Battery Hack - Kinzo 44p9500 - Parkside battery pap 20 a3

[@davidmatthews4773]

I have recently (the last 12 months) been buying parkside 20v family tools as I they became available in Lild. I found your channel a few days ago and I find it fascinating as to what can be done to repair and hack the tools. I will be watching in the future and using a lot of your ideas in a practical way. Thank you. Oh! Forgot to say I have subscribed.

[@zana3587]

thank you sir i hope it's helpful for you

[@davidmatthews4773]

@@zana3587 the videos have been very helpful and given me some ideas. Thanks David

[@luisubilla7941]

Muy buen video saludos desde chile mi pregunta es ? La bateria que adaptaste era de 20v y el atornillador tambien? O era de un voltaje diferente?

[@zana3587]

Gracias señor, era el mismo voltaje.

[@Deadeye0815]

Be careful !!! Parkside Battery's don't have a Low Voltage cutoff (no MosFET inside). So it depends on the Tool to cutoff and prevent an over discharge ...

[@martinleska4292]

Nice idea but NOT with Parkside battery pack! Beware of this modification! Parkside 20V battery has no undervoltage protection in battery board! This protection is integrated in parkside tool speed controller. Cells are connected to output pins directly and you can discharge battery too low and destroy one cell in few discharging cycles. Even with one cell below 2V, original charger refuse charging with error light. Dont try this modification!

[@zana3587]

thank you sir, yes, but it's good for me, before it's discharged i stop

[@mVik85]

@@zana3587 simple solution for that is small voltmeter in the handle, see here: kzbin.info/www/bejne/mHnImpxuaJmooNU

[@adamnaser1852]

Peace be upon you, Mr. Dahen I have a FERREX drill 20 volt without battery. Can I use another type of battery and how can I know the negative and positive to operate the drill because it has 5 outputs (+B1- /B2- / T / B1+ /B2) Thank you for your help

[@АнтонПетров-о1й]

Нормально получилось аккумулятор примостырить. Поздравляю с новым инструментом!!

[@zana3587]

Спасибо, сэр

[@lehrjunge6206]

Cara, eu moro no Brasil, mas isso vai ajudar bastante com uma parkside spindlelock. Ótimo vídeo.

[@zana3587]

obrigado senhor

[@ruinunes8251]

One thing is for sure, when my chopping boards get old they are not going to the bin anymore.

[@zana3587]

yes, thank you sir

[@arturalbertomartinho2103]

Excelent work. I learned. Congratulacions.

[@zana3587]

thank you sir

[@وَإِذَامَرِضْتُفَهُوَيَشْ-ض5ك]

عمل رائع أسألك استاذي اذا اردت شحن البطارية لنفترض مثلها 21 فولط من الشاحن الأصلي كيف اعمل مع الخيط الثالث الشاحن ما يشحن وشكرا

[@Muhammad1977ma]

أحسنت أستاذي المبدع والله ادهشتنا بعملك انتا تعمل من إلا شي شي جميل 👍👍

[@zana3587]

اشكرك اخى العزيز

[@taico6061]

Nice hack! What's type of plastic plate did you use ? pls

[@zana3587]

Thank you sir . I use kitchen plastic chopping board

[@taico6061]

@@zana3587 ah yes ! like the sausage cutting board :)

[@isaacnguyen6944]

Nice hack. Talking about battery pack/dedicated charger, looking for compatibility between manufacturers on the web I ran across many site warning about mixing. I think it is BS as the charging logic and protection is always in the battery. The charger is just a transformer. Alsö the battery/Charger from parkside are interchangeable with Güde. Just a little bit of plastic to grind here and there. I guess there a lot of other compatibilities out there.

[@zana3587]

thank you sir i hope it's helpful for you

[@stevebabiak6997]

There is another aspect besides charging, and that is sensing when the battery voltage has dropped too low for it to be charged in the normal manner in the charger that matches the battery. There is a circuit board that is known as BMS (battery management system). It functions to charge all cells so that they are somewhat closely matched in voltage at full charge. In some batteries, it also detects the low voltage situation and cuts off the power; but some manufacturers put that function into the tool. So this is the thing to be concerned about when mixing batteries from one manufacturer and tools from a different manufacturer.

[@2003comix]

You are the best repairman!!!

[@zana3587]

thank you sir

[@christopherbooth1772]

I was just looking at buying a 3d printed adapter to makita nicd reciprocating saw looks like i be skipping that and buying a cupple £1 chopping boards many thanks for the video

[@zana3587]

thank you sir i hope it's helpful for you

[@christopherbooth1772]

What glue do you use? I've tried 3x different 2 part epoxy and all 3 brake free with use

[@stevebabiak6997]

@@christopherbooth1772 - it didn’t appear to use any glue. There were four screws that held the pieces together, with nuts embedded into the topmost layer by heating it up to soften the plastic for press fitting the nuts.

[@farruxyuldashev125]

Здравствуйте скажите пожалуйста инструменты parkside качественные или нет

[@zana3587]

привет сэр, нет, это не хорошего качества. но лучше из китайских инструментов

[@orlatris96]

Muito bom, parabéns, grande trabalho

[@l.d5512]

C'est très bien fait et assez économique.

[@zana3587]

Merci Monsieur

[@العطوانيباسم-ن9ه]

احسنت عمل رائع انت مبدع في عالم الصيانة

[@zana3587]

اشكرك اخى العزيز

[@MihaiParpalea]

Nice work, but I expected the lighter to be Parkside too :)

[@zana3587]

thank you sir

[@kaboncho]

Good job 😊😊

[@rashidmohamed269]

ئەم درێلە دیتم بە 5000 دینار دەیان فرۆشت ..دەستت خۆش بێت کارێکی جوانە.....

[@zana3587]

بەریزی کاک رەشید

[@CL-wj6wv]

Good work 👍

[@zana3587]

Thank you sir

[@Mustafa.B2]

First like. Great idea my brother.

[@zana3587]

thank you my brother . my teacher

[@ngodinhtrung8907]

Great 👍..Sir

[@zana3587]

Thank you sir

[@chaotajai]

Buen trabajo 👍

[@zana3587]

gracias Señor

[@alidilshad9741]

ده ست خؤش جوانه

[@zana3587]

زور سوباس . بةريزي

[@Pinkycze]

Parkside battery dont have BMS soo this is the best way how to kill battery

[@zana3587]

thank you for your information!

[@tzvetankirkov2340]

Great work! What does it mean "BMS"? And what will be the problem? I have kinzo too, with old battery and wish to recover it! Thank you!

[@stevebabiak6997]

@@tzvetankirkov2340 - BMS = battery management system

[@flippy9133]

be caurefull those batteries have no undervoltage protection as its in the tools, this can ruin your battery

[@zana3587]

i know sir

[@جعفرمحتوياتعامة]

🌹🌹👍👍👍👍💓😍❤️🌷😘

[@juanc.h.s.7026]

muy interesante la adptacion de la base.. saludos

[@zana3587]

gracias Señor

[@chahidabdelmjid5653]

Bravo,respect

[@zana3587]

Thank you sir

[@shervinsafarzadeh1673]

good😮🤘👍👍

[@zana3587]

Thank you sir

[@k1w177]

very dangerous ! the battery has no shut-off electronics, shut-off and protection are in the parkside devices! operating the battery without this electronics is not only careless, but also dangerous

[@zana3587]

It is not that dangerous because the battery has a fuse, the piece is used to cut the power when the battery is weak

[@k1w177]

@@zana3587 the fuse is is only the last emergency protection, the device must be switch of the power from the battery, if the battery give the signal to switch off, you not connect the signal pin, and you not have the electronic to switch off

[@georgegeorge899]

You can't go more China than Kinzo ! 🤣

[@zana3587]

hhhhh yes sir

[@mick1gallagher]

After all that hard work you still end up with a piece of junk

[@zana3587]

it's better from nothing

[@elizangelacarvalho919]

Muito bom

[@zana3587]

obrigado senhor

[@robertrydzewski1083]

To jest to nie każdy ma drukarki 3D

[@igotbricotools2035]

👏👏👏

[@zana3587]

thank you sir

[@kahlid-ataya]

انت بطل

[@zana3587]

اشكرك اخى العزيز

[@hardwaretools1428]

woooooooooooow god god god

[@zana3587]

Thank you sir

[@cadmin]

😂😂😂😂😂

[@zana3587]

Thank you

[@karinhiwa812]

Slaw to kurde

[@zana3587]

بەلی بەریز

[@karinhiwa812]

Sarkawtobe inshala la kwe dadanishe

[@zana3587]

سوباست دەکەم . هەولیر

[@karinhiwa812]

Sarkawtobe datwanm prsiarakt lebkam

[@zana3587]

فەرمو