Yes you can freestyle a deadcat frame

[@waskyfpv759]

Your neighbours have to love you for this beatiful sounds in the sunday morning :D

[@hammerdinnii]

Oh yeah!

[@NONX01]

@@hammerdinniihello sir! I took the screws out of my Geprc Mark 5 to adjust camera angle of O3 unit, I set it as I wanted, now I wanna put the screws back ( they are all exactly same, 4x ) and they just stuck half way??? Like I can screw them back in just a little bit and then they both stay in the same spot leaving like 3mm gap to the actual drone. I tried to push a bit heavier but no help and also don’t wanna try pushing really hard and break the camera lol. What is going on? Please help me I beg you I’m losing my mind I got this drone 7th day now and I still wasn’t out flying cos there is ALWAYS a problem. I just finally charged my bats, set everything on Beta Flight and now this💩. Omfg…. Please help 😞

[@hammerdinnii]

@@NONX01 Check the Threads: First, ensure that the threads of the screws and the corresponding holes are clean and undamaged. Sometimes, tiny debris or damage to the threads can prevent the screws from going in smoothly. Alignment: Make sure that the camera and its mounting bracket are properly aligned with the screw holes on the drone. Misalignment can cause the screws to not fit properly. Cross-threading: Be cautious of cross-threading. This happens when the screw is not correctly aligned with the threads in the hole and starts to cut new threads, damaging both. Start by gently turning the screw backward (counterclockwise) until you feel a click, which is the threads aligning, and then screw it in. Use the Right Tools: Ensure you are using the correct size screwdriver. A screwdriver that is too large or too small can make it difficult to apply the right amount of torque. Gradual Tightening: If you have multiple screws, do not fully tighten one screw before starting the others. Instead, start each screw and then gradually tighten them in a cross pattern. This ensures even pressure and alignment. Manual Guidance: If the screws are magnetic, sometimes the attraction can slightly misalign them. You might need to gently guide them by hand to ensure they catch the threads correctly. Lubrication: If the screws are going in too tight, a tiny drop of light lubricant on the threads can help. But be very careful not to get lubricant on any electronic parts. Do Not Force: If a screw won't go in, do not force it, as this can strip the threads or damage components. It's better to step back and reassess.

[@NONX01]

@@hammerdinnii I’m just an absolute imbecile🤡 and because the camera sat there so solid still even without the screws in - it seemed like it’s only moving up and down like a gimbal…. but I grab it and tried to move and I could move it anywhere 😂 just had to fit the hole I was looking for. Sorry for your time and thank you for you time 🙏

[@NONX01]

@@hammerdinnii I was out today, had a nice trial flight, landed fine ( as I was maybe half a meter above the ground I double clicked my disarm AUX 4 button ) and it did cut it off -> the drone dropped down fine but then as it dropped and was on the ground it was still all shaky with motors running like it’s ready to take off any time again O.O I was like what the hell… I kept pressing disarm button twice multiply times, but I only could see “Motors started” every time I was trying to do that, would never see “Motors stopped” notification -> THEN I wanted to see if it’s gonna go up again and it did as expected but it also flipped in the process so now it’s upside down - I again tried to disarm multiply times as it’s flipped, then of sudden the motors start reving like crazy, I tried to disarm one more time ( exactly same way as the entire time ) and it finally stopped… I could hear motors sound fading away and finally ve seen “motors stopped” notification popped out. Why did that happen? Whats the problem? It must got “disarmed” mid air when I tried to disarm for the first time, but it seemed or felt like as soon it touched the ground - the motors went back on... It literally cut the power, dropped down as if it’s off, but the motors were still running and it took me about 10 attempts of trying the same thing( double clicking AUX4 which is my disarm button ) but it wouldn’t go off, till it finally did. Why it didn’t go off right away?!

[@FPZzzz]

I was thinking the Apex deadcat so no props in view with the 03. Are you running 6s on 4s kv? Lol.

[@hammerdinnii]

6s at 1750kv

[@robgroove]

Have you tried some fast yawspins?

[@endyX286]

nice one bro..so fast.

[@lylylucy]

damn ur a good pilot

[@DemiBogart]

Yo! I know this is late, but can I have or know your rates? Sick flying dude!

[@carternickles3464]

Holy Moly

[@Saruul_osman]

Wow so fast. 😳

[@guineapiggaming2048]

What motors are you using?

[@hammerdinnii]

@@guineapiggaming2048 XING 1750kv

[@TheCloudwalkerFPV]

Jeer Deezus! How much up tilt are you using?

[@hammerdinnii]

I cant remember but it should be 20-25 degrees up tilt

[@mk_quattro]

Deadcat, but still has props in view?

[@hammerdinnii]

Ultra wide on the action 2 is crazy good

[@aravindshreyas3571]

hello, what motors are you using?

[@remyKhuong]

What controller you r using? Can i have your Spec plsss❤

[@hammerdinnii]

Im using the RadioMaster TX16s mk2 Frame: bit.ly/3CpfpT2 ESC: bit.ly/3p2mDt5 Flight Controller: Comes with the stack Props: [www.getfpv.com/ethix-s3-water...] Camera: Dji O3 Air Unit Camera VTX: DJI O3 Air Unit Battery: bit.ly/3P4e6R0 Action Camera: Dji Action 2/Gopro Hero 10

[@Frumundaair]

Is it the deadcat 5 inch or 6 inch

[@hammerdinnii]

5 Inch

[@Frumundaair]

Nice what about motors?

[@hammerdinnii]

@@Frumundaair iFlight XING-E Pro 2207 Motor

[@graviball]

Yooooo😮😮😮

[@atxrefuse]

Its me feakfpv lol, and you can but the yaw wobbles bother me so much ong.

[@powersv2]

Is this a stock tune?

[@hammerdinnii]

No its the supafly tune 5inch

[@Arcticfawksie]

I don’t think anyone has said that tbh

[@lylylucy]

when I read the title I remembered that guy who made a drone with a dead cat instead of the drone's body kzbin.info/www/bejne/rWnckpSXdr9nqJY idk why they did it but they did it xD

[@jesuschrist8068]

That video is the reason its called that.

[@rayang9929]

you really just brought my imagine to life there bud, good shit! XD

[@griffey11]

Lmao wtf

[@Xcx284]

U fast forwarded the video. The frames doesn’t add up. Plus, those flips aren’t clean, clearly because of its dead cat design

[@hammerdinnii]

@@Xcx284 ?

[@Lex1uth3r]

Whatchu talkin bout Willis? This was clean AF with a dope ass landing. Lets see you try to top it, or even come close. We waitin...