Finally got around to installing the manifold for my 2 door Civic. still got alot to clean up on the lines and hoses, but its installed.
Пікірлер: 52
@headshotheroes26183 жыл бұрын
This Is Awesome, Great Video. . I have a 2000 Civic Coupe DX but Auto, but later I'll have it swap to Manual (that's gonna take a while though, it's not in my Budget Yet 😔, Slowly but Surely though) but for now I would like to do this. I'm looking at a mani on Amazon, but I'm scared to buy it cause it might not be compatible with my car. Any Tips from you or anyone on YT Will be Appreciated. Keep up the Awesome Vids and Aloha!!!! 😊👍🤙
@juani7495 жыл бұрын
I have a d16y7 automatic engine and i bought a y8 at intake manifold and his respective throttle body. Can i use the Y8 throttle body or i hace to swap to Y7 throttle body?. Ty
@ronnmotoph15423 жыл бұрын
What kind of pipe you used sir?
@jaycrawford41485 жыл бұрын
If I don't run my fuel pressure regulator vaccum hose to the back side like u did and run it to to one should I plug the back one
@VarnHomestead5 жыл бұрын
yes always plug them if you aren't using it.. or you will have a vacuum leak
@historyhunter52156 жыл бұрын
Want to get rid of the check engine light? Pull the cluster and take it out....😂😂😂👍
@stocklifekustomz71894 жыл бұрын
HistoryHunter hey can I hit you up about parts if so hit me back thanks mike the names
@richardparent51055 жыл бұрын
Idk what to do I have a 98ex and put a y7 in it and running my y8 manifold and don’t know what to do when I use the stock y7 computer the car won’t idle right. If that just run I’m using the y8 harness and don’t know what to do need help please.
@TristonSmith_ThePlumbingSmith5 жыл бұрын
Check your throttle cable too
@albertano69695 жыл бұрын
What size hose did you buy and how many feet ? After did it run good no check engine light or issues ?
@VarnHomestead5 жыл бұрын
I don't remember the hose size but I got 2 3 foot pieces. As long as you hook up everything correctly it should run fine no issues or check engine lights. Mine has been running fine since the swap, got a lot more torque it was noticeable.
@hsktech88243 жыл бұрын
What rims are those??
@MGModz4Life4 жыл бұрын
What is the name of that short ram intake and where u get it from?
@VarnHomestead4 жыл бұрын
That is just a cheap DNA short ram from ebay. like 30 dollars..lol it works
@Doubleodude6 жыл бұрын
Very cool. I’m guessing this increase the horsepower?
@VarnHomestead6 жыл бұрын
yes, a little and more torque. The original manifold is terrible on these engines.
@mahermulla99724 жыл бұрын
@@VarnHomestead very true this manifolds kicks in VTEC like never before
@poboypowder75673 жыл бұрын
@@mahermulla9972 this engine doesn’t have vtec ://// the y8 does but not y7
@sergiochaparro42983 жыл бұрын
What harness are you using for your swap?
@jguardipee902 жыл бұрын
You use the same harness everything buttons rite up just remember to label your wires
@webkikif2 жыл бұрын
Where do you get a d8 intake manifold?
@VarnHomestead2 жыл бұрын
Junk yards
@seangraham55644 жыл бұрын
What gasket did you use?
@VarnHomestead4 жыл бұрын
y8 gasket.
@jeffquinones40076 жыл бұрын
Is your car auto and you used a manual intake?
@VarnHomestead5 жыл бұрын
No my car is a manual, the IACV on this Y7 is on the throttle body. The manifold for the Y8 "manual" has the IACV on the manifold. If you use the Auto Throttle body you wont have to block off the holes.
@stevedelrocini35643 жыл бұрын
I was gonna say did you not peep the clutch reservoir
@blavoblouintel5 жыл бұрын
whic swap is better y8 or z6
@hondahouse62255 жыл бұрын
Z6 more reliable
@garymijangos94035 жыл бұрын
Z6 better head vtec hits harder on z6 and it’s a better build y8 aren’t bad but they tend to have messed up bearings over time because it’s not lubed properly the y8 has the better intake manifold tho. Z6 is more reliable because it’s built better
@TristonSmith_ThePlumbingSmith5 жыл бұрын
@@garymijangos9403 no its not
@francusati4 жыл бұрын
Esto realmente vale l pena
@osomayor70834 жыл бұрын
frank cusati lo has hecho ? Tengo un y7 quiero hacerlo así o cambiarle la cabeza de y8
@richardparent51055 жыл бұрын
WHAT did you do about iacv? Are you using a stock y7 ecu
@mushy181005 жыл бұрын
Richard Agustus i believe he’s still running a factory ECU
@leopaulevans75736 жыл бұрын
how mouch power gain did u achieve from y8 mani
@VarnHomestead6 жыл бұрын
you don't really gain HP. If so its not noticeable. I did gain a bit of torque though.. faster off the line defiantly.
@hondahouse62255 жыл бұрын
15 20hp
@NormanMcGregor6 жыл бұрын
Way to complex for my mind! Lol
@VarnHomestead6 жыл бұрын
I was a bit of a learning curve when I first learned about this kinda stuff but eventually, it all made sense. engines are amazing things.
@NormanMcGregor6 жыл бұрын
I'm not a mechanic but the stuff he does seems to work just fine!
@VarnHomestead6 жыл бұрын
Everyone has their own way of doing things, If it's over complicated, well mabe to you but not someone else. I would rather move the presure guage then hack up the throttle body cam ear as I can use this on a different engine when I get an upgraded throttlebody.
@NormanMcGregor6 жыл бұрын
The Dude is a DORK!! Don't let it bother you buddy!!
@VarnHomestead6 жыл бұрын
not sweating it. I think he is a troll, You never know though everyone's the youtube master mechanic. ft it's not fitting just get a saw and hack off half of it...haha I am just sharing what I have learned along the way. If someone doesn't like it.. they can make a "better" video and upload it..lol