VIFLY Short Saver V2 - No More Magic Smoke

[@KremerFPV]

I highly recommend this device as well as it has definitely saved me a few times.

[@MadRC]

I have tried to kill it but I can’t lol.

[@olibpics]

You can also use this also for the binding of the receiver

[@typxxilps]

I might have missed a video and had thought that this video would have been about the successfull rescue or repair of the dji air unit. Therefore I´d like to ask if the magic smoke finally had killed your air unit or are you still waiting for that missing part, that second regulator from china ? that being typed right now I guess you answered it with the final tiny sentence at the end of the video ... others might have overheard. Good cliffhanger to keep the hope alive ... and I'd loved to see you to succeed in this mission.

[@fpvnme4845]

great bit of kit essential in building

[@Rip1Outdoors]

The captions called it an “ear unit”. That’s funny stuff. Good job Ian

[@MadRC]

Yea my accent does that lol.

[@Rip1Outdoors]

@@MadRC you should hear my Mississippi USA accent 😂

[@sUASNews]

I bet you can push it to its limit. Your our blue smoke hero.

[@MadRC]

Iv tried and failed so far lol.

[@quadswithmods]

Good job mate i need these 2 😅

[@GeorgeCooper_LoneWolf]

Great review. A must-have for any RC work bench. As you mentioned you weren't sure whats the difference from the V1. The V1 does not have two buttons but it does have a small dip switch to change from 1Amp to 2Amp but you can't adjust the current level.

[@MadRC]

Thanks that’s great to know. Tbh I forgot to go look when I was filming and never addressed it again lol.

[@abdulwadoudalikhwan2617]

we are using a 6s 22.2v lipo battery that has 32000 mAh. When plugging in the vifly v2, we at low sensitivty ( 3 blinks) and 2A. The device is shutting down at almost 30% power. This might be due to a false alarm. What are the possible solutions.

[@TheMrjogas]

What happen if connect 10s not 6s

[@mertkaptan3849]

ıt just cuts off when i give some power on the motors. my setup is 2207 supernova motors 65a esc and 6s lips. I select the three yellow led set for low sensitivity and high current and 2 amp mode. ıt works but when i put on the throttle it cuts off. why do you think it is happening

[@MadRC]

It's not designed to allow the drone to run. It's simply to protect a short on startup. It's only rated for 2A. As such once you know your drone is safe you don't use it to test with the motors

[@Sir_Hubris]

very clear explanation, thank! ¶ :-)

[@ndtran9913]

It doesn't work with 1S whoop. How do I test with 1S whoop.

[@NordyFPV]

Maybe make a connector from ph2.0 to xt30?

[@Secret1one2]

Such a nice little thing. A bit of a shame they didnt put it in an enclosure of some sort and just heatshrinked it. I guess it'd be possible to make a little case for it to 3d print.

[@typxxilps]

There are 2 points: to have a rescue belt and to use it you have to get one and you have to get used to use it as a habit and that is a long way to get there even though you had such incident that became an accident to remind you we all have fuses even though we tend to ignore to use them like to obeye rules that are even usefull cause we blieve to be in a hurry or we might think we do not need it for such tiny project till magic smoke sends his greeting from eternity. But I will get one for sure and hope that I will recognice when it kicked it even though I would appreciate if that V3 that might be coming up would have a kind of small buzzer noise instead of only that orange light which could be red too