Why my Mower keeps throwing deck belts.

[@MrTL117]

Buying the more expensive belt will save you the time and hassle of dealing with the cheaper belts. The more expensive belts have kevlar fibers intertwined within the rubber which gives the belt a much longer life than your usual run of the mill belt. This was the case with the blue colored belts I sold back in my hardware days. One thought, if you went through the hassle of changing the belt it might be a good idea to grease those pulleys if you can and check your bearings on the deck. Keep up the good work.

[@HomeGaragechannel]

You're absolutely right. Thanks for the comment vintage fixer I appreciate it.

[@AlphaAl1]

That’s a great tip I hadn’t considered. Thank you

[@charlesbrown4483]

I have a John Deere gt235 that I mow about 4 acres of land with every 5-7 days. I live in a very mountainous area and so very little of the land I'm mowing is flat and even. It's very rough on the mower, steep and bumpy everywhere. So I've found over the years that it's better in the long run to buy the cheaper belts. Mowing as much grass as I do on rough terrain means you're going to burn through belts no matter what. I can get 3-4 cheap belts for the same cost as 2 of the nice reinforced John Deere branded belts, and they end up lasting about the same amount of time either way. But if you just have a small plot of flat land to mow then the expensive belt would be the better choice.

[@michellealms3238]

I kept breaking belts off my new JD 130. The 3 rd time repair man refused to do it. Told me bring it to JD dealer. Moral of the story nearnest JD dealer is hour away and I spent a lot already on belts and labor! I went to Lowes bought JD brand belt. Went on utube watched few videos and Put dam thing on myself. Apparently repair man wasn’t using J Deere belts I quickly noticed as I saw old belt looking for replacement number. Two years and still same belt I put on👩‍🔧sure is a good feeling when u can avoid those labor costs!

[@HomeGaragechannel]

thank you Michelle Alms for sharing your experience.

[@MultiTurbospeed]

10 years on one belt for me and will replace it with the next 2 years

[@tomw8656]

Thanks for the video. John Deere D105 37 hours. 22 belts. 3 times by me to John Deere repair shop. I classify this tractor as a POS.

[@HomeGaragechannel]

Thanks for sharing

[@jlda1887]

John Deere mowers are rubish...

[@MultiTurbospeed]

@@jlda1887 not really. As long as you check it and clean it regularly it will last for decades.

[@MultiTurbospeed]

I learned this little bit of advice about belts. Test it first if you smell burnt rubber or see smoke then it's wrong. If you don't smell or see smoke then you got it correct.

[@alssmallengines]

Great video 👍 I buy the renforced belts for my tractors. But when buying them for tractors I'm going to fix & flip I buy the cheaper ones.

[@HomeGaragechannel]

Nice answer. I totally understand. Thanks Alan Marshall for the comment I appreciate it

[@kylergriffin]

Well done video. Very helpful. Guys like you are what make KZbin a great resource. Thanks!

[@HomeGaragechannel]

Thank you Kyle Griffin

[@ronaldpugh7679]

I have to thank you for this video. I've been looking for one that shows how to put deck belt back on. Went to two John Deere dealers, and because it has 5 pully's, they kept giving me the wrong way to install. Your vide explained it very clearly, and kept me from having a nervous break down. Thank you so much.

[@HomeGaragechannel]

No problem and thanks for the comment I appreciate it

[@Brian424]

My John Deere L111 with the 42 inch deck just broke the belt for the first time today (May 28, 2022), 16+ years and over 450 mowing hours since I bought the tractor brand new in 2005. I'm picking up the OEM belt tomorrow (almost 50 bucks for it), and here's hoping it lasts as long as the factory original. The tractor has the 20 HP V-Twin Briggs engine and still runs perfectly and uses/burns no oil. The oil is still very clean on the dipstick at the end of the season. I install the factory maintenance kit with new oil and filter, spark plugs, fuel filter, and air filter, every year at the start of the mowing season, and so far, so good. I mow about an acre of grass here, with 25-30 mowing hours per year on the tractor, depending on how much rain we get. Mowing season is about six months long here in Wisconsin, again, weather dependent, mostly based on how the April weather pans out First mow of the year happens anywhere between April 20 and May 10, and the last mow/leaf mulching run is usually around October 20. Thanks for the video. It will help out tomorrow when I'm crawling around and cussing while putting the new belt on.

[@HomeGaragechannel]

I appreciate Brian.

[@Brian424]

@@HomeGaragechannel Right after I finished replacing the blade belt (which went smoothly), I went to start mowing and found my two front tires pointing in different directions. One end of the tie rod (John Deere calls it a drag link) on the right side wheel had worn out and picked that moment to fall off the ball joint. The rod and ball joint are press-fit at the factory and once the connection wears enough to come apart, there's no fixing it. So yesterday I picked up the two new tie rods for both front wheels, to the tune of $122. What are the chances of two breakdowns right on top of each other after all these years of no trouble with the tractor? Oh well, another repair I get to do in the next couple days.

[@MultiTurbospeed]

@@Brian424 that happened to me just took a 2 medium zip ties and tied it up and it drove fine until I decided to retire it for a new one

[@fredhart7904]

My experience, I have a small JD mower just like the one in your video, I bought a cheap deck belt off brand, it was a waste of my time, I when back to the dealership paid more, but got a quality belt, Counter guy said belts that have to run in uneven planes like a mower deck must be built to higher standard for flexibility than just a straight running belt, He must be right as I have had no problems with the JD belt,

[@HomeGaragechannel]

Excellent. Thank you for sharing your experience. I appreciate it.

[@nellienelson2111]

Same problem for me, I bought an off brand belt, snapped after 5 hours, I bought a JD belt, no problems. The kicker is the off brand was actually more expensive. What I didn’t know was JD is metric, off brand is not.. lesson learned.

[@bertgrau3934]

I use cheap belts, they will last a season, and I can buy 3 cheap belts for the cost of a better belt, that's just me , every winter I take the deck off and clean, replace bearings if needed, remove rust and repaint. It make the deck last much longer, I have a 2005 Murry 40 inch mower since new, the engine gave up, but the rest of the mower is in very good shape. I also replaced the 12.5 engine with a 2 cylinder 25 horsepower Kohler Pro engine it can cut tall grass/weeds with no problem.

[@HomeGaragechannel]

I like that idea, makes sense to me. Thank you Bert Grau.

[@AlphaAl1]

My next belt will be a higher quality belt for sure. Great video and input. :))

[@HomeGaragechannel]

Right on!

[@theresamoore7634]

Build up wet grass around the main pulley & on top of the deck would cause the belt to slip off the pulley also , Keep Cleaning out the grass would help to keep the pulley in place Lol Hope this helps

[@HomeGaragechannel]

thank you for the tip

[@Bradmeiser]

It drives my OCD nuts when I see a deck covered with grass like that it's not that hard to clean them off after each mowing... I always use kevlar reinforced belts..

[@HomeGaragechannel]

lots of grass on the deck can be very bad for it. definitely blow it off whenever possible

[@MultiTurbospeed]

What I hate is when a battery goes bad it will cause the pullies to rust within days to weeks and will have to be replaced plus all the other hardware

[@electroddxful]

I would buy a reinforce belt for myself. Great repair 👍👍 👍

[@HomeGaragechannel]

Thank you RayFpv for the comment I appreciate it

[@georgestrickland9278]

lt 133,great mower,good engine,5 speed manual trans,only problem hoods were junk

[@HomeGaragechannel]

yes I have to agree with that.

[@davehaggerty3405]

Worn pulleys will shorten the life of even superior belts like Gates or Stens. If your pulley is shiney all the way to the bottom of the groove, it is worn out. Misaligned pulleys or bad bearings will damage belts. Belts are more often a symptom of a problem than the cause.

[@HomeGaragechannel]

I couldn't have said it any better

[@bluegrassman3040]

I’m replacing all the idlers and spindle pulleys on my deck on my LT166 48C. The mower is 22 years old and they’ve not been replaced. All of the insides of the pulleys are shiny and worn unevenly. I replaced e belt last year and it wouldn’t last but maybe an hour, as it threw the belt off while I was mowing with it.

[@maj3stikq122]

Why would it keep throwing brand new belts? I’ve put 2 in and it threw them both times within 5 minutes

[@HomeGaragechannel]

the belt isn't the problem then. I would look at the idlers and tensioner pulleys for wear, this wear would allow some slop and the slop could be enough to throw the belt.

[@always_something]

At the end of month 1, and my 3rd cheap belt. I put on a reinforced belt for 2 years of worry free mowing. In a pinch, I will use a cheap belt, usually due to awaiting the reinforced belt to arrive.

[@HomeGaragechannel]

that makes sense, thank you Dale Booth.

[@barryjohns1965]

Deck belt does the exact same thing on my E100. I have tried four different brand new belts, I bought te updated bracket for the front Crank shaft pulley. Still comes off every time you disengage the blades. The adjuster is welded so I fixed that issue by taking slack up in the cable that didn't work so I bought the recommended john Deere belt that is 103" instead of the factory 103 3/4". Still same issue. Then john Deere makes a plastic bowl shaped retainer that mounts to the crank shaft pulley so I bought that and still no fix, Then I replaced every pulley and every idler arm bracket on the deck, still same issue. Mower has 49 hours on it and I have been a small engine and mower mechanic for over 20 years. This has to be a recall but they say no. John Deere needs a suit against them for the E100.

[@HomeGaragechannel]

yes it seems to be a real issue.

[@jeffhagberg6796]

OEM only, saves my nerves!

[@HomeGaragechannel]

Thanks for the comment I appreciate it

[@DiscipleoftheDumbOx]

My issue currently is my lawn tractor throws the belt after engaging the mower. I've replaced the belt so it may be one or more of the pulleys.

[@HomeGaragechannel]

yes it's probably one of the pulleys or the tensioner. Can you also confirm that the belt is the correct size for the deck.

[@amandasanders9130]

We have the same issue. Have replaced the pulleys, adjusted the tensioner and bought oem belt. Still falls off when you engage, not all the time, but almost always when you are trying to out run the rain. 🤣

[@HomeGaragechannel]

@@amandasanders9130 do me a favor, next time you use it, slowly engage and disengage the PTO for the blade, it's almost 99% sure that it won't chuck the belt

[@MultiTurbospeed]

@@HomeGaragechannel idle down the throttle to 30% and them turn on the pto. I'm lucky I can crank them up at running full rpm and not even a slip

[@roystheboy]

I did a john deere x125 fir the first time last week where the belt kept coming and eventually snapped so i told the owner to buy one from a john deere shop and now works great and he asked to give it a service & hes SP mowers to

[@HomeGaragechannel]

Thanks Roy's the boy for the comment. Yes OEM belts seem to be pretty strong

[@WatchMeSpore]

Good work. Thanks for being clear.

[@HomeGaragechannel]

Glad it was helpful!

[@halcampbell1384]

For deck drive, always buy OEM. They are designed to accommodate the shock loads that replacement belts can't handle. In this case you get what you pay for.

[@HomeGaragechannel]

very true

[@alesawilliams1491]

33dd#²$/=e...n;nnnnn. ÷

[@themowerman]

Sometimes changing the pulleys can help

[@HomeGaragechannel]

Thank you Micks Mowers I appreciate it

[@brandonwilliams998]

A question about my L111, why is my deck twisting belts? 3 belts replaced and the twist. Any help would be greatly appreciated.

[@HomeGaragechannel]

sure, more than likely one for more of your pulleys on your deck, is either out of alignment due to bearing wear or the deck having issues. the other would be your deck, is uneven or crocked in relation to your Frame.

[@Patrick4959]

Buying the more expensive type is mostly better because your avoiding to replace it longer in the long when mowing grass when you need to engage the engine and pulleys combined etc

[@HomeGaragechannel]

That is very true.

[@Patrick4959]

@@HomeGaragechannel too right mate

[@thomasmiller1286]

kevlar does wear longer ,,,but if theres a belt drive problem it dont really matter better belt or not both will brake..

[@HomeGaragechannel]

very true Thomas Miller.

[@jaluna06]

Nice vid. I would prob spend the extra money if the life of the belt was for sure more than the cheaper one.

[@HomeGaragechannel]

Thank you for the comment I appreciate it

[@kevinbrister8801]

I have the l110, The last time I mowed the belt that I had recently purchased from JOHN DEERE came off and actually shredded luckily I had an old belt and after mowing for about 2 laps it came off. Come to find out the engagement pulley lost the bolt. So I found a bolt in my bin and replaced it. After I got it on and working I finished mowing. When I went to put the mower back in storage i noticed that there was a little patch that is always hard to get to. So I went to engage the blades to cut it and mower died! So Im gonna spend a lil time today and see what the problem is! Hooefully nothing too serious. I can't afford much so maybe a simple fix like the pulley is locked up! Also what would cause the blades to turn slowly when its not engaged?

[@HomeGaragechannel]

i would check to make sure the belt hasn't come off of a pulley and is jammed. otherwise check one of the safety switches.

[@kevinbrister8801]

@@HomeGaragechannel I just spent about an hour checkin put. Seems that one of the spindle pulleys is gone/froze up $50 and also my pto cable is stretched $25 hopefully for about $100 I can get a new spindle pulley, pto cable and a belt! Atleast the new spindle will come with a grease insert! I know that bcs I had to replace the other one 2 yrs ago!

[@HomeGaragechannel]

@@kevinbrister8801 great diagnostic work. Thanks for the update I appreciate it

[@replynotificationsdisabled]

I think it's mostly from dropping/raising deck when blades are engaged.

[@HomeGaragechannel]

Yes I agree, that has something to do with it as well.

[@sgtjameslindsey2493]

Thats what happened with me, the hand guage jumped out and the deck slammed down causing my belt to jump a pulley

[@WayToManyAssassins]

I'm guilty of that 😅😅

[@tonym6920]

Looks like that mower has seen better days. Buy cheap, get cheap!

[@HomeGaragechannel]

It's on its last legs. Thanks for the comment

[@Jim-ie6uf]

What caused the skinned part on the old belt? I’ve used OEM or aftermarket Kevlar. Couldn’t tell a difference.

[@HomeGaragechannel]

I think the belt was worn away by the drive pulley when the blade was disengaged.

[@jgagatch]

I bought an aftermarket belt and wound up here wondering what the hell is going. I am going back to OE

[@HomeGaragechannel]

I can look up the part number if you have the model and serial number.

[@petercondo2007]

My mower belt (new ) comes off after a few minutes of cutting. Any ideas on what to do?

[@HomeGaragechannel]

Where did you get the belt? I just to make sure the belt is the right length. Otherwise you need to check the pulleys and make sure one of them isn't worn out or misaligned.

[@nunya___]

John Deere decks have a tension adjustment. Follow the cable down to the deck and with 10mm wrench loosen and adjust. Also with John Deere lever-arm, release the blades _SLOWLY_ and at low RPM.

[@richardhetrick4770]

Trade it in I bet it is tensioner pto not electric

[@bradesteve2077]

@@HomeGaragechannel what if rhe deer don't have adjustable bolts for cable

[@philfalz01]

i would buy the better belt cheap always cost more in the end

[@HomeGaragechannel]

Great call Phil falzone sr I appreciate it

[@Bigdeerman1918]

I LOVE JOHN DEERE I HAVE A D120 AND Z355R ZERO TURN MOWER

[@HomeGaragechannel]

very nice, thank you Johnny Freeman.

[@lewiemcneely9143]

Get the good belt or the cheap one will bite you. I'm going on 7 seasons with mine and not even ready to swap out yet. Tips for pulleys. If it has a groove, the 'V' part of the belt will go down into it but if no groove, the flat outside will ride on it. And the hood might have an air scoop inside to direct outside cool air into the screen intake. And I have a Kawasaki 6 horse off a Deere mower on the Snapper, hence a Kawasnapper! Thanks, Happy Thanksgiving and BLESSINGS 2 U!

[@HomeGaragechannel]

you make a good point.

[@lewiemcneely9143]

@@HomeGaragechannel I've had to figure out belt patterns on decks myself so I've been where you were. And making sure the guides were set so the belt couldn't slip off but yours was worn so thin a guard wouldn't touch it. Been there and seen that too. Blessings!

[@robertmailhos8159]

So the belt routing guide on the mower deck was gon oh no that's not cool thank God for the interest ☺️ I would buy the better belt

[@HomeGaragechannel]

Yes its probably been washed off by years of cleanings. Yes the better belt is the better option.

[@robertmailhos8159]

@@HomeGaragechannel see you later young man and your family happy Thanksgiving also don't eat too much turkey 🦃 we both know that it will make you find the recliner and go napping

[@HomeGaragechannel]

@@robertmailhos8159 already there now.. happy Thanksgiving too

[@robertmailhos8159]

@@HomeGaragechannel okay thanks for your reply young man and your family

[@richardhetrick4770]

I would buy reenforced belts if I am keeping mower but ii am selling it op for cheaper belt why can't they use two belt system like gilson some tractor it trouble free other trouble why can't they but grease fittings on idlers it is ones that tendon to turn blades on not electric pto that act up

[@HomeGaragechannel]

easy answer, cost cost cost.

[@benvarela134]

ReInForced always for a lawnmower, especially this one.

[@HomeGaragechannel]

thank you Ben Varela for the comment.

[@Howleebra]

The Fatal flaw of all these systems is stretch...as the belt stretches you have to continuously adjust it over and over. These systems should use multiple small belts rather than one giant long one because that would reduce the amount of stretch

[@HomeGaragechannel]

that makes sense.

[@bluegrassman3040]

Also check your pulley wear.

[@Howleebra]

@@bluegrassman3040 what pulley do you think is most likely to give you trouble the flat ones or the grooved ones? I'm thinking it must be stretch because mine fails in different locations... I assume if a certain pulley was to blame it would consistently fail off that pulley

[@bluegrassman3040]

@@Howleebra it’s hard to say, really. I replaced every pulley on my LT166 JD mower. It has the 48C deck. The only pulley I did not change was my crankshaft pulley. I also had to adjust my PTO clutch engagement tensioner. But at least one I’m of my idler pulleys had a bearing that was going out, but each of the grooved pulleys had wear on the inside. I was having issues with it eating belts while it was mowing. The last belt I put in it was a JD belt I got from Lowes, and it’s been staying on so far.

[@rubenavilessantos7174]

I got a D110 John Deere lawn mower and the cable to adjust the belt is welted to the blade casing how can adjust the belt

[@HomeGaragechannel]

It shouldn't be welded. Did someone weld it before you got it?

[@davidbeard1115]

I would use a 1/2 by 114 kevlar belt

[@HomeGaragechannel]

thank you David Beard.

[@Buck1954]

That's a crazy looking blade at the end. Is that jagged shape intentional?

[@HomeGaragechannel]

Yes its some kind of mulching blade.

[@timwagers4685]

Yeah it’s a mulching blade and I thought the same thing lol. Looks like it’s hit a few wires in its days lol

[@wildmanmark12]

I got a new expensive belt and it still comes off. Most if the time while I'm cutting the grass. It always comes off 20 seconds after engaging the blades. So I know it's not the belt. I just haven't figured out what's causing it yet.

[@HomeGaragechannel]

after that, I would look at the pulleys, One or more of them, might be crocked

[@wildmanmark12]

@@HomeGaragechannel that's what I was thinking. Hopefully I'll get a chance to find out one day when I'm off work and have the time to check

[@rolandboissonneau7987]

Always buy the best part you can afford.

[@HomeGaragechannel]

good advice

[@MrCjh69]

I have a 2012 John Deere Sabre. I have to replace that belt every year.

[@HomeGaragechannel]

That a shame. Does it break or just wear out?

[@coreyhoward781]

Just wears out

[@tntreviews3602]

having the belt Gard helps Gide the belt

[@HomeGaragechannel]

thank you!

[@leedanielson7452]

I had a Husqvarna and a cub cadet combined for 23 years never changed the belt and never had a belt come off once....

[@HomeGaragechannel]

wow that's pretty amazing

[@leedanielson7452]

@@HomeGaragechannel Yup!👍

[@derekobidowski3301]

one of the last great engines Kohler ever made the Command. the new twin cam Courage engines im told aren't that great. as i got a JD X350 with a Kawasaki V twin it still runs after over 200 hours on it. as Kohler and Briggs & Stratton the quality has fallen in the new motors mainly Briggs & Stratton some of their engines have plastic componets in them. if the machine breaks keep this engine save it if u have to swap the motor.

[@HomeGaragechannel]

I absolutely agree with you.

[@joekrupp1]

I put a new belt on my lt133 John Deere and smelled burnt rubber. Wasn't sure what it was and the belt snapped about 10 minutes later. I followed the diagram on my deck to install it. Could it have been too tight to start and that is why it wore through and snapped. It seemed like most of the pullies were hot also. Not sure exactly what happened there. Also can't find a real good diagram on installing it. Thanks!

[@HomeGaragechannel]

did you confirm the all the pulleys including the idlers, spun without any issue?

[@jamiehayman1879]

you dont need to "time" the blades? I was under the impression they should be 90 degrees to eachother.

[@HomeGaragechannel]

I've tried to time them an I never noticed a problem without timing them.

[@denali9449]

Belt driven blades will never retain their positioning relative to each other. Blades will, on occasion, need to run at slightly different speeds. First they do not start and stop at the same time and there is always that heavier clump of grass or catching that 3.5" high stump with the deck at 3".

[@sherrylorraine3315]

Thanks

[@HomeGaragechannel]

No problem

[@silasaqui8833]

Would help if they clean their deck once in a while😅

[@PG_Mechanics]

I would get the reinforced belt

[@HomeGaragechannel]

That's probably the better option. Thanks for the comment I appreciate it

[@jazalessandro3094]

go kevlar belt everytime,but man,I feel sorry for that ride on,needs loads of tlc :/

[@HomeGaragechannel]

You won't believe how much it needs.

[@henrysmith8012]

The Amazon belts will not hold up. Buy the OEM kevlar belts.

[@HomeGaragechannel]

you are correct

[@flipicaneze]

That number at 1:25 isn't a part number. It's an ASIN, Amazon Standard Identification Number.

[@HomeGaragechannel]

thanks for the information

[@janemariehoward]

Mine threw a brand new belt.

[@HomeGaragechannel]

Have you checked all the pulleys?

[@cdos9186]

With the condition of the mower I would have checked the oil even though that wasn't the problem.

[@HomeGaragechannel]

That's always a good thing to do. Thanks for the comment I appreciate it.

[@joeschapker9631]

I buy my belts from a John Deere dealer, then i should have OEM products.

[@HomeGaragechannel]

Absolutely. You're doing it right. Thank you Joe Schapker for the comment I appreciate it.

[@ScottyPimpinATL]

Still have my 01 l110 in mint condition

[@HomeGaragechannel]

wow nice

[@BeachLover-kn5ov]

Id love to know how to fix the belt slipping prob and u mentioned the PTO cable which I replaced as well as belt. Do u have a video on the PTO cable?

[@HomeGaragechannel]

there are only a few reasons why a belt would slip, the belt is the wrong size, the belt is ran the wrong way thru the pulley, or one of the bearing is causing so much drag that it's causing the belt to slip on all the other pulleys. So I haven't had to replace the pot cable yet.

[@perryclemons7155]

My belt keeps coming off when I go to use the blades

[@HomeGaragechannel]

Check that the belt isn't damaged and then check the pulleys. They may be damaged or out of alignment

[@perryclemons7155]

@@HomeGaragechannel I jest put a new belt on it thanks John deer am trying to stay away from they want 105.00 an hour to work on it

[@HomeGaragechannel]

@@perryclemons7155 wow thats a lot

[@sgtjameslindsey2493]

Since I don't like manual labor and getting my hands dirty. I'd buy the better belt so I wouldn't have to do that but every few years,lol

[@HomeGaragechannel]

that's a great choice

[@danielthomas3127]

I have a John Deere L111 automatic it runs and mows good the problem is when I let the break/ clutch pedal out something under the mower starts rattling and then when I push the pedal back in it stops the rattling noise would you have a idea what it might be?

[@HomeGaragechannel]

does it alway rattle then while it's moving? If so it could be as easy as the idler pulley's bearing is coming apart, or worst case it's something in the transmission. Can you localize the rattles approximate location?

[@danielthomas3127]

It is under the center where the belt's and it rattles until the break,/ clutch pedal is pressed

[@HomeGaragechannel]

the only thing I can guess a pulley

[@danielthomas3127]

I will check all of the pulleys

[@HomeGaragechannel]

let me know what you find.

[@johnrichards3235]

Why does your lawnmower blade have jagged teeth I’ve never seen a blade like that before?

[@HomeGaragechannel]

the jagged part, is on the back side of the blade and it's for mulching.

[@johnrichards3235]

@@HomeGaragechannel I made mention of that because I’ve never seen any bleed like that not even a mulching blade. Does a dual good job?

[@HomeGaragechannel]

yes it does, I would recommend them.

[@24space310]

i wouldnt care about the hood since it might get damaged or get dents.

[@HomeGaragechannel]

that's a very good way of thinking about it.

[@JT01_902]

I'd buy a re-enforced 42" belt for my LA110 in a heart beat and pay whatever the hell anyone wanted to charge me for it if i could find one. I go through 2-3 cheap amazon belts each summer and it's starting to drive me absolutely bananas!!

[@HomeGaragechannel]

I hate to say it but this belt only last 3 seasons, so I might go with the reinforced belt too.

[@JT01_902]

@@HomeGaragechannel 3 seasons would be a dream.. I can’t get my belt to stay on for 3 minutes LOL.. I suspect I have other issues that’ll need to be investigated

[@HomeGaragechannel]

I would consider removing the deck, and inspecting all the pulleys, because one of them might be mis-aligned.

[@janetrandle6882]

Reinforced belt for sure

[@HomeGaragechannel]

thank you Janet Randle

[@danielsong1323]

reinforced belt cuz the cheap belt will break faster.

[@HomeGaragechannel]

You are absolutely correct

[@brianbelanger5425]

Just purchase a new mower

[@HomeGaragechannel]

Thanks for the comment

[@ricktoole9991]

I don't think I would buy a Jon deer

[@HomeGaragechannel]

then what would you buy instead?

[@ricktoole9991]

@@HomeGaragechannel huskvarna

[@billhendrickson5506]

@@HomeGaragechannel Cub Cadet. Feedback from JD owners is bad or no service from the dealer shop. I have over 700 hrs on one Kohler engine. Never uses a drop of oil and starts summer and winter in a heart beat. I have a lawn service where I run 2-3 hours steady without shutting off in between. I wanted a JD but the negative feedbacks turned me away. There two different JD lawn tractor price ranges to buy from. The big box store sells the cheap one. The JD dealership sell the expensive one.

[@chickensfloat7427]

We have a d105, its a peice of shit. Dont buy a residental one, 80 hours and everythings taking a dump

[@HomeGaragechannel]

wow,.. that's a real shame. thank you Sam Stewart

[@MultiTurbospeed]

That is why I buy a mower from an actual John Deere dealer I can get 15-20 years worth out of them before I retire them once parts are discontinued.