Mustang Big Brakes Front and Rear for less than $600! 1979-2004 (ATS Brembos Front, Taurus Rear)

Big Brakes Front and Rear for Mustangs for less than $600! (ATS Brembos Front, Taurus Rear) This Brembo/Taurus brake setup will bolt on a SN95 knuckle using adapters for S&S Engineering. The front calipers are brand new Brembo calipers for a Cadillac ATS. They are extremely cheap at about $120 per caliper. This setup uses a stock 13" 94-04 Cobra front rotor and will fit under 17 inch wheels. The rear uses a Taurus rear caliper in the stock mustang bracket. You can buy this setup for less than $600 and the brake bias ends up extremely close to stock. Lots of people are not upgrading the rear calipers and shift their brake bias too far forward potentially INCREASING stopping distance!
Parts:
ATS Brembo Caliper (Driver): amzn.to/3ad5m96
ATS Brembo Caliper (Passenger): amzn.to/38vsBuj
Pads I used: amzn.to/3GwECw8
Rotor:amzn.to/3NIbiFh
Braided Hoses W/banjo bolts: amzn.to/3a4Sqlp
Paint: amzn.to/3N3CI8D
Brembo Decals: amzn.to/3t2myok
Banjo Bolt: amzn.to/3lUoHhI
Rear:
43mm Taurus Caliper (driver): amzn.to/3NNPiJn
43mm Taurus Caliper (Passenger): amzn.to/3lX2JLe
11.65" Cobra Disc Upgrade: amzn.to/3oMbvNl
---------The Taurus caliper will bolt right into any 94-04 Mustang caliper bracket. The 11.65" Cobra rear disc provides the ideal brake bias but, you can bolt the Taurus caliper onto a stock 10 disc and bracket as well and receive a slight improvement in brake bias for the ATS fronts.
Send S&S an email for a quote on the adapters. They do everything though paypal. They are pretty responsive to messages and their product works great. No issues at all.
S&S Engineering: [e-mail]
S&S Engineering FB: / ssengineeringllc
My Amazon Store: www.amazon.com/shop/repairgeek
Help support the channel, buy using my Amazon links
As an Amazon Associate I earn from qualifying purchases and your cost is exactly the same.
I source all of my service data from the same place that professional shops do. You can as well: www.pntrac.com/t/SENKSUZKRktD...
Questions? Shoot me an email at [e-mail]
00:00 Intro
00:04 Parts that I'm using
1:59 How much is a normal "Big Brake Kit"?
2:43 Caliper Modification/S&S Bushing Installation
7:30 Final Assembly
8:19 Brake pad installation
9:56 Brake hose/banjo bolt information
10:42 Rear brake upgrade
13:18 What wheels can you use?
14:38 What's the difference between the Cobra R and ATS Calipers?
15:30 Total Cost for the ATS brakes
16:17 How does it stop?
18:52 Outro
#brembo #bigbrakes #mustang
Disclaimer:
The information, demonstration and any content contained in this video is for informational purposes only. The user Repair Geek makes no warranty, express or implied, regarding the effectiveness or safety of the contents of this video. In no way should the contents of the video, including the tools used, be repeated or tried by anyone. Viewers should only seek the help of a trained professional located at a licensed auto repair shop for any fix, modification, alteration, or any change to their vehicle. Repair Geek shall not be liable for any injury, damage, or loss to any person or property that may result from use of the tools, equipment, or any content contained in this video. In addition, there is no way to guarantee that the video is not altered or modified or is not in the final form submitted by Repair Geek and therefore, Repair Geek does not warrant that the video is unaltered or not modified. The links on this video to products are for informational purposes only and in no way are an endorsement of the safety or effectiveness of the particular product. Viewers understand that anything contained in this video or linked to or from this video is the sole responsibility of the viewer and in no way provides an express or implied warranty as to the safety or effectiveness of any linked tool, product, or video. Therefore, viewer agrees to release, waive, and discharge Repair Geek or anyone affiliated with Repair Geek, from any and all liability, claims, demands, actions, and causes of action whatsoever arising out of or related to any loss, damage, or injury, including death, that may be sustained by the viewer, or to any property belonging to viewer, regardless of whether the loss is linked to the use of the contents of this video, or otherwise and regardless of whether such liability arises in tort, contract, strict liability, or otherwise, to the fullest extent allowed by law.

[@RepairGeek]

Parts: ATS Brembo Caliper (Driver): amzn.to/3ad5m96 ATS Brembo Caliper (Passenger): amzn.to/38vsBuj Pads I used: amzn.to/3GwECw8 Rotor:amzn.to/3Rii1sO Braided Hoses W/banjo bolts 99-04: amzn.to/3a4Sqlp Braided Hoses W/banjo bolts 94-98: amzn.to/3JlFWp6 Paint: amzn.to/3N3CI8D Brembo Decals: amzn.to/3t2myok Banjo Bolt: amzn.to/3lUoHhI Rear: 43mm Taurus Caliper (driver): amzn.to/3NNPiJn 43mm Taurus Caliper (Passenger): amzn.to/3lX2JLe 11.65" Cobra Disc Upgrade: amzn.to/3oMbvNl ---------The Taurus caliper will bolt right into any 94-04 Mustang caliper bracket. The 11.65" Cobra rear disc provides the ideal brake bias but, you can bolt the Taurus caliper onto a stock 10 disc and bracket as well and receive a slight improvement in brake bias for the ATS fronts. Send S&S an email for a quote on the adapters. They do everything though paypal. They are pretty responsive to messages and their product works great. No issues at all. S&S Engineering: [e-mail] S&S Engineering FB: facebook.com/SSEngineerin... My Amazon Store: www.amazon.com/shop/repairgeek Help support the channel, buy using my Amazon links As an Amazon Associate I earn from qualifying purchases and your cost is exactly the same.

[@luisvaldez6204]

1998 Mustang GT . I bought the Taurus calipers.. I want to install the cobra rear rotors...(Bigger). Do I need the cobra brackets as well? will the cobra rotor fit inside the Taurus calipers.. and will the Taurus calipers be a straight bolt on the cobra brackets if needed?

[@1tufgt]

@@luisvaldez6204 yes you do since they are wider to accommodate the bigger vented rear rotors.

[@ardo8420]

Whats the link for those rotors

[@talksondblock9483]

Will this setup fit with 19x8.5

[@tyjaebowie933]

Man this video was so perfectly done everything was so clearly presented

[@TaylorTobitt]

this was super helpful. i was gonna spend about 1,400 on a big brake kit but this seems to be a way better option for me with limited track time. thank you for this video!!

[@wardfrahler6779]

I’ve watched a few others on this swap after watching yours. You do a great job explaining everything. Thank you for the help.

[@thanhbeach814]

I'm gonna put this kit on my supra. Thank you for the crisp and clean video

[@mustafahasan264]

Bro made this video so simple and easy to understand. Thank you so much.

[@chriszawacki4092]

Great info and glad you mentioned the Taurus calipers

[@antiricergt]

Haven’t seen you before on KZbin but after watching this video I’m subscribing. I liked how you explained everything and went into detail and added the part numbers with list of everything needed. I have a 86 Foxbody with these ATS calipers. 306 Turbo, aluminum heads and on and on Also have a 01 Cobra but currently working on the Fox. Cobra has been sitting I’ll probably sale it I don’t drive it but anyways good video bud.

[@beerwrenchgarage]

Excellent stuff - thanks for the heads up on the S&S kit. I sourced my ATS calipers from marketplace for $200 and I pulled a set of '43' rear calipers from a Taurus at the local yard for less than $40. Looking forward to seeing how this works on my 2004 GT.

[@myeighty-nine7813]

Dude such great info, thanks for this video I had got the Brembo kit a month ago but couldn't figure out the rear brakes or the wheel options

[@keithgosselin6481]

I subscribed because of the job you did with this viddy. FANTASTIC!!!

[@Lostautofilm]

This video was super detailed and helpful. Looking to give this a try in the future!

[@2wheelcobra]

I'm really enjoying your videos. Your car seems to be getting setup very similar to mine, with like goals. Although, I am not nearly as far along as you. Stock 94 GT 5-speed convertible, "budget grand tourer". Just welded in the stiffler's fit system last night, and picked up BOSS 302 Brembos for $120 locally. Bought a slightly used set of high performance summer tires too. 14in rotors on the way, along with solid steering rack bushings. Eibach front and rear swaybars showed up yesterday too. I share this car with my parents ( both 60 years old) and live in WV, surrounded by great driving roads. I have to walk a fine line between making performance modifications...and not doing anything to upset my wife and my parents experience. lol Your car seems to be setup in a way that would be the solution for what I'm looking for....while keeping it pleasant for them as well.

[@RichPedro]

This popped up in my feed, now I'm tempted to do this to my foxbody instead of the 03 Cobra brake upgrade.

[@hyslopboys9600]

AWESOME video! Never knew this kinda thing existed! Wish I could adapt this to an svt lightning though!

[@jonathanestrada576]

Great video!!!! Every informative and to the point. Just subscribe.

[@fishsquishguy1833]

Really well done video! Thanks for explaining why the need for Taurus rears and giving all the piston diameters. Very comprehensive and very much appreciated! I’m looking into piecing this together right now and previously had my eyes on the Ford Racing kit. I’m running 18” AFS Mach 1 wheel on my 03 and would very much like to keep them so hopefully they give me enough clearance over the stock 17”? Worst case I’m using a wheel spacer and ARP studs I guess?

[@RepairGeek]

Mach 1 wheel is going to need a spacer.

[@thomaseld1090]

Genius thanks bud!

[@steviefresh4602]

Thank you bro!! Amazing breakdown video! Think this is def the direction Im gonna go with my sn95 now. One thing I'm thinking, and will have to do a little research on, you mentioned softer pedal feel, gotta be a master cylinder upgrade out there that would probably help with that🤔

[@RepairGeek]

Not for a 96+ hydroboost car. The stock 96+ master is 1 1/16th. Some of the older superduty stuff had a 1 1/8 but they used a different mounting flange for the master and a larger booster that doesn't fit.

[@sschu2223]

Thanks for the info .you got a new subscriber

[@salvadorrobledo1151]

You convinced me to do this to my 00 Mustang

[@Dave-bz4pb]

Same

[@Quik5oh]

Super helpful video (like all of your videos), thanks for the details and tips to ensure that this particular upgrade produces the best possible results! Is it possible to adjust the rear braking bias (if using the 38mm rear GT/COBRA calipers) back to 30% using an adjustable proportioning valve (passenger side firewall unit) when upgrading to the ATS Brembo calipers in a Fox chassis 79-93 application? Does the 43mm Taurus rear caliper upgrade apply to 94+ Mustangs or 99+ Mustangs only or all Mustangs from 79-04? Surprising that no one else talks about the brake bias change with the larger pistons in the ATS Brembo calipers. I purchased the S&S engineering adapters, great folks to work with! I'll have some actual track testing/experience that I can share once I get the setup installed in my '88 LX 5.0 and on the track next summer. I'm currently running the 13" "COBRA" rotors with MACH 1 calipers (same as the COBRA calipers), '93 COBRA booster, and 1" 93 COBRA master cylinder. Looking forward to trying out the change on the track. May try Hawk HPS pads instead of the ceramic pads though or may try out both since they are so easy to change with this setup.

[@BlueOvalEdge]

Well done. I recommend this upgrade not just for the increased braking performance, but to eliminate the front PBR Cobra caliper which has a very poor brake pad anti-rattle design. Only the bottom of the pads use an anti-rattle clip, while the top of the pad has no clip but rather the pad just rides in the caliper bracket slot. Brake grease in those slots and plenty of tension on the lower anti-rattle clips (LRS-2296A) will keep the pads from rattling for about 6 months, then, you will need to regrease and bend out the anti-rattle clips to maintain tension on the pads and keep them from rattling. I have had front and rear Cobra brakes (rear M-2330-M) on my daily driver 2001 Mustang GT for 10 years, so trust me on this one. I will say that braking performance with front and rear Cobra brakes on a new edge GT is exceptional for a daily driver, however the front caliper pad rattling will drive you nuts, especially if you own a convertible, which I do. Also of note and in favor of this Brembo upgrade is the fact that the 2003-2004 Cobra and Mach I calipers are really for 12” rotors which is why so much rotor is not touched by the pad on a Cobra 13.1” rotor. If any Ford owners know how to permanently get the rattling out of the stock PBR calipers, please let me know or I am going to perform this mod for my daily driver just to eliminate the PBR death rattle.

[@RepairGeek]

Never had an issue with my PBR's rattling. Your retaining pins are installed at the rear of the caliper correct?

[@BlueOvalEdge]

@@RepairGeek Yes, the pins are installed on the rear (bottom) of the pads where the clips are. Its not possible to install them on the front (top) of the pads by mistake and although there is a hole in the pad, its not for the pin. The pin would not fit through the hole and the rotor is right behind the pin anyway. Really not sure what the hole is in the top of the pad. As you know, the pin passes through a radius on the bottom of the pad mated to a similar radius on the caliper bracket. I wonder if its possible that the caliper mounting bracket is slightly worn out at the top (where there are no clips) allowing the pad to clang around in the slot? I have even tried stock Cobra motorcraft pads and they rattled around too. Very annoying. Anyway, thanks for thinking about it. No need to dwell on it. One day I will get pissed off at the rattling every 6 months and perform your upgrade. Congrats on the nuptials.

[@RepairGeek]

If the brackets and pads get flipped driver to passenger and vice versa you can install them with the pins on the top. That will cause pad knock when you apply the brakes and the pad slams forward against the pin. I've done it haha. So far I have no regrets with the ATS setup. Thanks for watching!

[@davidhawkins5350]

Great video and how to save money without paying that Brembo price if you were to order it exactly for that car , 👍, You didn't mention it but that set up will definitely stay cooler under heavy breaking & less brake fade , I recently did a drum to disc conversion on my 1994 F350 and it also used a Cadillac caliper, Idk if Brembo was making the calipers or not ,So if anyone is doing that conversion look up( Graveyard Broncos ) for the complete kit & save money, Some welding needed for the brakets to the axle tube.

[@jplperformance9073]

Hell of a video

[@spiridondimaris465]

Yeah well done geek good job

[@601GooRue]

Looks good man. what size rim you use on the front? what offset clears the Caliper?

[@riverview2233]

Great video! I am adding this setup to my '85 GT and Cobra rear disc for strictly endurance racing use. Since Repair Geek indicates the bias is similar to stock, does anyone know whether the stock brake distribution block on the '85 Mustang will work ok with this upgraded brake setup? I recognize that I will need to install a '87-93 GT booster and a 1 1/16" MC.

[@TheClapGodSr.]

Hi, just wanted to make sure, so the rotor listed in the description will fit in the front with the ats calipers correct? I am looking into doing this and want to make sure it will fit. Also, maybe stupid question but do you need brake pads for the tarus calipers in the rear?

[@phillipstein9099]

Rear Cobra brakes use a 11.65in. and are vented which is worth the cost of that upgrade. That said with the stock brakes with the Taurus caliper upgrade I'd still gut the stock proportioning valve with the kit from Maximum Motorsports and add an adjustable proportioning valve. Wilwood has a valve that bolts right in place of the union in the line on the right side of the engine compartment on the firewall.

[@neilsvidz9577]

I think you need to upgrade your master cylinder to improve your pedal feel. I know the fox cobra upgrade kit came with booster and master to correct for the upgraded brakes front and back. I started with the original cobra upgrade on my fox station wagon, now I've upgraded to the cobra r brembos and the taurus calipers will be the final piece. If it turns out that the ats brakes provide significantly more stopping power then I may try them. The internal crossover may be a concern because the force used to clamp the rotor is also trying to separate the two caliper halves. Great video. Nice job!

[@RepairGeek]

There's no upgraded masters for a hydro boost car. It already has a 1 1/16th.

[@chrisfrank8413]

Fan Freakin 'A' Tastic! Great! Thanks.

[@danflowers6845]

Super video...

[@chrisvela5462]

Have mine off in powdercoating and found out Powerstop sells the Taurus calipers powdercoated!

[@nimrodpaul6875]

I want to upgrade my 06 mustang brakes ( rotors/calipers/pads) I would so appreciate any recommendation! You know your stuff brother. I was looking at the z23 but not real impressed unless you think differently?

[@Chris-zm7wh]

Great channel super helpful are your fr500s 17s??

[@RepairGeek]

18"

[@dewholdingsllc1050]

Nice content. Is there a steering knuckle upgrade to use with that 4 piston caliper for classic full size ford cars. What is the bolt pattern?

[@angry408w7]

could i use the 43mm rear caliper with the Lincoln 73mm front caliper? 5 lug conversion no sn95 spindles. but using 93 cobra booster and and matching mc.

[@TheJhine5588]

Did this make the brake pedal any deeper, as in you have to push the pedal down further than before the upgrade? Increasing slave piston area will require more fluid. Did you replace he master with a larger one?

[@limpy654]

Wouldn’t you be able to use a proportioning valve to fix the bias?

[@jackattack2339]

Love it did it , I noticed a softer brake pedal , which I figured would be the case with more pistons up front . Would it be wise to upgrade brake booster ? Or just run it ?

[@RepairGeek]

Is the system fully bled? What master do you have? My car as more travel in the pedal but once it bites the pedal is very firm.

[@salvadorrobledo1151]

Is it worth going with the 11.65" rear rotors or do the stock GT ones make full contact when you have the Tauros caliper?

[@MMMX38]

I'm not sure if you've seen, but Lincoln Mark VII rear brakes are absolutely huge as well. That might be another cheap rear brake upgrade.

[@timweb1510]

Have you ever seen these brakes on the front with 17” racestars? The small 4” ones, thanks. I searched online a few times with no results

[@StoneyBrownTV]

I'm curious would this work for a 6th gen Ford Taurus for front brakes? This would help a lot on my 2013

[@TPMach1]

Hey man with those setup did you have to use that rotor only or could you use a different one? I bought the EBC rotors for my setup like this but I haven’t put them in yet. I’ve just still been doing a lot of research to make sure they fit first. I have a ‘03 Mach1 and they’re made for that car. I want to be safe than sorry lol

[@RepairGeek]

You can use ANY 13" rotor from a 94-04 car.

[@chuckp7970]

Hello, I've ordered the parts for the front, but do you know what is needed to be able to mount to the Taurus rear calipers onto a Foxbody (91) rear end? Great video, thanks for making it!

[@RepairGeek]

You will need to order whatever it takes to put a 11.5 SN95 rear rotor and caliper on a fox.

[@BlueOvalEdge]

Forgot to ask what thickness the rotor spacer is? Thanks for the informative video.

[@RepairGeek]

I don't remember to be honest. It's like 1-3mm or so.

[@dntlss]

My god that make your mustang slower with GM parts was priceless 😂😂

[@2broke4bags]

Question does those brake lines require bubble flare? Or inverted ?

[@Morax515]

Would the ATS brembo’s clear 17x9 wheels? I have the oem Tri-bars on my 95 GT but I’ll be switching them over for Cobra R wheels soon. Regardless both would be 17x9

[@stephendwinells8260]

What about using stock cobra rear calipers?

[@vrm86gt]

sub'd good info! Thanks!

[@ccmotorsportsflatironracin5838]

do you have a link to the 2 piece rotors? thx great video. read upgrade I have not seen anyone talk about.

[@RepairGeek]

The rotors I purchased on Ebay about 8 months prior. I got the set for about $250 NOS from 2005. To buy them new now is $475 per rotor was the cheapest I saw. They aren't worth 475 each. They are DBA 5000 series rotors. If you google: DBA 5000 Mustang Cobra. They pop right up. Unless you get a smoking deal. Just buy regular rotors.

[@jeffscales9817]

Will these work on a 1967 Camaro I want to do a brake upgrade not sure which route to take

[@mvpolo64]

How’s the brake pedal feel and initial bite? Does it make a huge difference or just marginal/compromise besides getting the willwood or bear breaks? I’d rather by once cry once hahaha 😭

[@RepairGeek]

It had enough brake power to compelety overwhelm a set of 275 Nitto 555's in a panic stop. I've since upgraded to Michelin PS4S's they have much more grip than the nittos.

[@5point4LSX]

With the Rear Taurus Calipers, do you need to install the 11.65 rotor conversion bracket still, or can you put these calipers on with a cobra rear rotor? I am not wanting to pull the rear axles out....again.

[@doriscardenas27]

I install cobra rear calipers on my fox body mustang a Taurus calipers are bigger

[@asoljz1779]

I wonder if this would also work on a crown victoria

[@SweetLouieolive]

I'm in the middle of this upgrade (amazing video!) and am currently wheel shopping. Anyone have any idea of the offset that will fit these?

[@stevensheldon9271]

How can I measure my existing rims to know if they will work with this upgrade or not?

[@edwoods6110]

I have a 94 convertible will I need to update the master cylinder?

[@m1kefloyd]

will stock GT brake hoses work with these calipers ?

[@m.c.9991]

What is the thickness of tne spacer, and can i use washers as spacers?

[@tnev22]

Struggling to find these rotors. Do you have a part number for the set you installed? Link in the description brings me to a different set on Amazon. Appreciate all the details in your content. Thank you.

[@RepairGeek]

They aren't worth the coin. This price is for 1 rotor.. I paid $250 for the pair. Here's a link:www.cspracing.com/dba-dba5069gldxs-94-04-mustang-cobra-bullitt-mach1-front-drilled-slotted-5000-series-2-piece-rotor-assembled-w/dba5069gldxs/

[@tnev22]

@@RepairGeek appreciate the link and the honesty. Thank you.

[@6lik6]

i wonder if this will work on a 08 crown vic…could be nice

[@Blackevilmisanthrope]

That whole rear rotor has paint on it!

[@RepairGeek]

And the first time you apply the brakes it comes right off.

[@caesar8624]

I would like 15 inch calipers, do you think that would be possible?

[@willdee513]

so is there a rotor I can use if i need to use the stock gt sized rotors . Id love to go to a vented rotor, but I cant fit that behind my rear drag wheel?

[@dennis17116]

Technically all you have to do is drill out the spindle to a 14.3mm opening and it all bolts up without the kit. You will have to either machine the contact area to spindle 2mm or space the rotor out 2mm for perfect Fitment.

[@RepairGeek]

You can. It also turns a $200 spindle into a paper weight unless you run this caliper. Also, these bushings drop the caliper down onto the rotor further as well. Again you could accomplish the same thing slotting out the holes correctly but you really don't want a brake caliper bolting into a slotted hole.

[@EivinSukoi]

Excúseme not everyone has a metal Lathe machine 😂

[@ElMachChingon]

I contacted Russell for braided brake lines and I’m confused. Their first email response to me merely said to check their catalog and answered none of my questions. I followed up earlier today stating that they do not have a listing for 03/04 Mach 1s and asked if there was a part number not shown in their catalog. I also asked if their lines would fit/work with ATS calipers….they said I’ll have to build my own set! 😫 I have an 03 Mach with traction control, would the part number you used work for me?

[@azarellediaz4892]

I installed a 5.0L on my vehicle, I’m looking at upgrading my brakes any idea if this will fit an ‘08 Ranger?

[@24theMoney]

How well do these calipers work with stock foxbody 87-93 brake booster?

[@Psy8ern3t1k]

I have a '00 v6 new edge I'm building as a drift car. I was wondering if you might know whether or not the taurus rear calipers would work with the dual caliper brackets for a drift set-up? I assume the dual caliper bracket is meant for the stock GT brake calipers, and I plan on upgrading the brakes all around when I go to dual caliper, but until I saw this video I was gonna go with GT brakes. But if the Taurus rear calipers will also work, then I'll go with them and the ATS fronts.

[@RepairGeek]

If the bracket is designed for a stock 94-04 mustang rear caliper, it will bolt right in.

[@stanmack1]

The brakes are the same on the v6 and GT.

[@phil2park2]

Will this work on a foxbody with a sn95 brake kit

[@chesspiece81]

Out of curiosity would it be possible to use this brake setup designed on a Mustang on a 2000 Ford Ranger with stock front and 8.8 Explorer disc brake rear end?

[@william-ezekielverduzco5163]

I would like to know if these would fit 11 wrx

[@EscortSportage]

I run the same brake setup

[@shawnward6916]

Did you upgrade the master cylinder, if so, what did you go with?

[@RepairGeek]

Stock 1 1/16th bore master on this car.

[@Jfonseca6]

Would this be an upgrade for ford explorer 8.8 brakes

[@xmoto7377]

Wait so we need the 11.5" rear cobra rotors with the Taurus calipers in the rear? Just want to double check before I pull the trigger on the rears. I already have the brembos up front and need to fix the variance

[@RepairGeek]

The taurus calipers will help the rear bias even on a 10 inch rotor. You dont need the 11.65 rotor to install the taurus caliper. It will bolt up fine. The 11.65 rear w/taurus calipers is virtually stock as far as bias using ATS fronts.

[@xmoto7377]

@@RepairGeek so I can bolt up the Taurus rear caliper and use either the 10" rotor or the 11.6"?

[@RepairGeek]

Not sure what you are working on but, yes using a 94-04 mustang caliper bracket yes, bolts right in.

[@Ywieb_]

Can’t i use 4 pistons brakes on rear wheel?

[@racequad9]

Great informative video. Do you have link to the rear SS brake lines?

[@RepairGeek]

Rears are kind of a pain. ABS vs NON-ABS takes a different rear hose. IRS is also a different hose. These are the lines I have for my 01 Solid axle ABS car:amzn.to/3pQdUa9

[@racequad9]

@@RepairGeek Yeah i gotta find a set for an ABS IRS 03 cobra. Crazy how much more expensive the rear SS brake lines are compared to the front smh

[@RepairGeek]

IRS Kit:amzn.to/3CtFPEr

[@racequad9]

​@@RepairGeekI'll let my buddy know about the kit. He does already have new front SS brake lines but he can just sell those. Big thanks for your help.

[@robertwood3970]

Thinking about doing this swap with a 98 Ranger, what is the bolt center to bolt center measurement of the caliper bolt holes on the SN95 spindle?

[@RepairGeek]

You're going to have to dig around on a forum for that info. My car is assembled lol.

[@cobrajeff96]

Isn't going to provide much stopping power over the factory cobra setup. First, it's the same diameter rotor so leverage is not increased over stock. About the only two benefits you get are larger pad surface area (a meager increase in brake torque) and higher thermal capacity and more even pad wear with 4 pistons versus 2 from stock. If you really want a big stopper, get a kit with a 14" or even a 15" rotor, though different wheels are usually required for this.

[@RepairGeek]

Well, I'm using the entire face of the rotor, which cobra's didn't. The pistons are larger than any factory cobra (38mm or 40mm depending on the year). So this setup has more clamping power because of the 42mm pistons and also has better pedal feel at high braking forces because there is far less deflection in the caliper at high clamping loads. There are also 2 sides to thermal capacity. A larger rotor at 14 or 15" has more mass (weight) and would take longer to heat up but, nobody ever mentions that a larger rotor also takes longer to cool down. This car is nearly 1000 lbs lighter than a S550 GT500. You don't need a 15" rotor if the car isn't morbidly obese to start with...

[@stevenbayless210]

I hate to ask this as I'm sure you've heard it a lot but I have to be sure..... so if I go with the Taurus calipers, use the stock GT rotors, correct? I'm going to go slotted so I want to buy a new set but wanted to make sure before I bought them.

[@RepairGeek]

You CAN use the GT rears with the Taurus calipers. The cobra rear brackets and rotors are larger and are vented. This will help shift even more bias to the rear.

[@turbozisimracing3877]

Does this caliper and mod kit take the place of a caliper bracket? ..bolt directly to the spindle? Work with 96-04 spindle also?

[@RepairGeek]

Yes and yes.

[@DrPopola09]

do you need to do a 5 lug conversion?

[@chrisfrank8413]

I've been seing mention of a slightly larger rotor, 13.1 or .2 i think? Is there a Mustang/Cobra rotor that will center and face the full pad so there is no material on the outside creating a lip? And also you rotor link goes to a 14" rotor. Seems incorrect. Also, the Banjo bolts link looks nasty. No copper bushings and looks like cast garb. any link to a better banjo bolt? Can you use the stock Cobra brake hoses with a new Banjo?

[@RepairGeek]

I have a lip at the top probably around 1/8th of an inch on the pad. I've ran this setup on a 6000 mile cross country drive and a track day at the halfway point of that trip. This setup works great. As far as the rotor I have linked, that is a 94-04 13" rotor. The dimensions listed on the amazon page are for the size of the rotor's box, not the rotor itself. Banjo bolt information: 9:56

[@thehellfox3423]

94-2004 cobras also have the same rear caliper as the Taurus,

[@RepairGeek]

No they don't. Check the piston sizes.

[@cme3172]

Where can i get the front caliber inserts from to bolt to the spindle

[@kraagnjilwulf1413]

What size are the rotors? I want sport rotors, but you linked OE style smooth rotors and they don't list the size.

[@RepairGeek]

13"

[@devincrawford1646]

Why not use the ats rear brembo also?

[@ff23018]

If I install these brembos on 2003 mustang gt and add the taurus 43mm rear calipers without changing out the rotors to the bigger ones will the bias be off by alot. Is it still in an acceptable range to cause the car to brake evenly or is it a must to get to bigger rotor as well?????

[@ff23018]

also where did you find the chart that explains all the brake kit bias?

[@cesarsgarage1393]

I’ve had this set up on my car for years now, you can use 11-14 none Brembo mustang rotors which are bigger then the cobra 13” rotors to have more pad contact on rotor (Cobra rotors are smaller causing some of the brake pad to not ware evenly) and avoid having to use the spacer s&s requires on the inside of the rotor for 13” cobra rotors

[@beanermonkey]

How much did it cost and where can I get the parts. Want to get brakes but 1500 is to steep for me

[@ChaseBond11]

Thanks, Caesar! You saved me even more time and money. Knowledge is power.

[@ben_rowe]

would sve series 1 wheels clear the breaks?

[@JustChuck]

Great video, I have the same S&S kit and will be installing next weekend. On a side note, I went with the 13.25 rotors from a 2010-2014 GT, S&S has a different rotor spacer for those rotors. So from what I can tell , the rear calipers are for a Taurus 93-99 in the event you want to purchase from your local parts store. I already have the 04 GT brakes, it sounds like I can still use the '04 GT rotors and that will be my phase 1. Which brackets would I need for the Cobra rotors? Would I need '04 Cobra rotors.

[@RepairGeek]

You need the axle brackets from a cobra. Ford Racing still sells the kit to do this that comes with axle brackets and the rotors but, I purchased my kit in 2016 for about $200 from Summit. Part number M2300M . That same kit is over $400 now. Even with the Ford kit you will need to supply your own 94-04 Cobra caliper bracket.

[@glenndiorio8967]

@@RepairGeek Did I hear you right saying you can use stock pads in the rear? A Cobra caliper uses thinner pads than a stock setup due to wider rotors. At least from what I've seen. So going from a GT to Cobra rotor you need Cobra pads...correct?

[@RepairGeek]

@@glenndiorio8967 A GT and a cobra use the same pad shape. The fiction material is slightly thinner on a Cobra pad. Problem is a lot of these aftermarket pad manufacturers just have 1 part number for both cars. Some fit great others need the pad material ground down to fit the cobra rotor.

[@mikecam94]

So just to clarify, if I were to use the ATS calipers in tandem with the Taurus calipers, and a 1 1/16 master cylinder, I would NOT have to use an adjustable prop valve as i would retain the “stock” bias with the Taurus calipers ? Or would I still need an adjustable prop valve? Have a foxbody btw but considering this setup

[@RepairGeek]

Considering those were rear drum originally I'm not sure to be perfectly honest with you. If it was me I would bolt this setup on, drive it a litte and see how it behaves. If the rears lock before the fronts install the proportioning valve. You will need the 1 1/16" master for sure.

[@mikecam94]

@@RepairGeek yeah I ordered a stock 87-93 booster to pair with a 94-95 gt master. Since I have a 1980, I can’t fit any booster bigger than the stock gt without beating the hell out of my strut tower which I refuse to do. 😂

[@mikecam94]

@@RepairGeek can I get your instagram in case I have any other questions ?

[@RepairGeek]

@@mikecam94 [e-mail] it may take me a day or 2 but I'll get back to you.

[@talksondblock9483]

Is all the brake lines stocks lines

[@steamy1225]

I like what you showed me. But i have a fox chassis Mustang , will this work on that car? i did upgrade the rear brakes from drum to disc with stock Mustang components but still have stock front brakes. 11 inch sloted rotors with ceramic pads but the original calipers. also converted to 5 lug. Also what year Taurus are these rear calipers from. The Amzon links don't mention the year. And i agree , your stopping power is only as good as the tires grip to the road.

[@RepairGeek]

Use a SN95 spindle on the Fox lower control arm. The rest should be pretty much the same. Also you may have to up size your master cylinder. This car is using a 1-1/16th bore MC (factory). The foxes I believe are 1 inch bore or less. You might run out of pedal travel before the brakes lock up. A MC from a 94-95 cobra should bolt in and be the correct size I believe.

[@myeighty-nine7813]

I'm doing this on my 89 GT we need to get the 93 cobra brake booster and a 93 cobra master cylinder

[@steamy1225]

@@RepairGeek Sorry for the late reply. I do have a 94 Cobra MC on the car already since i converted the rears to disc Back in 2006. I need to get the SN95 spindles. My original calipers oar grinding on the rotor for some reason and i think the SN 95 would be better. Do you know ere i can get some SN 95 spindles.? Thanks. I also have the 17 " wheels , factory for 94-85 Stang GT spot package. Double 3 spoke. Love them.

[@steamy1225]

@@myeighty-nine7813 Thanks. I already have the 94 Cobra Master on as i did a rear disc conversion on the car and a booster from a v6 car. much bigger.