst3282]

they sound good

[@darrellmount7020]

why don't you just go back to stock, in most cases it sounded just as good anyway.

[@Plumbermark]

Have you thought about getting rid of the wife instead of the exhaust ?

[@cookingwithsamontheblackst3282]

on my short shots

[@msg63bretired82]

Butt dynos are seldom accurate.

[@jbtwinscrewed]

No sound comparison. Waste of time.

[@zoghunter82318]

Most useless video ever...

[@Cdlzzl]

Would the these help to increase bottom end torque. As in the case of sideshots installed on a tc96?

[@gnarlytothemax]

performace gain down low?

[@kentsimon9400]

Ever look into torque cones?

[@Nichols9431]

YES.

[@timn4481]

no. and if you've mapped your ECU you might want to re-map. thats if you notice anything.

[@NZ2STROKE]

I have a 2001 dyna tsport with long shots,which baffles will fit?