Whirlpool Washer Repair - How to replace the Lid Switch

Need help replacing the Lid Switch (Part #3949247V) in your Whirlpool Washer? Watch this how to video with simple, step-by-step instructions for a successful DIY repair.
Stay safe during your repair! Be sure to check www.fix.com/safety/ for proper safety procedures before you begin. Use of this video is at your own risk, without liability to Fix.com.
Fix Part Number: FIX11722098
OEM Part Number: 3949247V
Why you might need to replace the Lid Switch:
1. Lid Switch not working/broken Lid Switch screw holes
2. Washer stopping on rinse and spin cycle
3. Washer will not drain
4. Washer will not turn on
What tools you need for this repair:
• Phillips screw driver
• 5/16 Nut driver
The information in this video is specific to Whirlpool, KitchenAid, Kenmore, Roper, Inglis, Estate and Crosley. To find a Lid Switch specific to your model, visit www.fix.com
Not what you’re looking for? For more washing machine repair help click here: www.fix.com/parts/appliance/w...
Where you can buy this part:
www.fix.com/parts/washer/whir...
Connect With Us!
/ fixdotcom
/ fixdotcom
plus.google.com/+fixdotcom
/ fix.com
Visit our blog: www.fix.com/blog/
Don’t forget to comment below and subscribe to our channel!

[@78zambo]

I thought our ancient washer was done for today... I pulled the lid switch and it literally dissolved in my hands. The beast lives on! Thanks for the great video.

[@rahulnaruula]

Thank you so much sir!! My machine wasn’t draining and spinning. My repair guy told me the fault was in drain pump and quoted me $250 to replace that. Then my quest to change the drain pump started since I found one for $27 on Amazon. That’s when I went suspicious of my repair guy and stumbled upon this video after watching the other video of yours ‘ how to replace drain pump’. After watching this video, I thought what if the fault is in lid switch and to my surprise it was indeed faulty. I replaced the switch by myself and want to thank you for saving me $1300 since I was thinking of buying a new machine instead of getting it repaired

[@kendradaringgreatly6411]

45 minute repair for a first- timer and in a tight space. Very helpful video!

[@rmobe]

I was going to buy a timer but the parts guy said check the lid switch. Saved me $220 new timer was $250. This video made it easier than I thought, Thank you!!!!

[@ruthannrickey9475]

What was your washer doing? I’m trying to figure out if mine is a lid switch or timer. Figured I’d start with the cheaper of the two. But curious since you specifically said the two parts I have narrowed my problem to.

[@robertkennedy6485]

Thank You for the video! I am the very definition of un-handy & I was able to fix it myself after watching the video.

[@homelee665]

Even though there were a couple of differences between this and what I have, it made the process a lot simpler.

[@DJ_InYourFace]

Just prolonged the life of my Whirlpool Ultimate Care II. Thanks.

[@jerrycleveland2812]

Excellent! My Whirlpool washer had the two console screws on the front but everything else was similar.

[@richardgriggs1183]

Wow you made this super easy thanks

[@shanell_888]

Thank you!! Saved alot of money 🥳💙

[@dosmastrify]

Thank you sir!

[@jacekbrzeszcz2412]

Thank you 😊

[@wyjode27]

There is a steel plate all the way up back of machine and 2 nuts I undid but top with controls will not slide a little forward and bend back! There are not screws? What do I do?

[@dosmastrify]

7:30 hardest part by far. How should back look?

[@Kambic79]

Seeing what you are doing is important in assuring everything is taken apart and goes back the way it should. That being said, I think the only thing not really shown was putting the cabinet back into place after having fastened the switch to the cabinet; (7:15) There is mention of aligning the lip but visuals would have been nice. Otherwise, great video!

[@pollipetersen6557]

I agree. I’m having the same issue right now.

[@brandonterry4638]

Yeah I'm not going to have room to even pull the frame off so I'm about to do some sketchy shit

[@Kakkydidit]

I have NO screws visible when lid is lifted. Must be a way different model.

[@jalabar832]

Can't see what you're doing!

[@Inhimwelive]

It's pointless to say whirlpool washer without the model, they are not all the same.