VOTOL EM260 /2 - Instructions for fixing Read-Only Busbar / Sport Current

[@tylormack]

This helped me IMMENSELY. thank you so much

[@21E056LALITHKUMARU]

I am actually trying to read the Regen data from VOTOL EM 100 via the RX TX pin , Do you have any suggestions

[@jerichogeronimo1974]

How do you extract and save a copy of a firmware? I want to save a copy of the firmware m em50s uses

[@aarongallani9799]

Hello there new to all of this, i have a em70 controller , bin files where would i find them?

[@TackleThat]

They are in the description.. did you try them? Not sure if I should test this on the em100.

[@scooterup5903]

hi can any one help me?? i need some file of your settings im using votol em150 and mid drive motor 4000 watts when i push the throttle its clicking only motor wont spin

[@marcelocmj6680]

Hi something similar is happening to my EM50SP it always bring 0 at overvoltage and phase current..... write is ok but comes with 0.... i think is bricked...., do you think that can be fixed with a similar procedure with proper em50 firmware? will debug mode exist for em50 software too? thanks in advance

[@VOTOL_MAGIC]

Yes. It's possible way to rewrite settings but in another way.

[@luiscabrera8749]

@@VOTOL_MAGIC i need help with a votol em30sp do you have the files for this one?

[@fzmetric]

by the way, do you have link of votol software that you use?

[@VOTOL_MAGIC]

disk.yandex.ru/d/p7vsRKkgWqXiyg

[@fzmetric]

@@VOTOL_MAGIC thanks you very much..

[@SergeyKashuba]

Hello! you have firmware on EM150SP. Can you send it?

[@goshka2386]

Здравствуйте, есть ли у вас прошивка на em200/2?

[@VOTOL_MAGIC]

В комментарии ссылка она совместима.

[@goshka2386]

Он прошивается, но всё остаётся в настройках как и было, и ограничения оборотов до 2200 об/м

[@VOTOL_MAGIC]

По моей инструкции следовали?@@goshka2386

[@meetpatel9075]

Do you have latest bin file for CAN based EM100

[@VOTOL_MAGIC]

Try one of available in description firmware. You should luck. All action you will for your OWN RISK. :) In description firmware compatible (tested) with 150/2 200/2 260/2 try with 100/2

[@TackleThat]

Did it work on the EM100?

[@fzmetric]

This firmware could use in em150 can bus?

[@VOTOL_MAGIC]

/2 you can.

[@fzmetric]

@@VOTOL_MAGIC my friends uploaded into em100 and then em100 can't communicate again to laptop, If bin file upload to em150 same thing happen such em100?

[@VOTOL_MAGIC]

@@fzmetric because EM100 doesn't support CAN Bus, i will try to help your. I'm uploading now few firmwares for your. Wait .

[@VOTOL_MAGIC]

​@@fzmetric Try any firmwares from this and your controller will up: --- disk.yandex.ru/d/lcV6N30ttnocbw disk.yandex.ru/d/TC5kSb2wRJjVTQ disk.yandex.ru/d/sA9qu_usFZGc6A disk.yandex.ru/d/a4ws0R2I783XZA Instructions for upload: Just open port of controller and upload firmware WITHOUT CONNECT --- Give me your feedback.

[@fzmetric]

@@VOTOL_MAGIC em100 my friends is can bus..

[@gerardopereyra3989]

Hola saludos de Uruguay compre una VOTOL ME30S para practicar la programación no me funciona el motor y tengo un código 00000280 no entiendo el manual de códigos

[@fzmetric]

Do you have firmware em150 can bus? Please..

[@VOTOL_MAGIC]

CAN BUS is 150/2 ? or... ?

[@fzmetric]

@@VOTOL_MAGIC how i can identify series em150?

[@VOTOL_MAGIC]

@@fzmetric factory USB dongle has 2 contact or 3 ?

[@yasmanyalmaguerquintana8206]

necesito un firmware para mi votol EM 100S ver 1.5 microprocesador stm 32 necesito actualizar a la sw 2.33

[@bodnypa]

tks you so much

[@bikesareco3749]

absoulute ledgend