Why these lock washers are the only ones that actually work! Nord-Lock

  Рет қаралды 206,661

Stephen Cox

Stephen Cox

Күн бұрын

THE ONLY LOCK WASHER THAT ACTUALLY WORKS!!!
Todays video I show you how Nord-Lock washers work and why to use them! Go to their website and order you someof the best lock washers in the world!
www.nord-lock.com
CONTACT Bruce Hudson with NORD-LOCK with any requests
bruce.hudsonii@gmail.com
"We do offer them in carbon steel with zinc flake coating, for general use; 316L Stainless; and a special 254 SMO for Oil & Gas applications (or high chloride environments)
In standard production, we offer carbon steel from M3 up to 5”; stainless M3 to 3-1/8”; 254 SMO M3 up to 1-1/2”
Donate to my patreon www.patreon.co...
Instagram / stephencoxyoutube
Or buy a t-shirt www.teespring....
Follow me on ...
Twitter / scoxyoutube
Facebook / sphinx4785
instagram / stephencoxyoutube
Check out all the itmes in my videos here www.amazon.com...
This is why the video footage is smooth amzn.to/2zLAXKs
GoPro that I use amzn.to/2yPdfd9
bendy tripod thing amzn.to/2ip7fSm

Пікірлер: 62
@SkateSpace2012
@SkateSpace2012 4 жыл бұрын
Did use a M14 Nord-lock enlarged version (NL14sp) for my variator fan nut CVT transmission scooter, seems the only way not getting loose nut on this high vibration and heat cycling location. Ordered directly (4 pairs in blister pack) from the factory in Sweden Nord-lock webshop. $10+20 UPS sending worldwide to me in Bali, Indonesia.
@Mtaalas
@Mtaalas 11 ай бұрын
I've always loved the simplicity of that idea. As long as you tighten the bolt correctly (using torque wrench) when installing and use two washers if it's nut&bolt... they will NEVER come loose. Bolts always come loose because it's more preferable for them to do so. It's very VERY unlikely that bolt with tighten ON IT'S OWN so they will ALWAYS come loose eventually... unless you use locking wires, or these...
@pyroromancer
@pyroromancer 2 жыл бұрын
its true, i used a split lock washer on the race head on the rear hub drive side of my bicycle. Over weeks of riding the rear wheel play loosened until riding it felt like a massage machine on my arse and the tire would randomly brush the frame tail struts on both sides randomly and the axle bent because of the instability. Then i went and did it propper with lock nuts which are serrated just like these washers
@robertmceuen3630
@robertmceuen3630 Жыл бұрын
The contractor I worked for when building the LA Rams/ Chargers football stadium used this type lock washer. There were applications where it was critical that fasteners remained tightened to proper torque for a lifetime. Such as retractable roof sections weighing many tons.
@anteneupitra
@anteneupitra Жыл бұрын
I make my lock washers and none inlocked in my life..one day i ahd to lock a direction,, if it loose we could kill all of us, and used a method that will work for life, its my secret, it will not get out of there never.i call it counter tight, the more one unlock the more you lock the other so,, impossible mechanical unlock.. :) ancient machinist
@georgebuchanan3255
@georgebuchanan3255 Жыл бұрын
Going to use them on my Hot Rod, I get them from Mcmaster Carr with a zinc flake coating.
@dreadknot2238
@dreadknot2238 4 жыл бұрын
the state of the art design is 100% fantastic it work effective as advertised i got them on exhaust bolts
@Q60rs
@Q60rs Жыл бұрын
What kind of set up? 2 pair for each bolt? One on each side of gasket?
@parkers7009
@parkers7009 2 ай бұрын
This is an awesome invention. Can’t wait to try these out
@albinjamtinger6939
@albinjamtinger6939 Жыл бұрын
Cool video i work at the factory in Mattmar Sweden
@taylorlan3754
@taylorlan3754 18 күн бұрын
Do you technically need the lockers on either side of the hole? Or could you get by with the lower side one if you had to
@olenaerhardt7725
@olenaerhardt7725 3 жыл бұрын
I'm thinking to use Nord-lock washers for a project of new Ball Joints for a car 2003 Chevrolet Cavalier. Original Ball Joints were attached with rivets, which I removed following the instructions from Haynes Manual for that car. The new Ball Joints came with bolts and Prevailing Torque Nuts for attaching them to the Control Arm, but there was no instruction sheet for the torque specs for those nuts. I started to do a research on that question, contacted the seller and so forth, but meanwhile came across this new product, which seems very appealing to me due to its high reliability. May I know your opinion on the torque specifications if I use these washers and Prevailing Torque Nuts or even more interesting situation if to use Nord-lock washers and Nylon Nuts? As far as I understand you apply very small torques on those Nylon Nuts (about 10-14 Ft-lbs) due to their specific locking mechanism with that nylon inside of the nut. But the wedged washers require about 60-70 Ft-lbs (the bolts are M12-1.25, Class 10.9). I wrote to Nord-lock about your great film. Very informative film, thank you.
@cephasgunn1993
@cephasgunn1993 2 жыл бұрын
Finally the comment or info Ive been looking for, thank you. I'm currently rebuilding my rear suspension on a vw passat 02, and well the bolts are discontinued as they'd rather you buy the new one. I don't like new cars so i bought a junker to restore. the rear subframe i have is brand new with all attachments and bolts being upgraded to grade 10.9 and 12.9 where i can find them. the issue is the locating bolt and my fear of it coming apart when i am driving. tons of videos and forums later I see this comment. thank you you and this video have solidified my choice on these washers. I will also use Aerotight locking nuts. I need fail-proof, my Mum will be in the passenger seat at times.
@olenaerhardt7725
@olenaerhardt7725 Жыл бұрын
@@cephasgunn1993 The Nord-lock washers are doing a great job till now. I'm glad I installed them on that project w/new removable Ball-Joints. I don't know if it makes much sense, bcs I've read that the Control Arms wear as well, maybe that is why rivets were there, but for right now it works well, no nasty worn ball joints there anymore. I bought new spare Control Arms as well for the future though. But I'm afraid it will be much more difficult to replace them.
@christopherroncone6939
@christopherroncone6939 Жыл бұрын
I wonder how good will they work on sway bar links?
@erikyoung256
@erikyoung256 2 жыл бұрын
I used these lock washers on centrifugal machinery and they are second to none.!
@BasementEngineer
@BasementEngineer Ай бұрын
Kindly explain why these "miracle" washers are not required on cylinder head bolts, wheel lug nuts, and structural bolted joints of bridges and buildings. Perhaps the engineers that design these types of bolted joints know a thing or two about bolted joints???
@glockster6848
@glockster6848 Жыл бұрын
can it be use on a direct mount suppressor? crush washer has an uneven tension that can cause baffle strike
@tracktt1179
@tracktt1179 2 жыл бұрын
What would happen using them on exhaust & turbo studs that I guess could get to see 500+ degrees on track
@matsinkal
@matsinkal 2 жыл бұрын
They work great on turbo manifolds
3 жыл бұрын
Interessante. Vivendo e aprendendo.
@josephbeltramini5442
@josephbeltramini5442 3 жыл бұрын
Can you use this washer on the nut side? Will it have the same effect?
@lukamadunic8534
@lukamadunic8534 3 жыл бұрын
Yes! If you watched closely in video he used it in bolt and nut side.
@rapaent
@rapaent 3 жыл бұрын
How about "just" the nut side?
@alvarooryan3084
@alvarooryan3084 3 жыл бұрын
@@rapaent if it's through hole, you should use one pair under the bolt head and another pair under the nut.
@robshort1962
@robshort1962 2 жыл бұрын
If a single set is adequate under a bolt in a blind hole then a single set should work under a nut with a plain washer under the bolt. I've been using them for years like this.
@alvarooryan3084
@alvarooryan3084 2 жыл бұрын
@@robshort1962 the manufacturer recommends tu use one pair under the Bolt head and one pair under the nut, and not use the plain washer, the Nord-Lock washer needs to sit direct on the surface
@kingice3901
@kingice3901 Жыл бұрын
@StephenCox I have a 2006 Pontiac Torrent AWD and ever since I changed my tension pulley the bolt is constantly coming out , Will the Nord-Lock washer keep the bolt from coming out and which one do I need to use ?
@DiyEcoProjects
@DiyEcoProjects 3 жыл бұрын
Thank you for your video
@tomallen6073
@tomallen6073 Жыл бұрын
Cost vs performance loctite.
@aodhmacraynall8932
@aodhmacraynall8932 Жыл бұрын
Insructions real mechanics don't read instructions they don't use punctuation either
@m3chanist
@m3chanist 4 ай бұрын
"don't" they ?
@Xerock
@Xerock 4 жыл бұрын
Thank you very much for this video. I've always been confused by lock nut washers were supposed to work.
@anteneupitra
@anteneupitra Жыл бұрын
any lock washer works,, you dont need to buy the "special" product.
@hootinouts
@hootinouts Жыл бұрын
I specified Nord-Lock washers to be used with the fasteners to install custom intake and exhaust transition ducting I designed after the OE turbo chargers were upgraded on a huge marine diesel engine. I was concerned about the fasteners loosening due to vibration and thermal cycling and chose the Nord-Lock. Spring lock washers are a joke. I watched a video of them failing in a vibration test. Stop nuts are fine except the locking elements can only handle so much heat and certain application require they not be reused if removed. The other methods of locking such as lock wire or castellated nuts with cotter pins are a PITA and time consuming.
@kingice3901
@kingice3901 Жыл бұрын
@hootinouts I have a 2006 Pontiac Torrent AWD ever since I had to change my tension pulley the bolt keeps unscrewing itself, Do you know what size bolt goes through the tension pulley on my car so I can get the correct size Nord lock lock washer ?
@sudorights
@sudorights Жыл бұрын
Great video
@colecollins3530
@colecollins3530 3 жыл бұрын
I have a mobile repair and service company in Oregon that I just started but I have been a mechanic for 45 years. A rock driller for a rock quarry I worked on had them on every bolt and nut on the whole machine and I was really impressed once they lock they aren't moving . I am glad you made this video because now I know where to find them. Thanks
@josephpadula2283
@josephpadula2283 Жыл бұрын
These and lock tight are the only things that work. Go on any modern car and look for classical split lock washers , the car companies know they don’t work. If you think this is New NASA write a report on this in the 1990’s!
@ceciljones8890
@ceciljones8890 2 жыл бұрын
I am using these on the Airmaster 3 Blade Propeller on the aircraft I am building. Appear to work great (avoid having to safety wire the prop bolts) , but Airmaster says you can only reuse these once? The install manual says "The Nord-Lock® washers may only reused once. If reusing the washers, separate the washer pairs, and lubricate the cam surfaces with a film of grease before re-assembly."
@cebuanostud
@cebuanostud 9 ай бұрын
Too bad they aren't sold at big box stores.
@michaelguthrie2344
@michaelguthrie2344 2 жыл бұрын
This could be the answer to Sailboat Clevis pin replacement. I will use between 2 nuts on M3 Alan head bolts.
@chriskahlson
@chriskahlson 3 жыл бұрын
Dodge Ram Cummins PTO cover bolts on 5.9 24 valve
@aodhmacraynall8932
@aodhmacraynall8932 Жыл бұрын
darn good video. Im going to see if they have a kit or a selection.
@joshuachamberlain4279
@joshuachamberlain4279 3 жыл бұрын
how would these stand up with heat? say if i planned on using a couple of these to hold a bolt (on a clutch) locked inside a gearbox with grease that was reaching temps of 100 degrees ?
@alvarooryan3084
@alvarooryan3084 3 жыл бұрын
Their temperature range is -50°C to 200°C, so you shouldn't have problems. www.nord-lock.com/en-us/nord-lock/products/washers/selection-guide/
@fearlyenrage
@fearlyenrage Жыл бұрын
they work on a mechanical princip. Until the steel softens up they stay in the range of relaiable. When the steel softens the workload that holds the washers in place changes what in results in failure.
@globalchaos1984
@globalchaos1984 3 жыл бұрын
You look like the actor in the Thing movie remakes brother!
@cranebeg
@cranebeg 3 жыл бұрын
Joel Edgerton 👍
@wesleypelletier5087
@wesleypelletier5087 2 жыл бұрын
Where çan i get ?
@robinsmith8846
@robinsmith8846 2 жыл бұрын
Do they come in smaller household sizes? I have a firewand that hold a soapstone ball at end of metal rod. You light it on fire then put it in fireplace ..hold near kindling to start the fire. But the spin on it will overtime...unwind it and the nut falls into fireplace and then useless until replaced. :/ but they are no where near that size!
@zerker12312
@zerker12312 2 жыл бұрын
It's your lucky day; we make a lot of different dimensions, not just these big ones. / Employee
@zazzue5131
@zazzue5131 3 жыл бұрын
Sorry, Stephen, youtube decided to put an hour long commercial in the feed, part way through your video. I gave up. Too bad, the information looked good.
@robinsmith8846
@robinsmith8846 2 жыл бұрын
Skip advert button????
@mrcryptozoic817
@mrcryptozoic817 Жыл бұрын
I've seen that happen too. I don't recall seeing the expected "skip" button, instead had to just exit out of what I was watching.
@moa-wg3bo
@moa-wg3bo Жыл бұрын
adblock google chrome extension?? how can you not?
Nord-Lock Washers | Do they work better?
13:31
AvE
Рет қаралды 698 М.
Lock Washer & Lock Nut Vibration Test
5:21
Hacks by Dad
Рет қаралды 226 М.
An Unknown Ending💪
00:49
ISSEI / いっせい
Рет қаралды 55 МЛН
Brawl Stars Edit😈📕
00:15
Kan Andrey
Рет қаралды 55 МЛН
All About Washers - Types & Materials, USS vs SAE | Fasteners 101
20:49
Albany County Fasteners
Рет қаралды 67 М.
Candle Wax to Loosen Rusty Nuts a Myth or Hack?  Let's find out!
10:04
Project Farm
Рет қаралды 1,4 МЛН
this is the problem with threaded inserts
9:41
WoodcraftBySuman
Рет қаралды 422 М.
Thread locking | nut locking
10:45
Ultimate Handyman
Рет қаралды 169 М.
Sanding sucks...until you do THIS
10:23
Northern Works
Рет қаралды 321 М.
Simplest Way to Drill in the Center of ANY Rod!
4:00
JohnnyQ90
Рет қаралды 6 МЛН
100% J.B. Weld Cylinder Head?  Seriously!!
9:59
Project Farm
Рет қаралды 1,4 МЛН
What Would Happen If You Swiped The Waterjet?
10:17
Waterjet Channel
Рет қаралды 17 МЛН