Vauxhall Fiat Alfa Saab 1.9 Pierburg Intake Manifold Swirl Flap Blank Blanking Removal Repair Kit

[@wakawu]

Or cut threads and just put a small bolt in?

[@Fisiek_Inferator]

I'm wondering what is the point of applying the grease before applying a glue????

[@RatiGabisonia]

why to destroy low speed power doin this?

[@user0not0available]

Is there a kit for the 1.9 TTiD manifold?

[@manzoor26]

What's the difference between the first kit and the second one? And which ones better?

[@ang4r]

grease first and then adhesive ? no cleaning at all ?

[@X8RLtdUK]

It's always a good idea to clean up the manifold as well as you can these are normally very full of carbon build up.

[@newsoundAG]

These turbines do not drop and cp? Or is it better to say that it does not decrease the engine power in acceleration?

[@carbonamigo]

Do i have to make software corrections after fitting them?

[@X8RLtdUK]

No, providing the actuator motor is left connected electronically the vehicle won't detect a fault.

[@iznogudsultan]

Hello, I have reviewed your video which explains a lot about how it works. Unfortunately, I can't find a video of this kind anywhere for the opel astra h z17dtr. I have big problems with it, I changed everything, and even put in a new turbocharger, but it still smokes black smoke, sometimes bluish, and when it starts twitching at two thousand rpm it throws out a P0299 error. smoke very well and lose traction. Please help and explain about replacing the intake manifold. THANK YOU

[@MrVukovicivan]

jesi rijesio iznogude

[@gurdalahmet2393]

Do you have model for opel astra 1.9cdti 150CV 2006 ??

[@brianbarton5495]

Have you had any reports of these plugs coming out afterwards.

[@X8RLtdUK]

Hi, no we have not had anyone say the plugs falling out if that is what you mean. - Georgina, X8R Ltd

[@ejiolamhenstephen1358]

How can I repair this problem in my 2002 Nissan pathfinder v6 3500 it's not firing it's showing Swirl control valve control solenoid valve on computer what can I do help me with a video

[@georgecrowhurst2050]

Hello would I need to get remap for this ?

[@catenomavica6878]

Are good also for Fiat grande punto 1.9 multijet 8v?

[@X8RLtdUK]

Hi there, potentially. Please email us on [e-mail] with the part number from your intake manifold and we can look into this for you. - Georgina, X8R Ltd

[@lazarpetrovicc]

Are the flaps on the second type which are secured with screws made from plastic or are they from metal? Great video.

[@X8RLtdUK]

Hi there, The screws that retain the original flaps are metal. Hope this helps!

[@RevFilmore]

How does this affect emissions and overall function? After all, the swirl flaps have been designed into the manifold for a reason.

[@X8RLtdUK]

This will have little affect on the emissions of the vehicle

[@rolandver3227]

It is designed for optimal fuel and air concetracation makeing, if you remove it your engine will work in low rpm with too much air and you lose power....

[@jaroslawchmiel3410]

Nothing like you said. Swirl flaps only regulate exhaust gases, that are recirculated by egr valve. Original air intake is not effected by those.

[@alejandroperez5368]

@@jaroslawchmiel3410 No, they do change the way the car accelerates. It improves acceleration on low and high RPMs by opening or closing the flaps.

[@redihoxha2940]

I have a Fiat bravo II year 2007 1.9 diesel 150ps, the same as opel and Saab. I needed to open and clean that intake minifold. What should I buy before I open it?

[@salvofarnia8046]

A new one and fit egr black and map it out

[@salvofarnia8046]

Blank

[@louistroughton3352]

I've done this on my saab 93 - but now has no boost at all? I just left the actuator plugged in to the sensor but not in it's origional place - does this matter ? Any help would be great

[@gwo7610]

Did you use a new intake gasket? theres no reason why this would effect boost other than an air leak from the manifold itself.

[@TheRik1970]

I had same issue was ok revved fine drove fine for 5 mins til engine warmed up then went into limp mode any advice???

[@furkanislek1244]

Merhaba benim aracım opel vectra 1.9 cdti z19dth motor. Benim aracımın sorunu geç çalışıyor. İki veya üç kere marş tekrarı yapıyorum. Araç 2. Marşta başlatmada çalışıyor. Enjektör sağlam , kızdırma bujileri sağlam sizce sorun nedir ? Hava sıcaklığı 20 derece olsa bile çalışmakta zorlanıyor. Marş motoruda sağlam akü , pilde sağlam

[@emrekula9900]

Merhaba aynı sorundan muzdaripim 9 ay olmuş paylasim yapalı herhangi bir çözüme ulaşabildiniz mi?

[@fl.sandgaard1084]

why remove flaps

[@X8RLtdUK]

Faulty swirl flaps can cause the engine management light (EML) to be lit, high fuel consumption, rough idling, rough running, poor power and torque, smoking from exhaust and error P2279-11 Intake system air leak,P2075 fault code. Deleting the swirl flaps removes these issues. - Georgina, X8R Ltd

[@alejaz8403]

Do you put the actuator back in with Manifold?

[@salvofarnia8046]

Yes

[@MrVukovicivan]

This model is 16valve

[@daniel2312ivana]

What do you get them fixed? Is this some glue or something else?

[@Kumodraz1987]

they have some gum, how you see, to fix them :D

[@ItsFriscoBaby]

Does the manifold have to be removed or could the swirl flaps be removed from the top (the type that doesn't have screwed on flaps)

[@paulMason-zm4kr]

Did u ever get an answer to this question I was wondering if they can just be lifted out without removing manifold also Did u do that Does the car run better starting ect with blanks installed

[@rickyhalpin4447]

@@paulMason-zm4kr did you ever get an answer to this question? I'm going to attempt to just lift out tomorrow 😄

[@paulMason-zm4kr]

@Ricky Halpin oh this was from years ago but I ended up removing manifold and tbh it wasn't that hard to do. Once it was removed i split the manifold and completely cleaned out the manifold insides and all other parts going to it and blanked off the ports with plates I bought of ebay.also connect the power back onto the rod so no alarms cone up just so it thinks it's doing what it's there for After fitting back on car it has so much more power it seemed to much for the front to handle. Well worth doing only 1 issue I had was when you lock of the fuel pump pulley there is a woodlock key which was an absolute pain to refit without it falling out as its upside down Took me about 10 attempts

[@rickyhalpin4447]

@paul cheers for the reply, I've planned to remove 3 and leave the one that's attached to the arm for now, cambelt is due in a few months anyway will get a mechanic to do the rest then 👍

[@RedEyedJedi]

Yes the manifold needs to be removed. Once you've removed it, its well worth splitting the manifold in half. I think there are like 14 bolts holding it together and a couple of metal dowels. You can then completely clean it of all the carbon build up and trust me, it will be full of carbon. I just did mine.

[@rbasegmez9460]

will I get any problems blanking it ?

[@X8RLtdUK]

Not likely, the blanking of these manifolds improves mpg/ overall fuel consumption in some instances.

[@jaroslawchmiel3410]

I'd rather say, that it restores fuel consumption from before swirl flap failure. After blanking mpg went back to what originally I had.