If you are experiencing leaky mags or just want to give your mags a good cleaning/inspection, this video will help walk you through some things you can do to prevent or alleviate your issues.
Пікірлер: 92
@user-be1it9zi8v4 жыл бұрын
I have the old mags but this helped a lot thanks. The previous owner had wrapped the inner mag in black ducttape ffs, was near impossible to remove
@wardaddy2.0226 жыл бұрын
helped me out a lot thanks
@Mythic28277 жыл бұрын
Guess who's back... back again.. Lol Needed to rewatch this ha ha :DDD
@DouglasThompson7 жыл бұрын
Mythic mythics back, tell a friend.
@chrisvandam69513 жыл бұрын
Nice video 👍
@jameskeanu86088 жыл бұрын
very helpful!!!
@felipeesp359025 күн бұрын
Thank's!!!!!!!!!
@DouglasThompson25 күн бұрын
:)
@drukenwilli49983 жыл бұрын
get this fellow man a tissue!
@blitzline999 жыл бұрын
I didn't even know that ver 2 mags were out there.Got all mine from Evike years ago and they all pooped out and leak from both ends no matter what I have tried.I have the we vin m-16 20 round mag that works no matter what.
@DouglasThompson8 жыл бұрын
I wondered about those little mags, I was thinking about picking some of those up for prone shooting with my WE l85. Good to hear they cause you no problems! I will remember that if I end up getting a scar l or other stanag we gun in the future.
@96vmax42 жыл бұрын
I have a c02 mag for the l85 (same mag) the main valve is leaking but the valve isn't a one piece design. The pintle and rear seal come out of the mag but the seal for the pintle is built into the mag somehow. Is there a way to take that little oring out if the mag body and replace it?
@DouglasThompson2 жыл бұрын
can you send me a picture of what you're talking about? demureg@gmail.com
@Teddy_98310 жыл бұрын
this video helps but the leak on ,y version 2 are coming from the out put valve because i used to bee one that would let the gas just go rushing out of the top so not sure if its the output vale or the orings on the output valve but hopeful ill know soon. have you had this problem before???
@DouglasThompson8 жыл бұрын
The only time I suspected and experienced a leak out of the output valve is using my ghk g5 mags. there are 2 cylinders inside the plastic housing that just needed to be tightened and the leak stopped. also I have experienced the issue when I would run the mag too hard and things would start freezing. I don't recall I ever had that issue with my we mags. I currently do not own any we m4 mags.
@TangguhJatiloud10 жыл бұрын
Nice vid mate! thanks for this, i get so much nice tips, about to treat my magz a bit carefully from now on ;) ( to use adapter when refill a gas, don't press the gas striker to often or to long, make sure all the screw is snug not too tight, etc ). I got 5 WE ver 2 magazines, 3 of them is almost 2 year now, while the rest i just got it couple days ago, one of my old ver2 magz is leak on the top seal, apparently its a soft leak, cos i can hear "sssss.." sound from it, but if the magz is upside down the gas leaks more the sound is noiser than before following with the gas coming out, can it be fixed? Thanks Mate!
@DouglasThompson10 жыл бұрын
usually if you have any issues with a gas leak it can be fixed with either tightening the valves and /or screws up or replacing the oring or valve thats causing the issue. You can order gas mag orings pretty cheap online if you go to ebay there are some good deals on there. or if you can't wait, sometimes places like ace hardware will have small orings.
@TangguhJatiloud10 жыл бұрын
Hey thanks for your quick reply! i believe its not only the o-ring but something inside top seal, i will upload a vid regarding this, will let you know when it finish upload.
@DouglasThompson10 жыл бұрын
sounds good, Ill do my best to help out.
@themanthelegend70484 жыл бұрын
I am new and I just got a king arms gbb m4 (colt licensed). I was curious as I dont know, what mags will work for it? A lot of mags look like they will work, but not sure. I read that we tech ones would work but again a lot look like they will but don't wanna buy if it doesn't.
@DouglasThompson4 жыл бұрын
The we mags are proprietary. I dont know of any other companies that utilize them. King arms uses the western arms standard design so they are compatible with a lot of companies. Unless they changed it in the last few years, most western arms style mags should work with little or no modification.
@themanthelegend70484 жыл бұрын
@@DouglasThompson sweet sounds good thank you.
@paulovitor93883 жыл бұрын
@@DouglasThompson Army Armament uses WE mags for their G36C and Glock 17
@DouglasThompson3 жыл бұрын
@@paulovitor9388 very cool! Good to know
@ChaosBW6 жыл бұрын
I bought a g&g pistol that blew gas out of the mag and fired full auto mag dumps with 1 trigger pull out of the box It was a semi auto m9...
@DouglasThompson6 жыл бұрын
Meme Machine sounds like loose tolerances on a part...have you contacted G&G?
@johnathanpindak82844 жыл бұрын
I am new to the gbb side of airsoft and was wondering if you have to only maintenance the mags when their is a problem or after each game?
@DouglasThompson4 жыл бұрын
You can do it as needed but sometimes things need regular maintanence. Especially if you play games in outdoor environments. If you play mostly indoors and your mags are working just make sure they arent leakimg and dont leave them empty if they are being stored.
@jonathancharlesferriols12083 жыл бұрын
I have a question about npas on we m4? On the maximum adjustment does it increase fps?
@DouglasThompson3 жыл бұрын
If you close the valve tighter I believe it diverts more gas to the bcg and gives lower fps but more recoil. If you loosen the valve it gives the bb more gas and gives less felt recoil. That's how I remember it anyway, it's been a while since I have flexed my knowledge about airsoft so I'm a bit rusty. Lol
@jonathancharlesferriols12083 жыл бұрын
@@DouglasThompson thank u for answering my questions bro. Please make more vids for airsoft basics thanks
@DouglasThompson3 жыл бұрын
I am so far out of the loop nowadays with airsoft, I ended up stopping airsoft after my left knee surgery and my right foot needing surgery. Just can't keep up anymore lol
@GuardianMilsim7 жыл бұрын
I have a gbb v2 m4 mag and it would leak from the top. It worked fine previously. Does it just need lube or do I need to replace the o-rings in the valve.
@DouglasThompson7 жыл бұрын
Who makes the mag?
@jonathancharlesferriols12083 жыл бұрын
How true that if you remove the little rectangular plastic inside the spring it will add 5 more bb's inside?
@DouglasThompson3 жыл бұрын
That would cause major feeding problems.
@jonathancharlesferriols12083 жыл бұрын
@@DouglasThompson thank you sir. And is WE m4 RIS is a good beginners gun? I already bought one and 2 extra mags and silicone oil . Can you also make a vid on how to maintain the m4 RIS rifle
@DouglasThompson3 жыл бұрын
Thank you very much, I have a tutorial I think will apply to you. It won't be exact but it will help you out I think. Yes, the WE M4 will serve you well! :) I'll post the link when I find the vid.
@DouglasThompson3 жыл бұрын
Here you go! kzbin.info/www/bejne/Z6ekk4V9jNdpg8k
@jonathancharlesferriols12083 жыл бұрын
@@DouglasThompson thank u this really helps me on the basic maintenance of the gun. Maybe you can make vids of m4 ris guns in your next vids. Cause I heard that they said that the WE M4 RIS has many issues
@corvinusgaming6 жыл бұрын
I have a problem with the magazine that came out of the box with We tech m4. The problem is when magazine is empty the bolt does not catch back for the magazine. And if I have dry fire mode on as well the bolt does not catch back. I have tried with other magazine and it works perfectly with them. I have no clue as to why the bolt does not catch back for this magazine. It was working perfectly when I got it but after some use of the magazine it does not work now. Need some help.
@DouglasThompson6 жыл бұрын
sarbajit35 if you apply a bit of pressure on the bottom of the mag while its inserted in the rifle and fire the last round, will it lock?
@changye96047 жыл бұрын
Could I ask a question. If I want to put a free float rail in my GBBR do I need to get a low profile gas block. Or can I just leave the gas block off.
@DouglasThompson7 жыл бұрын
Chang Ye leave it off, it will make the gun lighter which in turn equates to more recoil. ;)
@changye96047 жыл бұрын
Okay thank you. :)
@jonathancharlesferriols12083 жыл бұрын
Upgrading your buffer springs on we m4 will increase your range?
@DouglasThompson3 жыл бұрын
No, it will just alter how the replica feels when fired.
@jonathancharlesferriols12083 жыл бұрын
@@DouglasThompson or maybe I can remove the metal thing inside the buffer? There is a weighted metal inside of it?
@DouglasThompson3 жыл бұрын
The weight is so the bolt carrier doesn't bounce as much when you fire the weapon. You can remove it and see if it helps with gas efficiency. It does have a function though.
@MP-zv6fm2 жыл бұрын
Hi Doug, I have a WE G26 Short 16 shot mag. I can only get a few shots in until the gas runs out. I tried filling it and it fills quick, but again after firing 4 rounds the gas is gone. Seems that the gas is not filling all the way or something is obstructing. Any advice?
@DouglasThompson2 жыл бұрын
Are you filling the gas with t he mag upside down?
@MP-zv6fm2 жыл бұрын
@@DouglasThompson I think the first time I filled it, I did fill it with the gas nozzle pointing up..
@DouglasThompson2 жыл бұрын
@@MP-zv6fm the liquid needs to enter the magazine so you have to fill with the fill bottle on top and magazine on bottom. :)
@MP-zv6fm2 жыл бұрын
@@DouglasThompson ahh gotcha.. Im such a noob 😂.
@DouglasThompson2 жыл бұрын
No problem, it's a common mistake actually. :)
@mattl.70734 жыл бұрын
Hey bro those WE magazines could be used in a KJW C8 GBB???
@DouglasThompson4 жыл бұрын
We tech uses proprietary mags. They most likely will not work with the Kjw.
@kosmouz8 жыл бұрын
hi bro; thanks for the video.i have a problem; no leaks or nothing like that; i fill the mag fully with gas and bb's.when i pull the trigger the pressure is way too much.after 7-10 shots the gas goes empty.and sometimes the opposite.the gas doesnt flow good at all which causes blank-fire. i am assuming this might be a problem from trigger or mags? would be nice to have an answers. btw using we416 gbbr may the accuracy be with you
@DouglasThompson8 жыл бұрын
Are you filling the mags with the gas upside down? the fill valve should be pointed up.
@kosmouz8 жыл бұрын
+Douglas Thompson hey man.of course i do fill the mags properly.is it more likely to be a valve problem,or the trigger? My bolt is ra-tech but trigger is stock.if the trigger-piece not hitting the valve properly;maybe it causes gas pressure inconstantly?
@DouglasThompson8 жыл бұрын
Does the gun do the same amount of rounds with the stock bolt installed? Also I apologize, I wasn't insulting you or anything, just got to go down the possible checklist. I was going to ask if your hammer spring was upgraded and possibly releasing too much gas per shot...but you already answered that question. Are your shots abnormally high fps?
@DouglasThompson8 жыл бұрын
What state do you live in and what is the weather like when you're experiencing these problems?
@kosmouz8 жыл бұрын
+Douglas Thompson thnx for the replies brother.it is not really cold where i live.no snow;only cold like 1o C maybe when its colder like 5 C ...i have no chrono at home but As i record slow motion with my camera; either the bolt doesnt move properly back(i think low gas flow) OR bolt cycles really good with too much has release(which causes the 10-12 shot emptying the gas inside mag)
@tiagofurtado256 жыл бұрын
whats the name of the tool that you use to tighten the valve?
@DouglasThompson6 жыл бұрын
Tiago Furtado i think its called an airsoft valve tool. Not sure Ill se if I can find a link.
@tiagofurtado256 жыл бұрын
when i turn my magazine upside down the gas leak faster, i think is the hammer valve, what do u think?
@firefox127028 жыл бұрын
im having a problem that i cant seem to find what is causing the leak. the leak looks like it is coming from the top of the mag where the gas would be released into the gun for it to shoot. The leak is very slow but is still noticeable. I have completely disassembled the mag looking for a problem and couldnt find anything. I shoot at about 400 fps (not sure how many joules) with the npas installed. Thanks
@DouglasThompson8 жыл бұрын
have you tried disassembling the striker valve assembly? possibly a weak spring or a bad/ and or dry oring.
@firefox127028 жыл бұрын
Douglas Thompson I haven't been able to disassemble that part because I don't have the proper tools any suggestions of what tool to use I haven't been able to get it with a screwdriver like the fill valve
@DouglasThompson8 жыл бұрын
+Eddie Lee Lol, I don't have the proper tool for that either. Just a very small flathead screwdriver like the ones you can get in eyeglass repair kits for removal. For re installation a large flathead screw driver works nicely. I can make a small video on the subject if you need a visual representation.
@firefox127028 жыл бұрын
Douglas Thompson ive tried with a flat head and i cant seem to get it unscrewed the button that releases the gas wont depress far enough for me to get a flat head and unscrew
@DouglasThompson8 жыл бұрын
+Eddie Lee You know, I was thinking about the c-clip... You do have to get a special tool to unscrew the entire assembly. You can make one if you have a flat piece of steel large enough and just cut some material out of the middle. I have successfully made a couple. Again I can show you how if you need further instruction. All the valve tools I've purchased break quickly so you're better off making your own if you have the knowledge and a Dremel.
@tiagofurtado255 жыл бұрын
hey douglas, you are my only hope. so... i lost a piece of my m4 magazine. that piece in the magazine that locks the bolt when its empty. i need tha name of tha piece because i need to print it on a 3d printer
@DouglasThompson5 жыл бұрын
What magazine are you using specifically?
@tiagofurtado255 жыл бұрын
@@DouglasThompson m4 open bolt series
@anthonyestrada4422 жыл бұрын
Do you got any hand pistols you want to sell
@DouglasThompson2 жыл бұрын
I might sell some of my airsoft guns. Maybe all sometime soon actually. I have been thinking about it.
@ErgonomicChair5 жыл бұрын
"Make sure to get the plastic adapter, it will eat your orings." *Proceeds to use metal magazine tool.* Lol okay bud.
@mabstaanderson27677 жыл бұрын
Mine leaks out the top
@DouglasThompson7 жыл бұрын
Brian Anderson If you take the bottom off you should be able to tighten the magazine screw that seals the gasses. If I still had the mags I could help you out more....
@jamesfulmer70806 жыл бұрын
I have a odd question. I have gas mags that I've had for several years and have never put gas in them. Will I need to do anything to them or will they work when I finally use them?
@DouglasThompson6 жыл бұрын
James Fulmer id say fill em up super wet as in tons of silicone oil. Let the orings get a taste of oil before you rely on them.