VW Golf 5 how to adjustment camshaft angle / VW PD engines adjust camshaft emissions problem

[@plokijij7856]

Second video I’ve watched of you working on the timing and the second time you’ve made a mess of it! 😂 these video are good for showing people what not to do!

[@weeniewawa]

I am glad I am not the only one with cut hands and arms from the hose clamps. thanks for your video.

[@matthewbaxter7502]

You are spot on golfwagen my Audi A3 1.9tdipd BLS engine runs perfect on torsion value - 2.5 KW starts & runs well great mpg 😊👍👍👍👍

[@frankyghost7256]

WHY - 2,5 , and not zero ?? zero is perfect synchronicity

[@binagarten4667]

@@frankyghost7256 0.0 is where I set it and where the Stealership sets it. I have never had any issue (touch wood) with this value in the 12 year I have had the car.2 timing belts changes done.

[@frankyghost7256]

@@binagarten4667 ok, i set 0, too, so do i

[@bobirving6052]

@binagarten4667 Thanks for sharing your experience with good running and good mpg when torsion is set to -2.5 KW. Why mileage do you get with this setting compared to the dealership setting?

[@matthewbaxter7502]

@@bobirving6052 Hi I've been getting anywhere between 55 - 65 mpg 👍.

[@chrisbearden1331]

Thank you very much for making this video and showing how to set this. I also need to do this on my vw. It's great to see someone actually making the small adjustments and the results, so I'll know how much to move mine too.

[@jemmace2586]

haha thanks for posting this video! I'm going to attempt changing my cam belt when it's due, think in about 40,000 miles time.. when I do I'll come back and watch this video again! very honest of you and informative too.

[@seb7367]

La température moteur doit être a 90 Degrés Celsius pour avoir un réglage correct a cause de la dilation des pièces mécaniques !

[@radubond]

Mulțumesc pentru aceste informații

[@Blandy929]

Im not sure I understand why people even do this. If you follow a timing belt video the belt tensioner is what sets the angle while the cam and crank are locked with the timing pins. My belief is you can essentially check the stretch of the cambelt by the angle as they usually mark the angle on the cambelt cover. Mine went from -0.5 to 3.3. I followed the skf video to replace it and it ended up at -0.5. Runs great.

[@Juppie902]

I think it helps fine tuning the PD cam lobes, i did my TB and now hard starts, smokes on idle, sounds like a T72 tank, i didnt check torsion yet but its my next step. With old belt it started having hard starts only lately, but ran ok i guess. was overdue by 13k km. SDi engine code BDK 2.0L Also must mention I did the timing check 3 times, each time i was scared i messed up and aligned crank and cam to TDC and restretched. Checking torsion is importznt after TB IMO.

[@bobirving6052]

@Blandy929 These BRM engines specify -3Kw to +3Kw.

[@CologneRob]

Where can i get the right value for my asz tdi VW 130ps engine?

[@abdulbeany1894]

What are symptoms if torsion value is wrong

[@nightking4110]

I have Golf 5 1.9 tdi BLS Motor….and i have -4,4KW…….the engine starts normally and everything ist ok….. should I leave it like this or try to adjust something?

[@fixandrepair6666]

Tak jsem se mrkl. A mám tam 2,5 a při zatížení 2,9. Když jsem dělal rozvody tak jsem nic nedolaďoval jen jsem to zajistil přípravkama a vyměnil rozvoďák.

[@golfwagen4173]

Musím odpoveď poriadne sformulovať, zajtra pozajtra odpíšem podrobne

[@MrZimmaframe]

I have 2007 golf 2.0tdi and can't afford VCDS so I guess I just use locking pins then turn engine by hand and if everything is ok I won't adjust because i won't know exact torsion number without VCDS. So it will be ok and only off by a little bit yes?

[@earlygamer9106]

Aliexpress bro

[@MrZimmaframe]

@@earlygamer9106 lol i had a look there was so many for sale i didn't really know which one to go for m8.

[@bobirving6052]

I want to know this also. Another video said you still need to fine tune it.

[@alinalexandruzomant6347]

Is this same for 2.0 tdi? Thank you

[@Ivan-dx3wr]

Hello! I have a problem with the phase of my golf 5 1.9 tdi BLS. What is the optimal value of the torsion value? Should it be measured hot or cold? Is the value of my golf 0.0? it's not good? I hope you will answer me! thank you!

[@ambermak1296]

-1.5 - 2 good bls.. My passat 1.9 tdi

[@faresfarok503]

I think that the best value is o.o

[@hassancars5471]

0,00 is goood 👍🏻

[@hassancars5471]

@@ambermak1296 it must be set to (0,00) to avoid injection problems

[@ovi_4]

The tolerance is + or - 6 but the absolute ideal value should be as close as possible to 0.0 when the engine temperature is at 90 degrees Celsius. Why this guy wants it at -2.5 is beyond me.

[@Lee-eu6wf]

What vcds do I need 🤔? So I can adjust the value of my bxe

[@szprn2006]

Finaly, Is there any solution ?

[@grasutzum2010]

Greeting my friend , you should research a little bit more before posting such thing on youtube. Torsion value should only be modified only when the engine/water temp. is at 90 degrees mark. Otherwise the timing belt will worn before the 60k km mark. Take it as constructive criticism, i like your channel and i'm a fan ;)

[@Rinxtzu]

Nice advice Madalin! Do you work as a mechanic? If so, where?(i really need a good one 😃)

[@SalisOK]

What are you talking about? Your post does not make sense. You talking about adjusting torsion value when engine is warm and then you say that timing belt will worn oht faster if you dont do it? Wth?

[@Perokoulos]

What is the correct value? How do you calculate it?

[@danielmann4263]

Listed on tb cover

[@jamesnickless4909]

So when you got 0.0 as the torsion value how did you know whether to advance or return and by how much did you turn the central bolt before you got a reading on the screen? I have 0.0 too but do not know how much to turn it in order to start getting a readout. It seems you missed those out between each start of the engine which is what i really would have loved to see. I really want to know how much you turned it to get a figure display again

[@Azrael1x2]

You should keep it at zero

[@hamham4547]

Where you can find the right value

[@krunoslavnegulic9939]

VCDS, measure block / 004. If it is -, it is retaded, + is advanced. Best performance from +0,5 to 0,0. If you work as this guy, turning cam and not sprocket, clockwise is advancing timing, anticlockwise is retarding (1.4 tdi 59kw)

[@diagnonamir4037]

hhh finally it makes you spansh. thanks for the efforts.

[@agentulcupar]

I have the same motor, was imposibile to set corect value first was -3.4 neaw -4.4. I was tryng 15 times and no succes.

[@andreoliveira-ye9mq]

How much did u payed for the software um looking for my Audi A3 thanks

[@radioauto4423]

hello please if possible to remove component protection seat /vw/ audi ..... by vcds

[@golfwagen4173]

without knowing the pin you will not change. you will only change the parts that pin does not need eg. door module

[@danielbob7769]

how can I find the right torsion value for my engine?

[@axelmckenna3659]

If this value was to far out would it cause cranking but no start??

[@Freakzter88]

Yes, none or very hard starts are usually the result because the timing is too far off.

[@MrEni112]

Hi which is correct value on 2.0 tdi bmp engine actually is -2.9 ?

[@razvanungur16071987]

Correct is between -1.5 and 2.5

[@binagarten4667]

Strange ECO VCDS man says the best is 0.0-0.5 Torsion Value. Mine I adjusted and 0.0 is the best.

[@bobirving6052]

Best for starts? Power? Mpg?

[@aniquerizwan]

Cant you just a timming tool for this? Those that hold the teeth of cam pulley and crank puloey as well to make it where everything needs to be...rather than hit n trial like this?

[@youna1562]

0.0 GOOD

[@hassancars5471]

Yesss

[@bobirving6052]

@hassancars5471 Why 0.0Kw good? Best for power? Best for fuel economy?

[@crincrin8411]

Why the mileage on the fault is 311501? You mileage car is low

[@patrikjamajka1692]

Cauko, preco na -2.5 ? Vacsinov sa dava stale na 0.0/-0.6.

[@faresfarok503]

Are you serius 0.0 is the best value

[@azislo]

No. 0.0 can mean completely wrong. This value should change a bit with RPM. If it stays on 0.0 then it is out of sync!

[@MrZimmaframe]

13:44 "back" 😂

[@julyjuly7711]

Ahoj nepochopil sem videl vsak si mel synchro na 0 to je ok... nebo proc si to resil

[@golfwagen4173]

Pre tento motor je -2.5

[@julyjuly7711]

@@golfwagen4173 a safra ja myslel ze 0 prave ze... zeptam se asi nemas.v merku jake hodnoty u motoru 1.9tdi AVF... nejak mi to moc zere mi prijde. Hybl sem do plusu ale na volnobeh takovy neklidny

[@ahmedboumaalif5250]

good

[@davidpiroska7058]

Po vymeneny tepelneho senzoru chladiacej kvapalany este stale tazke starty a trasenie motora, po chladnom starte 0,5 l na volnobehu po zahriati motora na 90stupnov 0,7 L a mensie trasenie motora. Spojka dvouhmota 80tis km som najazdil, vsetky silemtbloky menene. Napad co by to mohlo byt ?

[@davidpiroska7058]

Motor 1.9 tdi 77 kw bkc 2005/04, teply start upraveny pocitac ok

[@pauladams9477]

Engine must be at normal operating temp for this procedure!

[@BigBadjohn0x0]

How exactly do you do that if it only runs a max of 2 mins....do tell!!!!!

[@kreshnikmorinaa]

What is the correct values

[@golfwagen4173]

I think every engine has it differently. for my bls it's right -2.5 -3

[@bobirving6052]

@golfwagen4173 Has this value -3Kw to -2.5kw been good for power and economy, or have you adjusted it differently now?

[@hassancars5471]

you're not normal you have to put it on (0,00)😂🤷🏻‍♂️

[@WearenerdsShop]

But green light on the tacho is DRL?

[@golfwagen4173]

Yes, DRL

[@WearenerdsShop]

@@golfwagen4173 you have tutorial to make?

[@shaiknaveedalam7208]

Hi friends I face pd injector problem the code is P1266 P1260 P1263 Wat is problem please help Skoda Fabia 2008 1.4 tdi

[@darrenturner9406]

I have golf mk5 2.0 tdi 170 dpf .engine code-BXE...I believe its a 16 Valve Twin cam engine. Can VCDS measure torsion values for each cam and if so do you know the torsion values?

[@Blaaggarding]

Bxe engine is a 1.9 8 valve pd engine if I remember correctly.

[@danielking4067]

What Engine Code is this BXE or BKC?

[@golfwagen4173]

BLS

[@dumy5035]

@@golfwagen4173 hello for the 1.9 bls engine which is the best calorie??

[@АлексейЗ]

Poland

[@fixandrepair6666]

Ahoj, je tam přece tolerance +-6 tak nebyl problém na emisích někde jinde? Schválně to změřím u svého auta. Byl jsem nedávno na technické a oba mechanici koukali že mám emise jak s novým filtrem částic. Možná to je tím že jezdím denně 160 km. A to mám nalítáno 350 000.

[@golfwagen4173]

no. moj BLS ma mat -2.5 až -3. lenže to som nenašiel v žiadnom návode lebo nemám prístup k návodu. nikdy som nemal problem na emisnej, až ked som to mal nastavené na +2. dalsim problem pri nastavení na +2 bolo že, ak som mal motor zahriaty na vysokú teplotu napr. po dlhšej jazde do kopca, na kopci som vypol motor a po 5 min prestávky sa objavil problém z teplyím štartom. po 20 minutach už štartoval normálne. auto pri nastaveni na +2 smrdelo (ale chapem že to môže bit len moj pocit). po nastavení na -2,5 už nesmrdelo ale, hlavne zmizol problem z teplyim štartom. su auta čo maju bit nastavene na 0 a možno su auto co maju bit nastavene aj na inu hodnotu. ja som to mal vlastne nastavené o 5.5 až 6 stupnov špatne a takto sa to prejavilo. a ta hodnota +-6 podla mna znamená že, do tejto hodnoty ti to ukáže ale ak si mimo tak ti ukáže 0. to je ale iba moj postreh a pocit.

[@golfwagen4173]

teda 4.5 až 5. +2--2.5 až -3

[@fixandrepair6666]

No já co jsem si stahoval z erwinu originál servisní manuál tak tam o tomhle nic nepíšou. Jediný co tak že se to má zaaretovat přípravkama a to je vše. Ale koukal jsem na hodně videí kde se to lidi snaží nastavit na nulu. To by mi i dávalo smysl že nula je ten střed. Ale nevim.

[@golfwagen4173]

pred výmenou som to mal na -2.5. po vymene 0.0. potom som zhodil remen ešte raz, nahodil naspet a bolo tam +2. tím chcem povedat dve veci a to že pred výmenou bolo -2.5 originál a druha vec ze tam staci tak malý pohyb (stačí na to škaredo pozret) a už sa to posune

[@fixandrepair6666]

golf Wagen 😂😂👍

[@mohamedhedi3740]

My torsion value is 7.8 it's bad or good for engine bxe 1.9 tdi golf 5

[@faresfarok503]

Very bed

[@mohamedhedi3740]

@@faresfarok503 why

[@faresfarok503]

+ 7.8 الماكس + 6 الافضل هو 0.0 هنا عندك لافونس و منها تزيد استهلاك المازوت

[@mohamedhedi3740]

هي كانت 0.5 و لكن كيف غيرتها لل 7.8 اصبح تفاعل المحرك افضل

[@faresfarok503]

@@mohamedhedi3740 قصدك التيراج زاد ؟

[@ianmilo9982]

I give English classes.

[@GiveMeYourNose.]

Give

[@superfill75]

guarda che sei senza liquido radiatore.......

[@greggsmith5391]

The engine needs to be hot when setting this

[@BigBadjohn0x0]

HOW DO YOU EXACTLY DO THIS if it doesnt run for long enough to get up to "temp"

[@bobirving6052]

You can get it close enough to run right when the engine is cold, then fine tune when it’s hot.

[@nemanjadzombic6101]

Total waste of time!

[@GiveMeYourNose.]

Why