Chev utility 1 4 - Front wheel drive clutch fitment.

[@sithembisoduze8728]

Glad to see locally made tech video, well done

[@vehiclemaintenanceandrepai3790]

Around R6500

[@nutlange6910]

Lovely little bakkies these. I had one in which I did 256000 odd km`s in about 4 years.. Neva skip a beat and drove pretty much all over SA in her.. Nice video again, thx Gary

[@craigrodgers3691]

Keep the good work up. Thanks for taking the effort to help others.

[@pietercoetzee2848]

Whats the torque specs for the pressure plate?

[@clintdarocha4159]

Thanks for your videos. You've really helped me to understand the clutch replacement.

[@sathasivanmurugas8639]

Very informative video Gary. Thank you

[@vehiclemaintenanceandrepai3790]

Thanks for the continued support, Sathasivan

[@AccordCL9-ZA]

Hi Gary. Very good video. I was just wondering.. what are the torque specs on the clutch plate and flywheel?

[@sizwenhleko866]

Very informative thank you very much

[@vehiclemaintenanceandrepai3790]

Thanks for the support Sizwe

[@dewalddewet759]

Baie dankie. My cbakkie se clutch kit is in, en alles werk perfek.

[@moffatk7948]

Hi Gary, welldone, nice to see proudly SA video, explained so eloquently. My opel Astra J 1.4 T clutch failed today, I suspect the thrust bearings. I wonder if it will be very different from this. I intend to do it myself, I'm adamant I will get it right any tips and suggestions will be appreciated.

[@TheGapedi]

Thank you for a very informative video. I am in Table View and need to take my 2012 Chev Utility 1400 in to service the gearbox which is leaking quite a lot of oil from the inner sideshaft seal. I need to do an urgent trip from Cape Town to Mossel Bay (to build a large fish tank) and back and need the Chev attended to quickly, professionally and at the best possible price... I am on a very tight budget. Do you have any recommendations?

[@houtbay7343]

WONDERFUL VIDEO ITS EASIER TO RELATE WITH THE AFRIKAANS ACCENT

[@vehiclemaintenanceandrepai3790]

Thanks for the support, local is definitely lekker, hahaha. Gary

[@mphoramokolo361]

Nice and very informative

[@matomemilfordmojela9391]

What Model and Year is this

[@AlbertusvanTonder]

Hi Gary. Thank you for this video as it's extremely informative! This may be a dumb question but how do you check that the gearbox oil is at the right level and what's the best way to top it up? Any feedback is appreciated!!!

[@vehiclemaintenanceandrepai3790]

On the passenger side of the gearbox, there is a 13mm head bolt, this is where one fills the gearbox with gearbox oil, the car must be level though.

[@haprocreativesmedia7584]

Greetings, what causes a car to vibrate in great 1 after a clutch replacement? My machenic said its normal for it to do so.

[@shabeermohamed2193]

Hi I have a utility gamma shape have to leave clutch right to the top befire it moves, there's no leaks we have blead the system, I think it's the fingers gone cause pedal is soft and don't need to to push all the way down. What do you think, thanks

[@vehiclemaintenanceandrepai3790]

If the clutch is functioning well then leave well enough alone until it really needs replacing.

[@LunganiMemo]

Hi, happy to see a local video.. Where is your workshop? It might be worth the drive to have my car worked on by you guys

[@vehiclemaintenanceandrepai3790]

Thanks for your visit, support, and response, Lungani, I am in the Southern Suburbs of Cape Town.

[@Mozamiel78692]

Hi my reverse lights not working please advise CHEV utility 2014 I have checked the switch it works Please help thanks

[@vehiclemaintenanceandrepai3790]

Check the globes itself, the circuit fuse for the reverse light circuit. Failing that consult an Auto Electrician as it could be a fault in the wiring lume.

[@etienneprinsloo1171]

@@vehiclemaintenanceandrepai3790 hi there.. I would just like to find out how to remove the glove compartment door on a chev utility 1.4 2017. Please I don't want to break anything there.. Thank u

[@vehiclemaintenanceandrepai3790]

Hello Etienne, I have never had to remove one myself, check this video and see if it is the same, it may help, kzbin.info/www/bejne/fXLRlalteNx-pM0 let me know how it turns out.

[@vukanihlophe6295]

So how does the clutch get to be termed high or low on these

[@vehiclemaintenanceandrepai3790]

Please explain more I do not understand your question.

[@marklewis4793]

thanks,

[@gawieniemand9237]

how to put the thrust bearig

[@user-cz8yq7fz5j]

Hi i am a proud owner of 1.4 Chevrolet Utility, its got 180000kms on the clock and makes a rattle noise when pulling of in 1st gear. I it possible that it could be clutch and it needs to be replaced? the clutch has never been replaced before

[@vehiclemaintenanceandrepai3790]

Not necessarily, E, it could just be a loose bracket on the exhaust, at 180000 km it is not usually necessary to replace the clutch it last well into its 250000km range. If the gear selection is not affected and the clutch does not slip then it is highly unlikely the clutch is faulty or needs to be replaced.

[@sandilesithole3660]

Hi Gary, the center nut for the cv joint, you pre loosened it, what is the method you used there since it is actually pinched to lock it in position?

[@vehiclemaintenanceandrepai3790]

Hi Sandile, I used a normal Power bar while the car was on the ground the lock is broken with a small amount of force by using the power bar and the right sized socket, I do explain it in the video 3:37 min.

[@sandilesithole3660]

@@vehiclemaintenanceandrepai3790 Thank you, will try it out again, need to replace the front wheel bearings. is the nut reusable after or must I get a new one

[@vehiclemaintenanceandrepai3790]

it is reusable Sandile we re used those in the video.

[@Puledisipho]

Hello how much to fixing clutch labour and clutch kit

[@Puledisipho]

Some model Chevrolet utility 1.4

[@craigvinnicombe]

I have 2013 Chev Ute 1.8 (given me nothing but kak). It has started a whining noise only under acceleration. Only happens in 2nd and 3rd gear. Car shifts fine and goes perfect. When you are not accelerating it does not whine. It is a work vehicle so it is often loaded. Have you had any experience like this with other cars? If so what was the problem? Kind regards Craig

[@vehiclemaintenanceandrepai3790]

Thanks for visiting my channel Craig, it sounds like the main shaft bearings are worn.

[@owamemonthati6970]

What happens when its not going into gear?

[@vehiclemaintenanceandrepai3790]

A faulty Pressure plate or the clutch is not adjusted correctly, the selector cables could be fitted wrong too. The clutch fork could also be damaged (bent)

[@JN-mc1jk]

My clutch pedal feels loose all the way down, after replacing new clutch kit.

[@kswisssaidi7397]

Hello how are my chev utility is hard to shift in gears please help

[@vehiclemaintenanceandrepai3790]

If it is not the clutch assembly Kswiss Saidi then it could be the selector cables that is worn. Gary

[@nardusellis655]

Hi Gary I have a 2010 Corsa Utility 1800 old shape. Hydraulic slave cylinder leaking.....fluid coming under bell housing. Shopping around for repair manual. I'm not a mechanic so need some help.... Greetings

[@vehiclemaintenanceandrepai3790]

Hi Nardus, thanks for supporting my channel with your visit and interaction, unfortunately, the gearbox must be removed to access the concentric clutch slave cylinder.

[@nardusellis655]

Hi Gary Thank you. ... came right....by loosening the four bolts and steering bolts. Dropping the substrate....controlling it with a jack. Gearbox moved away to replace the CSC without dropping it completely. Job done and going. Thank you for your advise. Nice day from Darling WP

[@vehiclemaintenanceandrepai3790]

Glad you aced it Nardus.

[@elliskauesa8488]

hi, can someone please help me with my chev utility. when you engage gear one and then trying to leave clutch slowly it vibrates. what could be the problem?

[@NathanealGovender]

Did you find out what the problem was?

[@haprocreativesmedia7584]

I have a similar problem. Did you find a solution to yours?

[@elliskauesa8488]

Just change clutch kit

[@Bruei]

Awesome work🤞

[@vehiclemaintenanceandrepai3790]

Thanks for the compliment and support, Jones

[@maxxila9745]

How much is clutch kit ?

[@vehiclemaintenanceandrepai3790]

Hello Max thanks for supporting my channel with your visit, clutch kits vary from R1200 - R3000. depends on the model, quality and where you buy it. try Midas. from Gary

[@JN-mc1jk]

Your tie rod ends are finish. They are 1300 dollars at Auas mototmrs.

[@JN-mc1jk]

Nope 13 thousand

[@sheldonsuklal1025]

Steps missing

[@vehiclemaintenanceandrepai3790]

Thank You for supporting my channel with your visit and interaction, I am pleased this video was helpful to you. Please feel free to check out the rest of my channel by clicking PLAYLISTS www.youtube.com/@vehiclemaintenanceandrepai3790/playlists for more helpful service and repair videos on most makes of cars available here in SOUTH AFRICA, It is FREE.