Waste oil distillate fuel - ethoxide cleaning, odor removing.

[@marciofernandobarci]

very good recipe to make biodiesel. I'll dare suggest you can add to process - using quicklime instead silica gel to dehydrate final stage. In Brazil - before our national alcohol project (for fuel) when high technology were developed, the production of dehydrate Ethylic alcohol was done by quicklime. I believe 100 or 150 g of lime might be enough - try it. Congrats to you

[@daneitor97]

What is the best way to dehydrate ethanol/ethylic alcohol? I want to run my car on pure ethanol but I can only but 95% ethanol

[@marciofernandobarci]

@@daneitor97 Look - I'm not specialist in distillation of alcohol, despite some experience in it. All processes involving dehydration of alcohol are not simple and cheap, mainly for small volumes. I suggest you might try using quicklime - it might absorb rest of hidration of alcohol - totally or partially... you must try to confirm

[@stefanlowet2189]

its not biodiesel , waste engine oil is used

[@maciejc.617]

Hi there :) 1. I hope the tank and pipes you are using are not made of aluminum but stainless steel, because aluminum and its alloys will corrode in contact with NaOH. 2) NaOH is a strong base, "rinse" the oil with one liter of water will not remove it, it should be neutralized with some acid imho. 3) I think silica gel absorb water, but with NaOH, so it should not be dried and reused. 4) Dissolving NaOH releases a lot of heat, which may cause the solution to boil and splashing it around. In general that is interesting video. 👍🏻

[@santeryi9]

The tank is stainless steel, the NaOH is in miniscular amount reacted with alcohol releasing the heat, so added to the fuel cold with no exothermic reaction, then it reacts with tar, settles and drained, washed and drained again, copper stripe test or water extract test is done upon the use, the used silica is mixed with NaOH again and boiled with a bit of water that turns it to sodium silicate, then dirt collected from the top of solution, later sodium silicate is converted to silica gel again. Also note that if any NaOH would be in the treated fuel, then silica gel will react with it and become neutral sodium silicate, so there is no alkali in the fuel.

[@valuablegem5307]

What's this tank and what's the process

[@hayden6930]

This is great, just discovered your channel. I run only diesel vehicles and collect enough waste oil to power my vehicles even with an 80% recovery rate through distillation. I've been wanting to have a go at cracking it for the longest time. It seems like the addition of a centrifuge could be quite useful at a variety of stages in the cracking and refining processes?

[@santeryi9]

Yes the centrifuge at the final stage would be a great addition.

[@hayden6930]

@@santeryi9 have you considered using waste gas or light fractions as the heat source for the still? I imagine that would come with risks, but the reduction of electricity demand seems possibly worthwhile?

[@hayden6930]

@@FirstLast-tx3yj I personally have no use for petrol/gasoline, so that wouldn't rank highly in my priorities. I use a bit of diesel though. I'm yet to attempt any of this. One of these days ill get there.

[@bacemkbiri8877]

Do you process it before putting it in the car's tank

[@incandescentwithrage]

Just run filtered waste oil in an iDI. The only step.

[@FFsCMs]

You should be able to improve your drying result, if you neutralize the remaining NaOH (for example with some muriatic acid) in your solution before adding the silica, as silica does not work well in basic environments.

[@步川庫紫]

CaO better

[@kelvinsparks4651]

A very good and clear / easy to understand video, well done . Just wondering how the costs weigh up compared to diesel from the pump.

[@tonydiesel3444]

Maybe .25 cent a gal

[@tonydiesel3444]

Or less

[@juncusbufonius]

Expensive, 4-5 days, need a container big enough & stirring device. The outlay for those is high enough but in Europe those chemicals have to be bought in large enough quantities to make it cheap (1Kg NaOH == £4, Alcohol 1L £5). My time alone would make it cheaper to fill up at a gas station. And you still have to dispose of the waste materials which you need to drive to the disposal site in a vehicle. So if you do happen to have the gear lying around and you don't have anything better to do with your time then you get what? 3-4 gallons from 5 gallons of oil. That would take me a few years to get from oil changes anyway.

[@tonydiesel3444]

@@juncusbufonius recovery rate is probably ninety-plus percent fuel here is 490 a gallon so I can make 100 gallons at $0.20 a gallon you do the math machine can run at the house when I'm off of work or on days off or through the night every night of the week and maybe produced 15 gallons per run or 20 over time you will save a fortune

[@ubaidkhan3294]

@@tonydiesel3444 bro which additive use this in engine oil can u please tell me

[@vacuumsetting]

Oxygen can not be used while stirring. It is a strong oxidizing agent that significantly affects the process itself and its result. For chemical mixing, it is necessary to use a rotary mechanism with a frequency converter...

[@santeryi9]

Yes I know, this is a poor man's system, planning a recirculating centrifugal pump for mixing.

[@vacuumsetting]

@@santeryi9 The fuel cleaning process, i.e. sorption of the product cannot take place in this way, it is not serious. You could take a simple funnel

[@aymansaied780]

Do you mean that the material should be thrown. and stirring. And this must be isolated from the air. Or the barrel is closed and suspended from the top by a motor with an internal stirrer

[@warrenm374]

What about a mixture of 78% nitrogen and 20.9% oxygen?

[@dexterstudio480]

@@warrenm374 thats air and what alek is using and has been advised not to

[@PotatoesAssistant]

This whole process seems similar to how biodiese is made from waste cookin oil except normally methanol is used instead of ethanol, and it’s heated before being added to the waste oil

[@ljprmc]

Has the waste oil distillate shown in the video been produced with the home made still as in earlier videos ? Or is this process a direct treatment of WMO into a clean WMO for blending into a diesel fuel alternative ?

[@hydrocrow1108]

Since its referred to as distillate.....

[@vasilepopescu5742]

Many thanks for sharing this tehnic with people... I m hapy to find your video! ✌️My ask is: how old car I must have to runing on this fuel!??? Many greetings ✌️

[@santeryi9]

Best for plunger type fuel pump equipped cars.

[@ianminedesfiles]

may I know what results you should get with the hydrometer? Is it required?And also do you know any alternative heating equipment aside from cartridge heater. Is it possible to use stove to hear it?. You are very skilled!👍🏻👍🏻

[@santeryi9]

Hi the hydrometer should show 830 to 845kg per cubic meter, it is a standard requirements, so all the passages and filters are able to establish a proper fuel flow to injectors, the heating can be done with a heated water jacket made around the cylindr, then you can use aa simple water heating element, though make sure that the system is opened to atmosphere, to avoid any steam overpressure.

[@GuiFalked]

I'm going to have to think this might make a nice way to clean up some types of homebrewed biocrude as well 🤔

[@alhajjmuftimuhibbullahmiazi]

Thank you so much from my heart. Go ahead for mankind. No doubt YOU are a good scientist.

[@santeryi9]

Thanks a lot.

[@daudhamdard]

Haji sha formula da wala

[@SyrianBiodiesel]

Hi, I would like to tell you what I do when drying biodiesel. After raising the temperature, I turn on the air for 15 minutes and all the moisture will evaporate quickly.

[@santeryi9]

Good, I am not running air after the heating, as there is some silica gel and other deposits at the bottom, just do not want them to float around.

[@مظاهرامیرلطیفی]

اسیدبزن

[@theaussienurseflipper.8113]

G'day mate, does the silica gel just stay in the tank? And you drain good fuel out thru it, cheers

[@RabbitInAHumanWoild]

Dissolving NaOH in EtOH does not make ethoxide. You have merely created a solution of NaOH in alcohol. Ethoxide is a much stronger base than hydroxide.

[@axer451]

You can make ethoxide by adding naoh to ethanol,

[@ppphhhh131]

Is this reclaimed base oil and how to clean more and make it bright yellow golden

[@santeryi9]

In my case I use it as fuel, so no real need to make it bright yellow, bur I would recomment to store it with silica for longer period of time and it will become bright yellow in week time, so some absorbent will do the trick.

[@cmte.brazinazzo2061]

I tried, Polyether Amines TEPA, and it also cleans the fuel. It sequesters the dirt. Getting a thick black goo to the bottom of the container. But it take 2 weeks to do it.

[@santeryi9]

with this method the black goo drops in 30min.

[@urgentcareguy3]

Nice job Alek! I have your plans for a WMO distillation set up. Diesel obviously has a particular odor to it when burnt. WMO when burned, has a less tolerable smell. Does the process in this video change the odor or smell to more like traditional pump purchased Diesel?

[@santeryi9]

Yes, removes the odor from the homemade fuel, makes it less prominent than the pump diesel, smells more like a fresh engine oil.

[@stevengarcia8469]

@@santeryi9 please I’d like to know how much it’ll cost me to make a set up which will purifier about 500-1000ltrs in a day.

[@randybrown9706]

Can the dirty residue be used as heat source

[@fatimaomoloriomolori5337]

Mamy thanks to you for sharing your knowledge. Pls how do i recycle waste lubricants oil into useful oil.. i need your advice plss

[@vijaygavarasani9137]

I'll tell you

[@usmanmajeed4256]

@@vijaygavarasani9137 please advise

[@grapsorz]

what do the silica gel do? other then pull some water out? do it pull other stuff out?

[@santeryi9]

Removes tar, polymers, colorings, the silica gets dark, the fuel gets transparent.

[@grapsorz]

@@santeryi9 is it possible to get that out of the gel again? like burning it out.

[@santeryi9]

@@grapsorz yes you can burn it out

[@theaussienurseflipper.8113]

Did U remove the silica beads? Cheers

[@szucslorant4115]

Hello. congratulations on a perfect and scientific video. Thanks. I would like to ask what materials can be used instead of ethanol? can it be replaced with gasoline? What should I do with the remaining excess solution that settles out? How can it be used in an environmentally friendly way?

[@MedoKojiZiviOvde]

Usually people use methanol which is far cheaper.

[@marinvremes5702]

Or kerosene, but be very careful, it's highly flammable, you don't want to harm yourself.

[@szucslorant4115]

@@marinvremes5702 Yes , Be carefoul. Thanks. here not cheapest the ethanol, its realy heavy to buy here.. or is double price .so... i need found a way to replace.

[@samir-chaway01]

did this operation, but unfortunately I did not succeed, despite my admiration for the idea. Can you explain it to me in detail?

[@santeryi9]

First of all, the oil was distilled, then processed cold. Please note that this oil is not directly from a sump. The oil was distilled first.

[@samir-chaway01]

@@santeryi9 please help me 🙏 for this proced

[@sunilperera5553]

Thanks a great video, which not only save money, but soil pollution by WMO. I have a question. Waste oil may be containing a part of synthetic and semi synthetic oil also in it, say 30%. Would this method still valid and give a good fuel or do we need to alter the volume of silica gel/ethoxide to remove impurities?

[@abbasvaliya4646]

.

[@nwzz]

Hello, thank you so much for this video, is it possible to get more details, qty , concentration of alcohol etc ? Regards,

[@saadjaved4274]

Hi, is there any chemical which can be used to adjust the ph of waste engine oil before distillation to avoid thermal cracking?

[@davenlackey9763]

Ethanol amine

[@tek4]

Acids and bases

[@mickwolf1077]

You got yourself a sub, i gotta try this. Been collecting wmo but to use in a conara im going to modify but if i can put it in my landcruiser that'd be great.

[@santeryi9]

Please note, this is WMO distillate, not a straight WMO.

[@ZarawarKhan-gs8hr]

​@@santeryi9 means u first distilled a wmo into distilled wmo right?

[@santeryi9]

@@ZarawarKhan-gs8hr Yes you are right, it is distilled oil.

[@danbrown935]

That’s great if you’re retired. A lot of work to get setup. Great video thanks

[@loricoenvirotech2032]

Thanks a lot for this video sir. What should I do to recover silica gel again after use so that I can re-use it for the next process?

[@santeryi9]

Bring it to red hot state with some sort of furnace, burn all the absorbed hydrocarbons out, then cool down and store in hermetic container, you may use it a couple more times. also you can dissolve it in potassium hydroxide, filter, and solidify back into the silica gel form by reacting with sulfuric acid, washing, drying and temperature activating.

[@loricoenvirotech2032]

Thank you so much sir. Can I ask how you blend the finished recycled engine oil to be used as fuel for plunger-type diesel engines? What kind of low hydrocarbon fuel is best to mix with the recycled engine oil? Can I blend it with gasoline? Like,20%gasoline and 80% recycled waste motor oil then check the viscosity if its like normal diesel fuel viscosity. What can you suggest? I want to use it for my Year 2000 model isuzu diesel wagon plunger tyoe injection pump and for my diesel engine farm machineries. Thank you.

[@zikragreenfarm]

Thank you so much dear sir...i want to do this as a small business...so sir can this oil used in vehicle as commercial diesel fuel....or any bad effect in vehicle engine if its run vehicle regular basis please reply I'm very hopeful from u sir

[@santeryi9]

If resulting fuel is treated properly it can be used in any diesel vehicle, one of my cars is driven predominantly with this type of fuel for the last 11 years and it has 440000km still going strong, here is another way of fuel treatment: the first step: kzbin.info/www/bejne/pnS0c2p4qpmfqLssi=xpZVUTH9SPC-0U_G The second step: kzbin.info/www/bejne/o2S6iqR5eLaNbac

[@christopherleubner6633]

Sodium ethoxide can be prepared in two ways. By reaction of sodium metal in ethanol, or by electrolysis of an anhydrous solution of NaOH in ethanol at high current.

[@dubstepTonme]

Respect to Avidyne/Aspen for stepping up with a glass panel. This is going to be brilliant.

[@lakshanpasindu6000]

Hi thank you so much for doing this amazing video. Good job, but can i use methanol instead of ethyl alcohol and what is the purpose of adding silica gel?

[@santeryi9]

Hi, I think you can use methanol, in my case I am trying to avoid toxic reagents, the silica is absorbs water, tar and polymers, greatly improving the final result.

[@lakshanpasindu6000]

How long should i mix sodium hydroxide with methanol?

[@jamesboline6280]

@@lakshanpasindu6000 I think you have to use potassium hydroxide with methanol (Methoxide)

[@kuripotech461]

How much did it cost you to do the whole process and versus how long will you be able to use that for whatever purpose you want to?

[@rrtsduf]

Yea... plus time

[@Null-o7j]

Diesel is good if you need over 300hp, but anything less I think gas is superior. Eagerly awaiting followup video of you cracking the diesel into gasoline.

[@santeryi9]

Totally agree,though I prefer either 1000hp locomotive diesels, or simple underpowered 80hp single bum movers, so any diesel is good, specially in off road conditions.

[@felixOkitikpi]

I have received your email may God continue to show you love as you show me this ingredients to produce

[@santeryi9]

Thanks a lot for your interest and comment, please note that here I am treating the distilled oil, not the straight one.

[@johnlong384]

Pretty nice and yes, you could have made Schnaps with the same efforts too.

[@santeryi9]

sure, check my channel, there are plenty of Schnaps videos too.

[@johnlong384]

10-4!

[@freedom_aint_free]

You probably is getting something other than ethoxide: CH3CH2- as sodium hydroxide in spite of being a strong base is not strong enough to generate ethoxide the reason being that the ethanol is a extremely weak acid, and in order for it to react like one you need brutal bases: metallic sodium (particularly in aprotic solvents like THF) is a good one, I guess you could use Lithium from batteries too. diluted acidic potassium permanganate (say in diluted sulfuric acid) can be also used to oxidize some impurities and you can clarify the colloidal suspension of MnO2 with sodium sulfite afterwards..

[@KashifAli-mm5ox]

pyary bhai yr btaa den gye ap kitny litr me kitna graam chemical dalna chahyie ..10 litr ho to

[@mihamaker]

Thank you for this video, this is a real treasure. Collecting WMO for some time, using all kinds of wmo burners but needed better and cleaner application. Also using cooking oils only filtered and 50% diesel mix directly in a car. No problem at all. One question, the black waste product, tar-looking, can it be used on concrete and wood for hydro-isolation or maybe distilled further into a more thick mass?

[@samirhuskic2404]

Pozz Mihovile Za koji tacno automobil koristis mjesavinu dizela i ulja? I ja sam poceo istrazivati o tome pa sakupljam info Hvala

[@mihamaker]

@@samirhuskic2404 Pozdrav, koristio sam na Renault Kangoo 2000g i Espace 2007g. Na Kangoo bez problema 75% mjesavina ali ne u sred zime. Teže pali. Kad se zagrije onda može, ali treba tada drugi spremnik koji bi bio u putnom prostoru po mogućnosti grijan indirektno sa toplim zrakom ili uronjena spirala spojena na sistem hladjenja motora. A trenutno s prekidima na Fiat Scudo 2013. Nemam vise toliko dostupnog rabljenog jestivog ulja.

[@samirhuskic2404]

@@mihamaker Hvala ti puno na informacijama,ja imam passat 5 plus i te njihove pumpe navodno ne trpe ulje,trazim neko starije auto da eksperimentisem

[@mihamaker]

@@samirhuskic2404 Čisto sumnjam. Problem je sa rijetkim mješavinama tipa lož ulje kerozin i slično. U tom slučaju na puni rezervoar bi trebalo ubaciti minimum litru dvotaktola i to je to.

[@alexdissieux5137]

​@@mihamakerbonjour 😍... vous rajouter du carburant (mélange essence-huile) ou de l'huile 2temps?

[@tomayrscotland6890]

would it not be better just to buy red diesel if locally sourced.

[@MrMraza123]

Excellent video.

[@marchawthorne2479]

What would this fuel be used for? Thanks, I have the opportunity to get lots of waste diesel motor oil and auto oil, and used cooking oil, can I mix them together or would they need to be processed separately? Thanks for the great video

[@santeryi9]

The cooking oil should be processed separately, and the final result can be mixed. Waste motor oil should be distilled first. The fuel is for my diesel Mazda MPV 2500cc turbo diesel.

[@ghost2coast296]

Chinese street food

[@mdaslam3561]

Sir cleaning one's engine oil with silica gel is a bit costly sir do you have any process which can renew the engine oil at low cost would be very helpful sir

[@captainotto]

It's only costly if you cannot reuse the silica after the process. I wonder if it can be cleaned after its used. Maybe a solvent wash then a drying would make it work again.

[@kreasiumum]

It's a very long process, approximately what percentage of clean oil do you produce?

[@santeryi9]

Yes it is a long process, take into account that I show how to do it in a bigger volume not in a lab glass. the process can be replicated with a much bigger quantity and it will justify time spent.

[@coachgeo]

would it be beneficial to do this with raw wmo to get as much yucks out of it (aka..... less to filter/centrifuge cause it fell out via this process) prior to distilling to a diesel fraction?

[@johndowe7003]

You could but from what I gather is that a lot of mess forms at the bottom and lowers efficiency and makes things more dangerous

[@coachgeo]

@@johndowe7003 that is my point.... only centrifuge what is above the settlement. will then take less centrifuge passes to get an oil that is more uniform... thus will crack easier and cleaner as you distill it.

[@richardrussell7740]

HI THANK YOU VERY MUCH FOR THIS FANTASTIC VIDEO.I OWN A WORKSHOP SO HAVE ALOT OF OLD ENGINE OIL.I DID EVERYTHING AS YOU EXPLAINED BUT MY OIL IS STILL BLACK.CAN I INCREASE THE VOLUME OF THE CEMICALS TO SEE IF I CAN CHANGE IT TO A LIGHTER COLOUR OR WHAT DO YOU SUGGEST I DO.THANK YOU FOR ALL YOUR HELP.

[@santeryi9]

Hi, please read the description - I am treating the distilled oil, not the black one from a sump. Hopefully, soon I will upload the oil cleaning method video.

[@siperhallo]

@@santeryi9 koniecznie

[@nwzz]

@@santeryi9 Hello Alek thank you so much for your sharing, what's the hygrometer value after 3 days?

[@mohammadbashar386]

Is this method suitable for recycling motor oils?

[@santeryi9]

no.

[@mohammadbashar386]

@@santeryi9 I need a way to recycle motor oil

[@dinosshed]

It'd be good on a much larger scale. I don't have two weeks spare to make 20 litres.

[@santeryi9]

not two weeks, you can do it in two days, and yes you can do it on a bigger scale easy.

[@theaussienurseflipper.8113]

Easy mate bigger drums

[@1admission]

Can diesel engine run on oily hand sanitizer? Such as hands sanitizer with aloe vera oil.

[@santeryi9]

No.

[@krzysztofgrzyb6095]

Fajny filmik tylko szkoda ze nie ma tlumaczenia Panie Alek Polek pozdrawiam Kris z Polski

[@johntexan4165]

do you have to use the near 100% Ethyl, or can you use the 70ish% ethyl rubbing alcohol? Huge price difference. Ever tested it?

[@santeryi9]

I use 90+ you can try 70% why not?

[@agrippanyagwaya2308]

After all the process is that diesel suitable for use in any diesel car or truck

[@santeryi9]

yes, after all the treatment it is suitable for any diesel engine.

[@charleskwatche9557]

Please is it possible to make it be used as engine oil.

[@santeryi9]

You need to have a special additives and formulation for your particular type of oil, then you can use it as a base oil.

[@mohamedmustafa6847]

@@santeryi9 can I use it for manufacturing of Lubricant grease?

[@mr_korwagdy1257]

@@santeryi9 so can we use the end result of that oil as a biodiesel or to run a car engine or a motorcycle?

[@santeryi9]

@@mr_korwagdy1257 Hi, yes the resulting fuel can be used as diesel fuel for cars.

[@BuenaVida-km8pu]

porque simplemente no vuelves a destilarlo? gracias

[@DelightfulFishingRod-vw2jc]

It will definitely destroyed engines 😮

[@santeryi9]

have 440000km on the clock already, still going strong with the original engine, while in some countries the pump fuel will kill any engine before it gets to 70000km.

[@danielnashief7463]

If we use more caustic soda or a little more ethanol, would it destroy the process?

[@MedoKojiZiviOvde]

It's better to have excess ethanol as it is a fuel on its own. Excess caustic soda, especially if it is unreacted, will cause saponification and create soap in your fuel.

[@allantulli5546]

What do you do with all that waste you create? Must cost more than the fuel is worth to dispose of it.

[@linctexpilot8337]

It could be burned for heat to distill the next batch

[@richardrussell7740]

HI THANK YOU CAN I USE THIS METHOD TO CLEAN MY BLACK DIESEL ALSO

[@santeryi9]

No, I am planning to show how to clean the waste oil.

[@zikragreenfarm]

Sir can we remove bad smell from pyrolysis oil from same method.... please reply I'm waiting for your valuable support

[@santeryi9]

Yes, this method is specifically used for the odor removal.

[@averagedev7768]

I would be brutally honest, when i did this i bought 2 chepest diesel fuel filters for golf 2, 2 plastic barrels and one pump. then added diesel for it to be 50/50 .I cycled 2 times the used oil thru the filters. The OM611 2.2L Mercedes engine run on it just fine without any issue. I drove at least 40 000km on that sort of fuel. I drove always long distances. The W210 rusted to the point where i cant pass inspection so i just bought a cheap w203 1.8 gasoline with lpg and forgot about the used oil thing. LPG makes me feel i am contirbuting to the cleaner air.

[@saeedkhan07860]

अगरबत्ती में जो व्हाइट आइल इत्र के साथ मिलाया जाता है वो व्हाइट आइल ये ही है या वो व्हाइट आइल अलग होता है।

[@santeryi9]

I would be happy to reply your comment, but for some reason even google translate is not capable to translate it correctly.

[@BensWorkshop]

What do you do with the waste produced?

[@santeryi9]

Still collecting, planning to finish a complete waste processing still, that will reduce it down to solids.

[@BensWorkshop]

@@santeryi9 Many thanks.

[@szucslorant4115]

@@santeryi9 have you any solution ,whats up with waste what produced ?

[@nomadworld6192]

Hi, I am thinking about making my own diesel. Could please help me with some information. Where do you get the alcohol for a decent price in new zealand? Any idea for a cheap set up to produce 30-50 liters per week with an acceptable quality? Thanks!

[@santeryi9]

Hi, I am making my alcohol. Otherwise, you can use blue methylated spirits. It is ethyl alcohol (ethanol) with some die. It is usually 5 dollars per liter in any supermarket. It will be enough to treat up to 80L of fuel sodium hydroxide sold in bunnings, currently trying to complete a construction manual about a reliable system.

[@kieranh2005]

Methylated spirits are alcohol. Also try paint shops.

[@jamesleon2770]

Diesel fan here..located Australia,access to heaps of waste oil at work (mechanic)..have nearly 1000 litres of used oil stashed away Is there any pdfs or such on how to do this?

[@d9_artistchannel152]

how to make used engine oil clean?

[@santeryi9]

First of all make sure that your engine oil is not multigrade or mixed with another oils, then you can use some sort of coagulant, let say sodium silicate, mix, let settle, wash, dry, filter or better centrifuge. But from my experience in modern days the only classic cars intended zinc rich motor oil is easy to recover, the other oil, especially diesel one literally impossible, they designed to keep all the dirt suspended to prevent deposits within engine.

[@guillermoibarra7969]

Awesome Alex!!

[@santeryi9]

Thanks a lot.

[@clebersonsilva2642]

Ei Alek que sensacional seu trabalho tive esses problemas com o combustível lá na África do Sul quando produzi combustível com pneus, plástico, grama já a gasolina de CO2 já saí limpa .

[@got2kittys]

Que ideoma es sus? Espanol, dialect no se O portu, que yo no Saber. Only curios, Englese mi natal idioma. Gracias amigo!

[@clebersonsilva2642]

Eu agora estou no Brasil falo português

[@vedprakashsrivastava2326]

Sirji is machine ka price kitna hai or kaha milega apna address,contact send kare

[@ft.j.gdhjjdhfgjk7248]

كيف نتخلص من اللون الاحمر وهل سخنت الخليط في المراحل الأولى ام فقط في المرحله الاخيره

[@PribadiSahaja]

Nice information. I like your channel. I subscribe. Salam from Indonesia

[@santeryi9]

Thanks a lot. happy you like it.

[@simoamd6335]

Can we used sel instead of sodium or potassium ?

[@ianminedesfiles]

Hi! Does it have to be distilled first by heat and cool it down before I put it on the pot so I can Achieve that color?

[@santeryi9]

Yes it does! The title says "waste oil DISTILLATE."

[@wazza33racer]

so is the WMO just filtered waste engine oil, or has it been distilled by heat?

[@jimjardine4705]

is this suitable to use in a furnace to fire up for hot water boiler to heat house???

[@santeryi9]

Yes, it is suitable for furnace.

[@danielnashief7463]

Instead of using air compressor for mixing the ethoxide inside the waste motor oil, can we assemble an electric motor with a propeller shaft for mixing? 220 volt AC horsepower electric motor.

[@santeryi9]

Yes, will be even better.

[@rayaustria4624]

What did you use for heating the fuel?. Did you produce Disel fuel? Can you use it on vehicles?

[@santeryi9]

During processing, if I need the fiel to be warm I use a cartrige heater incerted in a stainless tube that plugged at one end, I control the temperture by suppressing the element with a voltage regulator, thus I can keep it at any desired temperature, and yes I make my own diesel fuel and use it for my diesel cars.

[@muhammadbaqi5899]

With the addition of several chemicals is thevoul still usabke in the engine?

[@santeryi9]

Those chemicals are just reagents to remove all the tar and polymers from the fuel, then simple water and neutral absorbent. There is no chemical by the end of the process in fuel, and everything is drained and filtered out.

[@mdaslam3561]

You used the silica gel once, can the silica gel tie be used again or is it only used once?

[@santeryi9]

Yes, you can regenerate it by heating to red hot state burning out all the impurities, also may add some sodium hydroxide and turn it into a liquid form of sodium silicate, dilute with water, filter, boil water out add hydrochloric acid and turn it into silica gel again.

[@kishorashish7327]

How can i remove oil from water in waste water and cooling water with Chemicals Treatment..? Can you guide please

[@deniskangethe3718]

Can I use this process on used oil or black oil

[@johndowe7003]

Yes

[@Wasio212]

Hello, is it possible to get rid of carcinogenic compounds and heavy metals that enter the atmosphere during combustion through such cleaning? Have a good day

[@tek4]

Thats what your emissions system attempted to do. It sprays urea mixed with water to the point it won't hold any more, (def), and this not only sequesters the heavy pollutants like metals but cuts down the sulphur dioxide levels too

[@tcmtech7515]

What exactly are you gaining from this process? I've worked with used oil/waste oil for years and all I have ever done is run it through 10-micron filters to get it clean and then blend it with ~20 to 30% E85 to get diesel engines to run normally on it.

[@santeryi9]

Here I am processing pyrolysis oil, removing asphaltenes and tar that otherwise will clog the fuel system. And no need to add any petrol.

[@Paullyell]

price comparison please how much this cost vs how much for new?

[@santeryi9]

Price comparison with what? The homemade fuel with a gas sttion fuel?

[@MaxMaima]

What would be the viscosity then?

[@santeryi9]

About 840 - 830kg/m3

[@pauljohnson2372]

It looks very similar to biodiesel process

[@ryanpoe3054]

Do have a product buying link... where can you buy that stuff

[@impactodelsurenterprise2440]

It seems that silica gel is the most expensive item in the mix

[@santeryi9]

Not really, it is sold as cat toilet, like 10 dollars for 7 liter bag, and needed a small portion, say one dollar worth per 30L of fuel.

[@ZawMinnOo-n7v]

How to clean used engine oil?

[@santeryi9]

Sulfuric acid is one of the most effective means for precipitation, but there are others, I will immediately stipulate that modern complex oils are not susceptible to precipitation, they contain detergent anti-sediment additives that do not allow sediment to fall out in the crankcase, thus many oils and their mixtures (at the service station they are poured into one can) are not susceptible to such manipulations, unless all the oils are collected separately from each other and oil for old-generation gasoline cars with a high zinc content is processed, then it can be precipitated with an aqueous solution of sodium carbonate.

[@ИванПетров-ю6я]

а как со смазывающим свойством у такого топлива? сколько стоит инструкция по сборке мининпз?

[@santeryi9]

Топливо делается из масла, по сути это базовое масло ну и смазывающие своиства соответственно как у масла, еще я добавляю немного двухтактного масла. А так использую ка смазку для скользящих частей токарного станка, скользит прекрасно, лучше чем современная сухая соляра. Цены на новую инструкцию пока нет - инструкция в производстве, старая стоит сто америки.

[@ИванПетров-ю6я]

у меня форсунки заклинили через 100 км после использования самодельной солярки, добавка смазывающей присадки обязательна. двухтактное масло никакого влияния на смазывающую способность не имеет, оно лишь немного повышает цетановое число, на эту тему есть результаты исследований.

[@santeryi9]

@@ИванПетров-ю6я Если не очистить как следует и поторопиться то полимеры и смолы осядут в топливной системе, залепят клапана, форсунки, заблокируют насос, и тд. Я об этом говорю в своих видео, во первых после отгона надо отстоять, несмотря на прозрачность, сформируется много осадка, затем химическая очистка или отстой на сисликагеле, после хим очистки опять отстой на абсорбенте. если ест; сомнения то перед употреблением наливаем в чистую стеклянную посуду, даём постоять несколько часов и если на стенках посуды образуется налёт в виде тёмных точек - значит топливо неготово и в нём продолжаются процессы икисления и образования полимеров, они то и блокируют топливную систему. Все эти предосторожноти желательно делать до тех пор пока вы не найдете приемлемый для вас способ очистки топлива, в котором вы будете уверены. У меня одна машина бообще не видела соляры с заправки около 8ми лет, на самодельной наездил около двухсот тысяч километров, сейчас сын подрос, отдал ему он на ней ездит, намотала машина около 430000км, заводится и не дымит. В соляру как самодельную так и с заправки добавляю еще присадку для топлива моррейс, таким образом решаю возможные недостатки топлива. Всегда обслуживаю машину, меняю фильтры и тд. Но с дуру что попало заливатьне стоит.

[@thanksi2278]

Great work Sir, I will try it for vegetable used oil

[@biomechanique6874]

Use methanol instead of ethanol. Sodium methoxide is used with veg oil to make biodiesel.

[@chrisss2630]

Hi, can be used this process to clean out some residue of waste oil for LTO burner ?

[@santeryi9]

The oil must be distilled first.

[@wilharris5930]

how much money is saved??

[@santeryi9]

my home made fuel cost me about 4 dollars for 20L while gas station cost is 2.20 per liter. And it is not about saving money ow, it is about the ability to make some fuel in situations when there is no fuel available for any money, very actual in current reality.

[@samir-chaway01]

I am trying hard to excel in the success of this method, because I have a lot of burnt oil

[@santeryi9]

To use this method the oil must be distilled first.

[@sanduafaceri2792]

Alek why do you use SILICA GEL and from where did you take the silica

[@santeryi9]

Silica is for water and pigment removal, it polishes the fuel, also I am not always use silica, a heat drying and centrifuge filtration, my silica is from a supermarket - cat litter crystals.

[@IlluminatedPolitics]

Hi Alek have you ever tried sulphuric acid to clean the oil?

[@tek4]

That would be interesting but would it break the oil in to short chain hydrocarbons

[@IlluminatedPolitics]

@@tek4 interesting..but if you use it as Diesel equivalent is it bad to have short chains? I have cleaned yellow petrol station diesel with it and at the bottom settled down a brown chewish gum like mass and the diesel was white clear like water

[@brianbassett4379]

So all things considered, necessary supplies and hardware, transportation/storage of fluids, absolutely necessary clean up of contaminates, but most importantly time... it comes to what $10 maybe $15 a gallon of inferior grade fuel?

[@krithicks6206]

So what is use of the end product?

[@victoryfirst2878]

Now I know what and how to make this happen. Alek, you are the man for sure. Look forward to make this on my own. Any other tricks you have Sir ??? I would like to know fella for sure.

[@santeryi9]

Please note that this method works with distilled oil only, not the black waste oil, so you need to distill it first.

[@victoryfirst2878]

@@santeryi9 Please define distilled Sir ?? Thanks

[@alijaved3556]

Brother is it applicable for tyre oil?

[@santeryi9]

I think should be applicable. Try.

[@jediobi851]

Hello Did you tried this cleaning method for tyre p.oil? And can you please share the results. Thanks in advance.

[@saedaldeb8399]

ماهى اسم هذه والمواد ونسب العمل بها

[@vasilispants8241]

Please explain why we should get into this trouble instead of just using crude diesel oil from the distiller.

[@santeryi9]

To avoid stuck valves and clogged fuel pump.

[@Campsitecooks]

Could you please give me a list of all the equipment you use please

[@santeryi9]

I am using the oil distiller, the conical container for oil preparation and later fuel treatment, metal containers for bitumen collection, plastic containers for fuel storage, and a transfer pump with an oil filter for car fueling.

[@wetimkr]

Dose it smell like disel also or no?