Victron Energy Off Grid System | Easier Than You Think | Part 1

[@simonsays6557]

I have victron off grid system. Haven’t burnt a liter of diesel by the generator since I installed it

[@CountryLivingExperience]

Nice!

[@blainecelestaine4543]

I know this was a year ago and you've already solved the issue but if cut a slot the length of the wholes in the inverter in the wire trough and screw it to the wall tight to the bottom of the inverter , you don't need conduit between the two and it will pass code. . You still have to protect the wires as they enter the inverter but it's easier.

[@morrismaneae3634]

I would prefer using square duct instead of conduit❤

[@richardc3208]

Not in my budget for sure, but from the research I've done they are probably the most efficient. Id run my wiring however I wanted especially being off-grid and not connected to the main structure. Too many rules and not enough truth now a days.

[@clarencewiles963]

Looking forward to seeing the results. Thumbs up 👍

[@CountryLivingExperience]

Thanks Clarence

[@carnaud]

Thanks for your content! Good stuff!

[@CountryLivingExperience]

You’re welcome

[@dmark6699]

Installation looks pretty professional. A lot of places like where I live have more regulations than just the NEC.

[@CountryLivingExperience]

Thank you. Luckily I am in Texas out in the countryside

[@CountryLivingExperience]

@@UKsystems Lol!

[@CountryLivingExperience]

@@UKsystems Bye troll

[@AdamDeLayDIY]

Thanks for sharing Eric. I ran into the same conduit fitting issues when I installed my Multiplus-II 5kVA inverters. I ended up grinding down some of the threads on the fittings to barely, and I mean barely getting them to fit. It would be nice if they did accommodate for conduit connections. I completely agree though, it can look like a complicated system just because there’s more components, but I do think it’s a very easy install. Looking forward to the next part! Thanks!

[@CountryLivingExperience]

Thanks Adam. Impressed that you were able to shave down those threads and still get the locknuts on.

[@AdamDeLayDIY]

@@CountryLivingExperience haha…so was I. I did find out that the holes are so close together though that it was difficult to get the lock nuts to tighten down.

[@CountryLivingExperience]

Yep, same. Even with the 1/2” connectors.

[@ALuxeLife]

Is this just for AC for the chickens? What else do you use it for?

[@CountryLivingExperience]

It is used for the entire barn behind the chicken coop. Power tools, lights, well pump and just pump.

[@rodneyross5282]

CM??? I was brought up with American inches not European crazy measurements lol. I like the victron system, However, I will stick to my good ole EG4 system not so much wiring. Have a super blessed Sunday.

[@CountryLivingExperience]

Lol. Yea, these inverters are from the Netherlands. I think I put text in the video mentioning 4 inches. Just showing options for y’all. Blessings.

[@TheKallipugos]

For 4g sheathed cable, you can get it. Look for 4-4-4-6. Big box stores only carry in full spools so go to a local electrical supply.

[@CountryLivingExperience]

Thanks for the heads up

[@Electronzap]

Awesome project and good explanations.

[@CountryLivingExperience]

Thank you

[@iSkiDoo2023]

I watched everything you did and I disagree that what you did was easy. 😂 if I do any solar, I think I will stick with an all in one like the 18k or similar which actually seems easy. Nice thorough explanations though.

[@CountryLivingExperience]

Lol. It is easy. I mentioned why I am using this system for this application in the intro video to this series. I love the 18k but it will not work for this type of setup.

[@George_us]

Hello, What is the model number of the air-conditioning unit that you are using in your shed? Thanks

[@CountryLivingExperience]

Not sure. It’s an LG. Just grabbed the smallest one they had at Home Depot.

[@mondotv4216]

You don't need conduit for your low voltage wiring. You can buy double insulated 2.0 cable of your concerned but if it's 24 or 48V there really isn't any danger of electrocution.

[@tlteal]

I have the Victron 450/100 and the Cerbo GX and looking to move away from the Ecoflow Delta Pro and smart Home panel but not sure what else I need to add to the system. Basically what victron piece can replace the Ecoflow Smart Home panel? Is that the multiplus?

[@CountryLivingExperience]

Looks like the EcoFlow smart panel is just a glorified sub panel with a transfer switch. The multiplus will be the inverter that you need, yes. That will replace the Delta pro.

[@tlteal]

@@CountryLivingExperience correct, the smart home panel is a transfer switch with some smarts in it. the ecoflow delta pro is a battery, MPPT and charger all built into one. I'm trying to move away from their ecosystem one piece at a time and move to the Victron system. BTW, thank you for the kind reply! So I would need one of the multiplus II ? i noticed they have 8k and 10k version..... is that new since the 5k?

[@CountryLivingExperience]

@@tlteal You're welcome. I don't know how much power you need for your house so I can't recommend a size of Multiplus inverter for you. Also, do you need 120/240 or just 120? How many panels do you have? What batteries will you connect? There is a lot to figure out before suggesting something. Is this just a backup system or do you want to go off-grid full time?

[@tlteal]

@@CountryLivingExperience Very fair. I already have plenty of battery backup. Around 20kw worth. I think I just need to add the multiplus II or two of them and I'll be good. Thanks.

[@amsohn1]

Thanks for sharing! Blessings ❤

[@CountryLivingExperience]

You’re welcome

[@brentjohnson6654]

Thanks for the video. Are you replacing the EG4 6500 with this Victron system?

[@CountryLivingExperience]

You're welcome. No, this system is for the barn, well, and jet pump. I needed a more customizable system for those loads that could work off a small amount of panels.

[@brentjohnson6654]

@@CountryLivingExperience thanks. Fast response. I am in the middle of your video. I like the Victron approach for repairs (not all in one units). I know it is much more cost with them. Had you looked into Sol-Ark in the systems you have done (EG4 or Victron)?

[@CountryLivingExperience]

@@brentjohnson6654 Systems with different components are much better for repair for sure. Luckily Victron products are also almost bulletproof. I still like my EG4 system in my house and the Growatt's that I had before. I never looked at SolArk initially because of the high cost. I have friends who have them and like them though.

[@Akdale777]

Great videos. I am down to Victron and Schneider as my choices. Did you by chance look at Schneider as well. Curious on your thoughts.

[@CountryLivingExperience]

Thank you. I couldn’t really find Schneider products to fit my needs. Additionally, They are physically very large.

[@herbertvonsauerkrautunterh2513]

Doing it hard.. get a plastic box. Cut holes to suit and screw the box right in under the unit and run your confuit into the box and wires into the unit.

[@rusty-y8r]

a diagram of your set up would be nice

[@CountryLivingExperience]

My videos are the diagrams and instructions. I have 42 diy solar videos.

[@mikeremillard5414]

newbie investigator on going off grid why Victron ? is it the latest and best

[@CountryLivingExperience]

Victron is actually a brand that has been around for a long time. They are tried and true and extremely reliable. It is one of the best.

[@mikeremillard5414]

By early next year I would like to build a solar system for added use to my home, I use about 1800 kwh here in south Mississippi how big of a system should I start with and I agree on starting out with Victron . My other question is can a solar system be shared with two homes

[@CountryLivingExperience]

@@mikeremillard5414 So you are using on average 60kWh per day. The size of system will depend on your budget. Do you want to start smaller and add over time? Do you want to go off-grid, want a hybrid system, want to be totally grid tied? There are so many questions you will need to answer for yourself first. Is the second home included in that 1800kWh? A second home could be added but it will be more complicated electrically and would need an electrician to sort that out because you would have two main service panels to deal with.

[@mikeremillard5414]

thanks for the input ..I plan on starting small with the ability to expand in the furture, on the second home that would be of later in the plans right now Im a newbie and gonna set myself up@@CountryLivingExperience

[@mikeremillard5414]

What brand solar panels did you go with and whats the KW

[@JenkinsUSA]

Just curious, I’m a solar noob. Did you consider a EcoFlow Delta Pro for this project? It’s plug and play. I bought two EDP, a smart home panel, a dual fuel generator and 4K of EcoFlow panels 400w x 10. Ground mount from signature solar, based on your recommendation. I’m loving it so far. 😊

[@CountryLivingExperience]

Hello. Glad you are liking them but no I didn't consider one of those. While they are simple, they are not that powerful for running anything more than emergency loads for a short time. The battery life is just too short and they would not handle the loads that are in my barn....well, jet pump, table saw, chop saw, 120v welder, etc.

[@BNOBLE.]

I cant wait until solar pays for itself.

[@bruceeverett5372]

Nice video. I do have a couple questions-- Are these inverters programmed to produce a 240v supply? Without an AC input you won't of course have the "grid assist" feature so you're really have 6000VA, (actually 4800 watts total due to the deceptive Victron PF ) So I'm wondering why the 4 gauge output wiring. Are you using 4awg for a specific reason (super long run) or did you just have a lot of it already? Victron makes really great and durable stuff, buy once, cry once!$$$ Looking forward to seeing the 'project completed' video soon! You make excellent videos.

[@CountryLivingExperience]

Thanks. Each inverter is 120v so you need two of them for 240v split phase. I have a very long run from the inverters to the main panel in the barn so I am trying to limit losses in the line with the 4awg.

[@mdinning123]

Did you happen to evaluate using the Victron AutoTransformer in step up mode from 120v to 240v versus installing two Invertors? @@CountryLivingExperience

[@CountryLivingExperience]

@@mdinning123 I didn't look into that. I worked with the Victron designer at Signature Solar and he recommended the two multiplus's for the loads that I have.

[@Levitesamuel]

How much is victron system

[@CountryLivingExperience]

It depends on the components you need. Every system is different. Mine was $6000

[@davidoneal4132]

Maybe you can help me I'm looking for someone that can help me install my small solar power system that I have on my box van I need someone in Washington that's familiar with a viltron energy solar charge controller and distributors going into a 48 volt inverter it has 5 solar panels on the roof each are 370 watt for as total of 1850 watts all together. So do you know anyone in Washington state that can accurately hookup this system???

[@CountryLivingExperience]

I don't know anyone. I make these videos to help people do it themselves. I don't do vans or rv's either. That is a separate skill and knowledge. There is a channel called Explorist Life who does Victron for rv's. Check him out.

[@veteranveteran9915]

I'm so jealous I have a few victron pieces but that's got to be $5k sitting on your wall right there. One day...

[@CountryLivingExperience]

You’ll get there. They are the Ferrari of inverters so they are a bit pricey.

[@micklipscombe8614]

Victrons not complicated it’s just expensive so people like me can’t afford it 🙁

[@CountryLivingExperience]

They are expensive. I also have the EG4 in my house which is a lot more affordable. Have you seen my installation videos on those?

[@dutchminer247]

Easier Than You Think... "PART 1" 🤣