Been waiting on this video,You have no idea how much info you've shared in this video 😅I'm was kinda scared to do my wiring but after this video I think i gain much confidence to start on my swap..thanks ma friend 💯❤️
@MillennialDad92 Жыл бұрын
Thanks for the support, glad I could help!
@yupitsmeagain8321 Жыл бұрын
I just found your channel and subscribed. I have an 02 GT I plan on swapping to a Coyote. I haven’t undertaken anything quite this extensive but it’ll be a good long term project. One step at a time! Love the content man keep it coming!
@MillennialDad928 ай бұрын
Thanks for the kind words. This was my first swap, ain’t nothing to it but to do it my friend.
@MarclenChin Жыл бұрын
This was incredibly informative, thank you so much for this!
@MillennialDad92 Жыл бұрын
No problem! I’m glad I could help
@TheRealSixShifty Жыл бұрын
Great video man. One correction tho. The yellow 12v wire with the white pair you tucked away did not need to be connected. It already was 12v hot from the coyote fuse box. It is a 12v power source for electric power steering and the white wires with it are signal wires to tighten steering with speed. Great video tho. No one has covered it this well until now
@seeunow446 ай бұрын
Awesome!! Appreciate your wisdom!!
@MillennialDad926 ай бұрын
No problem!
@jakehaynes431411 ай бұрын
So that yellow wire that you spliced into the radio? Is that the power wire to turn on the control pack and computer?
@MillennialDad928 ай бұрын
Apparently I wired it wrong, it’s a 12v source, doesn’t need connected it’s used to power electric power steering.
@lazy_4valve213 Жыл бұрын
I’m fighting an issue with the pcm not having communication. Where the car will just turn over but will not start. I checked grounds from the control pack and I did the motor mount to frame for the ground there. I am missing the extra ground wire that’s in the truck like you have. Do I need to have that? I’m kind of lost right now. Any help is appreciated.
@MillennialDad928 ай бұрын
Check your ignition relay trigger. If it doesn’t have a good connection it will cause a crank no start condition
@josebanderas207811 ай бұрын
Does the same gen2 harness work for a foxbody
@MillennialDad928 ай бұрын
Not sure what you mean. You can put a gen 2 engine and gen 2 harness in any vehicle on the planet
@edwardlanza7590 Жыл бұрын
How did you Connect your AC.? Can you touch on this…?
@MillennialDad92 Жыл бұрын
This is the 6th video about the swap. In part 3 I show installing the brackets that the compressor mounts to. Connects EXACTLY the same as when it had a 4.6. There’s literally no difference between before the Coyote and after. The pbh brackets make it where everything stays the same
@edwardlanza7590 Жыл бұрын
@@MillennialDad92 hopefully you can share some knowledge in the wiring.. I did my coyote swap but I’m stuck in the wiring. I used the original AC from 4.6 engine and I have the same PBH harness setup. Thank you.
@MillennialDad92 Жыл бұрын
@@edwardlanza7590 I showed the wiring in this video. There’s just one wire connector and it plugs in to the ac compressor. There’s no other wires involved with retaining the a/c. You use the original 4.6 engine harness and plug the ac up just like you did before the swap.