Modification of old and damage Hydraulic Jack 10tons and 32tons capacity

I use this modification to my next project,which is I make a manual hydrualic bending machine.

[@jdw7092]

👍👍👍...use a small jack as a stag and accumulate, then use a small jake pump to compress hydraulic oil and send it to the large jack. (It's a really great way of thinking..it's the same principle as Hydraulic pump system from the master pump of a large truck..) Details that the creator of the clip should emphasize to the audience are: The ball bearings of the non-return valve Must be very good at the bearing because when lifting a lot of weight The pressure will be greater. Must not miss it, it is dangerous. can cause disability..(thanks for clip)..👍👍👍💖💖💖

[@roberthooper8883]

Not questioning him because I can see that it works- but why didn't he just drill thru the red jack top cylinder, thread that part, install pipe fitting, then weld red jack cylinder to red jack outer cylinder? Would have done the same thing with far less work.

[@Creativevillageidea-s3f]

Mantap sekali idenya mas bro... Sehat terus dan terus berkarya.. 👍👍👏👏🙏🙏

[@aubrymacielpereirafilho3017]

É interessante com esse sistema acredito que potencializou a força do segundo macaco!(Jack) Valeu muito obrigado!

[@hienrmah]

Quá trinh sáng tạo hay quá bạn ơi🎉🎉🎉

[@josephcooksley3219]

Good concept other the feed line through the machined edge of the Circumference of the base ... then the whole flat surface could of been used as a thrust plate ... 😮😮😮😮

[@tdotw77]

I thought that exactly too. Why not tap the side if you're gonna go through all this fab work? 🤦🏻‍♂️🤔😀🛠️🦺 ✊🏻🇺🇸🦅

[@doughenning4899]

I made a similar modification 30 years ago 👍

[@匚丹尺刀口ち口]

Legal, porém o lugar onde foi instalado a entrada da mangueira do segundo macaco cilindro ficou no lugar errado, deveria ser do lado e não embaixo.

[@MarceloSousa-z9m]

muito bacana esse projeto 👋👋👋

[@Jazellerhae]

Nice tito😊

[@creativejunior7060]

Hala, Pinoy din po pala si Idol Ang galing po nang tito nyo Idol ko po sya

[@Workshophobby2201]

Salamat Sir.

[@alfonzoidalgo9091]

Exelente modificasion

[@juankztech]

Mantap abangku👍👍👍

[@mo-ni]

oh WOW, nice job

[@LucinoPereira]

Top amigo 🎉🎉🎉 parabéns

[@gazirafik3473]

good get good brother

[@VelKAMAZ-g4w]

ты создал топливную аппаратуру😂

[@jefersoneleuterio3817]

Vendo esse projeto percebi que da pra fazer uma bomba para calibrar bico injetor de caminhão .

[@javiermorales2020]

Aqui existe un gran error garrafal.......😮😮😮😢😢😢😢😢

[@jairomota5825]

show parabéns

[@LabeepAL-Areeqi]

❤روعه

[@halaslife4571]

عمل راءع جدا

[@kayfeesiktany6127]

❤

[@المبرزي-ث3ث]

❤

[@ownthan3556]

Ok

[@こぶはな]

油圧ホース取り付け場所間違いだろ すごく使いにくいと思う

[@henriquecesarpremoli9019]

Uma gambiarra de quinta 🤦‍♂️