ZF 6HP Transmission Solenoid Replacement (BMW/Jaguar/Range Rover)

This video goes over replacing the solenoids in a ZF 6hp transmission. This DIY is usable for most of the ZF 6HP transmissions : 6hp21 6hp19 6hp26 and other variations. You can use www.thectsc.com to find your part numbers and even to buy solenoids and other transmission components. If you want to purchase them from me, you can do so by contacting me through www.shoplifetv.com
When replacing the solenoids you should also replace the mechatronics sleeves : bridge adapter, valve body sealing sleeves, plug adapter, filter and fluid (only use ZF Lifeguard 6).
Here are the links to the other ZF 6hp Auto Trans videos I have uploaded:
• ZF 6HP 6 Speed Auto Tr...
• How To Change ZF BMW T...
Support my channel by becoming a member using this link: / @shoplifetv
My Amazon Store: www.amazon.com/shop/shoplifetv
Buy My Merchandise: www.shoplifetv.com
Ask me a question: www.shoplifetv.com
Request a Shop Appointment: www.shoplifetv.com
Instagram: @ShopLifeTV
/ shoplifetv
My vlog channel: / shoplifevlogs
KZbin Business Inquires: Email me [e-mail]
Disclaimer: Some links will contain affiliate links. Due to factors beyond the control of ShopLifeTV, I cannot guarantee against improper use or unauthorized modifications of this information. ShopLifeTV assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. ShopLifeTV recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of ShopLifeTV, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not ShopLifeTV.

[@LarryLane07]

I don’t know what I’d do without you. You’re probably the most important person in my life

[@macalvarezLA]

He is not, Larry 🤣

[@LarryLane07]

@@macalvarezLA 😄

[@ThePrincess0617]

I just want to tank you very much, I had a nightmare with my BMW 530i transmission and was quoted $ 2,800 to get it fix in the best case scenario and the worst to buy a new transmission. I followed each step on this video, purchased all what you recommended and was very hard for me to do it without a lift in my garage but guess what ? I did it and the transmission is working as new now after the repair. All the codes on OBD gone, no more transmission messages on the car and only cost me about like $700 for all the parts. Thanks again, you are great !!

[@Dangbo3030]

@nune nemaveze , I would start off with a fluid and filter change. Find a reliable shop or do it yourself. It's easier with a car lift though.

[@bryanderksen4448]

I recommend removing and cleaning the pistons which sit in the valvebody behind the solenoids. Also, give the hole a squirt of brake cleaner. All that dark fluid contains clutch lining material which can get trapped in those holes and interfere with the movement of the pistons. I was trained to cycle the piston in and out to detect any burrs or interference in the movement. A sticky piston will not be cured by a new solenoid.

[@ShopLifeTV]

Thats a great tip! The sonnax kit is a good way to fix other issues with the valve body. I will eventually make a video on that as well.

[@bryanderksen4448]

@@ShopLifeTV Any way we BMW fans can help each other out! Your videos are excellent btw. I have been following you for about two years. Keep up the good work!!

[@KennethWalker-ei6rf]

😊

[@jacoblami1731]

If you're going to clean the rubber ones that come with it you might as well buy the $50 metal upgraded ones...they use a spring to press the seal rather than relying on the rubber to say supple. Just makes sense if you're going to go through the trouble of dropping the pan and cracking open the valve body.

[@bryanderksen4448]

@@jacoblami1731 Can you provide a product link please?

[@michaelconatore4720]

Very well presented. Gives me confidence to tackle this job myself. Thank you!

[@infamoussgarage]

This video was 100% on point. I raised my rover up dropped the megatronic unit and got all new solenoids from ZF with the tubes and new gaskets. My rover drives 100% better shifts are smooth as butter now. Thank you for this video

[@Dustinsfishtanks]

Bro- and then I get a 550i and you show my exact mechtronic. I owe ya big time brother!!! Great teaching- great content

[@ShopLifeTV]

awesome! congrats!

[@benaragon12]

Dude, So I have a Range rover with this transmission. I watched your video sereral times and bought all the parts. I did this job in my driveway with my son and it worked out perfectly. Thank you so much for providing this. You saved me over $1000 if I had Land Rover to do it. I know this doesn't help the small business cause you are providing a step by step but I really appreciate it. Inserting the new umbilical sleeve was giving me a hell of a time but I watch again and bam it went in! Anyone reading this , don't be afraid to do this work. Its not that difficult especially if you wact his video. THANK YOU AGAIN. 😀

[@Mrbeest0]

Was your rover able to shift into any other gear?

[@benaragon12]

@@Mrbeest0 When it went into limp mode it kind of stayed there until I cleared it with my scan tool. But eventually the solenoids really started to fail so I was forced to fix it. As noted in the video change all the parts all at once. Cause once you break the sealing surface from the mechatronics unit, you have to replace the 3 black tubes that transfer fluid back and fourth. I did not do that and had a pause between 1st and 2nd gear. Ordered the parts on amazon and took it apart again and replaced the tubes and the slipping went away. Also get several cans of brake cleaner to blow out debris from all the ports , just in case. The step I had to review in the video was how to install the new electrical umbilical adapter. Pushing on it with a pry bar finally got it to seat. I had to let the transmission re-learn again by driving 0-60 and let it coast to a stop, no brakes. But it is running good now.

[@infamoussgarage]

@@benaragon12before you let it relearn did it shift weird. Hard shifts ?

[@benaragon12]

@@infamoussgarage yes… you have to find a road that you can take it up to 60 and coast to a stop . Do that about 3 times.

[@infamoussgarage]

@@benaragon12 mine is doing that now. Did yours throw limited shift when it shifts hard ??

[@uswwt]

Awesome video!! I call this the big boy's version of Lego. It seems super easy to follow your video. This makes me super tempting to tackle these jobs myself instead of paying someone to do it. Although a bit of elbow grease and sweat are needed. I have already done a lot of work on my car myself, saving a ton of money is one thing. Such jobs are super interesting and satisfying.

[@michaelsbraga2561]

Jason! Between your input into ZF 6hp 26 transmissions and input from Eriksson Industries, I changed the solenoids and seals on my 2008 L322 Range Rover HSE and it now shifts flawlessly. Your video instructions are very detailed. Thank you.

[@ShopLifeTV]

That's awesome!

[@robbiewalker3]

Did you reset the adaptations or did you leave as it ?

[@michaelsbraga2561]

@@robbiewalker3 By adaptions, if you mean driving at a certain speed and Kerri f it coast and slow down on its on, I did several times and then just drove as I normally do. Very hard to find a road where I live to do that.

[@MePeterNicholls]

Something about this video is so satisfying to watch

[@jralvarado5001]

What was a $3300 quote to fix my Transmission became a $900 fix.. thank you brother big time..

[@atlantajunglepythons1744]

Outstanding craft to make the vids and present this info soberly, and completely. This is a deep enough subject that it should be approached with good technique and an appreciation of the parts involved and the order in which they are touched. I'll be glad to do this work and not have to crack into rest of the transmission. Should the need come up it will be time to swap!

[@DavidLopez-pz6ue]

Life saver 💙this man needs more subs👍

[@TheFrenchPug]

Soberly?

[@kdao1007]

EXCELLENT TUTORIAL VIDEO STEP BY STEP, THANKS SO MUCH~~ i Just finished switching out all the solenoids and harness on my 2008 BMW 750li. I'm hoping this fixes all the issues with electric parking brake (replaced the gear in the trunk). And the codes for solenoids in trans. There was lots of transmission oil drained out so will refill with the ZF Life 6. This video is amazing and really appreciate very detail steps. I used this video and the other one to install the megatronics back into the trans and put on new trans filter and bolts. The valve sleeve was a bit tricky. It sure does how that megatronics in. Definitely needs to be remove first.

[@robertfaulkner7152]

Awesome video! Thank you so much for sharing your knowledge. definitely makes servicing these transmissions a lot less daunting!

[@747instructor]

Outstanding video and great job. It got me through my first solenoid change after having shifting issues on my 2012 BMW 750LI Xdrive. Answered a couple of questions during the assembly process when the spring pushed out the plunger and I didn't notice the orientation of the plunger. Also the location of the shift linkage insertion to the slider. Thanks.

[@miguelacosta7755]

Great video buddy! Here in Argentina we can't get a lot of information, and you my friend just helped me a lot! Wish for you the best and also wish you keep doing this kind of videos ! Hahaha

[@ShopLifeTV]

Glad I could help!

[@c.bambinglockleys]

Love your channel from the beginning ☺️

[@noord726]

Thank you for your videos, keep up loading, stay low and go low, Namaste, be safe for th whole family greets from holland amsterdam.

[@NENTECHM57]

Brilliant video, just right amount of information and all explained well. Enjoyed watching

[@parnellbanks1408]

MAN YOU MAKE IT LOOK SO EASY

[@marshallgoldberg8376]

After you do it fifty times, it’s easier.

[@IRIEAC]

Lov this .. you broke things down very nicely

[@ShopLifeTV]

Thanks! Glad to help!

[@jessebrown9046]

Great video bro, I just bought a 05 HSE 4.4 Rover for 500 bucks here in Canada, the guy said the trans was toast but I dont think it is, I can put it in drive, or reverse and it wont move, the truck is in awesome shape and worth changing the solenoids, I hope it works, Ill update when I'm done, thanks bro

[@user-gd9ii9lr9i]

Excellent video, very informative

[@muhamadsalameh9155]

GREAT EXPLANATION THANKS MAN

[@MrNicoe36cabrio]

Thanks, brother and sister for sharing. Hopefully, you will do this to a 7-speed DCT(GS7D36SG) one day. Mine is now on 50t miles and I want to change the oil and both filters in the near future. Dutch regards, Nico.

[@j.c.2214]

Hello thanks for all your knowledge and teachings. I am in the process of installing seals, new solenoids, new oil pan and oil on my 2010 528i. I do not have inpa which one should I get All the ones I have found only work on Windows 7 which is old I have window 10 and above thank you

[@e55v86]

Great channel, great videos👍

[@ShopLifeTV]

Thank You!

[@CZUNIGA36]

This guy is amazing! Thanks for sharing your experience 12-9-2020

[@dpmedina11]

hello ShopLifeTV. Thank you for this video. I have an E60. there isn’t any transmission issue per se, but after running a scanner, it mentioned 4E86 Solenoid valve 3 code. I was planning on doing this very video procedure, but you mentioned resetting the “adaptations.” How is that done? Thank you again for sharing your knowledge!!!

[@Stefan_Smith]

Omg you're my hero!!!

[@kasunkalutara476]

Well appreciated, just did my Range Rover L322 2011 Supercharged ZF Transmission oil/filter and rubber vanes replacement. I still have an 1,2,3 gears not shifting smooth on the cold starts. But when the temp rises and after drive for a while it smooths out, Appreciate some comments please

[@aarp6970]

Hi! Thank you very much for this video! I have a 2012 Land Rover LR4 with 116K. Never had any problems. Then one of the hoses of auxiliary transmission cooler got disconnected and I lost all the fluid. Refilled with original fluid, drove for 2 days without any problem other than shifting from 3 to 4 hard. Then stopped shifting to 4. It drives normal on 1,2,3 but can not shift to 4 and gives error code.. P0783 3-4 shift malfunction. Does this sound like a solenoid problem too?

[@Vash16xli]

They'll be a lot of people that'll need to see this. You helped me with this earlier this year.

[@ShopLifeTV]

For sure! Hope all is well!

[@mustafasahan7060]

tesekkürler cok faydali oldu

[@CCROSS5882]

excellent video

[@undrejohnson2588]

Thanks for the video, it was awesome...I have a 2002 745li bmw that needs the solenoids changed...how much do you charge?

[@GTP375]

Terrific video and thank you for the detailed video. I’ve got a Maserati 2007 with 6 speed auto. 6HP26 I believe. Would the procedure be the same as this video? Also, where can I buy the whole kit? Including filter and sleeves etc.

[@stevemcleod1124]

Great explanation! Planning on doing my own solenoid replacement based on your video. Just to confirm that I would not have to program the transmission after changing solenoids? Just drive normally around town and put some miles on it and it will adapt itself? I do not have ISTA/P and a dealer is an 8 hour drive from me.

[@MHTPRO]

Superb video

[@bradleygroenhof8183]

I run redline D4 in my 335d with no issues. A vast improvement over the semi synthetic oem fluid. Lifeguard 6 has boron that turns into boric acid as it breaks down and degrades over time. Ill stick with d4

[@arfetherussian]

Yeah I’m sure you can notice the difference between the Lifeguard6 and the D4 fluid😂🤡, 210k miles with Lifeguard 6 (multiple fluid/filter changes) and not a single tranny issue in my E70. Nothing wrong with the original fluid. Although it is a little pricey…

[@TheFrenchPug]

250k miles in my E92 using Liqui Moli. Also, use it in my wife's Mercedes. Shifts smooth as butter still.

[@mtbridingog9083]

Using valvoline max life and no shifting problems at all in my x5 3.0si e70

[@fraizer2600]

great video, how much cost those solenoids ? i have an E64 LCI 635D of mid 2009, i change the filter and all the parts you explain to change except the mecatronic part with selonoids. following the zf procedure and use ista to reset the oil. but i dont reset the adaptation. some people explain to do it but i dont thing is right because the car have 165.000 km and i dont change the solenoids... thank you for the advice :) last queqtion i will program the engine of the car on a stage 2 is risky if i reprogram gear box too ? is an full automatic.

[@overlandi5056]

Hi from here in Africa. Amazing set of video's. The same gearbox is used in the LR3. Mine tends to hold first gear a little to long instead of changing into second gear. Would you suggest the solenoids or something else? Many thanks.

[@mikejacobs4727]

Great video , I'm about to do this repair. I have a scanner and the trans is not overheating . I changed the fluid way to late ( it was black ). After the new zf 6 fluid the car ran well , but I have a slipping issue 5-6 gear back and forth and getting gearbox fault. When I changed the fluid I admit I got lazy and didn't change valve body seals . I just ordered cellenoids and am gonna do this repair this weekend . Where is your shop located ?

[@ketoduo6117]

Nice job! Thank you.. I have an 06 LR3 with a P0501-00 code and the transmission won’t engage. If I undue the battery for a while it will go away. When I start it back up, I can drive it for several yards & then the p0501 pops up & the trans disengages. Does this sound like the, “losing pressure” you were describing? Do you believe this service will fix my issue? I realize the p code points elsewhere & I’ve ordered new speed sensors. I’ve also cleaned the TCU and it looks great.

[@jasonturner1590]

Great video thank you so much

[@ShopLifeTV]

Glad you enjoyed it!

[@timportoulas8606]

Thanks for your great content. I dont know if solenoids needed or seals. I have 100k miles and its really acting up. I hear a rubing squeaky noise when i go around a turn, sometimes it slips between first and second.

[@pullcollector2714]

Can you please make a video similar to this but with the GM transmission?! Or are both transmissions the same? Selenoids? Seals? Etc...

[@artest7]

Is this procedure the same for Fords or my 2006 Lincoln Navigator w/ZF 6HP26 A/T with Mercon SP Fluid. I think I can replace the fluid with Mercon SP. otherwise wouldn’t I have to get 100% of the current fluid (SP) out (which is a lot more work) in order to use Lifeguard 6)? Thank you for this video (if I can use it)!!it’s the most comprehensive solenoid/mechatronics replacement for the ZF 6HP26!! Great work!! 😃

[@mancao8936]

Great video, my car range rover 2006 ZF transmission. The D automatic drive stuck at 3rd gear, but the standard S is working fine. I can shift all the gear to run the car. If I do not replace the rubber tube as this video, will the standard shift will stop working when the rubber tube getting worst?

[@0duvall0]

Hi there great video. When you changed out the black solenoid there in a spring and little black sleeve behind it. What is that sleeve called? I’m looking for one because mine is missing. I’m putting together a valve body that someone else started. Any idea what the part is called or where I might be able to find one. I’ve research can find it. I appreciate any help you can give

[@rickardomoses120]

thank you

[@JTAloft]

Awesome videos thanks mate! Question though followed your advice on replacing bridge seal and the 4 tube seals on my zf6hp26x in my 2004 e53 X5. I am still getting the hard downshift from 2 to 1 though. Funnily it is slightly better when in sport mode. Not replaced solenoids yet. I will do that though. Any other suggestions as to what could cause the hard shift from 2to 1 other than the mechatronics seals? Thanks.

[@dancsy]

Hey Julian. I have a E60 530i and got the same issue of hard shifting from 2nd to 1st gear and the problem is not as severe when sport mode is engaged. I've researched and found that replacing the shift solenoids is pretty much the only way to eliminate this problem.

[@StormxRaiden]

Love your channel. Will this cause the not to start also?

[@RobertMoto10]

do you recommend changing the seals under the mechatronic at each oil change?

[@csleeut]

My E53 when coasting down hill and shifting from 2nd to 3rd it gives a jolt. However if I keep foot on gas to keep rpm up,.it doesn't jolts. Any ideas?

[@brunooliveiramazza]

Jason, nice video. Tks for the content. How much would you charge for this service on a BMW 323 2007? Tks!

[@Vash16xli]

I've been thinking about something when it comes to my car and this video. I don't think I changed the black solenoid on my valvebody. Could that be the source of my electronic gear shifter not being recognized by my transmission? Every other solenoid got changed except that one, the seals were replaced (one was broken)and the fluid was also replaced. My car will not shift out of park though.

[@friguy4444]

Just awesome.

[@e065206]

Do you have a video (or recommendation) for how to remove the valve body from a 2003 Z4 (E85) with automatic trans. I believe I have the HP5. I have a code for a bad solenoid and hoping I don't need to remove the transmission to replace. Wondering if I can just replace solenoid in the car, or do I need to remove the valve body and then replace?

[@josecorredor2653]

I have a 6Hp-19 transmission on BMW 320 I, that the intercooler let the water on the oil, I replace the intercooler and wash it out oily water five times with chevron automatic transmission fluid and then use the same fluid, after about 40 miles the red warning light came on the dash board and lock the transmission in second gear. Did I damage some thing or what can I do?

[@mustafaaras2694]

Hi, thanks for your effort. I have a question. I have 2008 bmw 535i with 100k miles. My car has hard shifting issue if i drive slow. It is like car does not want to shift up. Gears are shifting little slippery to go up. Sometimes it is having same issue while downshifting. Gearbox shift well if i drive aggressive. There is no code. I have full system diagnostic tool for Bmw. I will change fluid but thinking about to change solenoids and sleeves. What do you guys think and advise? Thank you.

[@marchufields8935]

Hi I have a zf6hp26 I believe for an Hyundai Genesis 4.6. Curious if you ever encountered a click sound coming from transmission when gears shift ?

[@Blazekenick]

Hi thx 4 the tips! I've a question: t27 torque can you operate with oil pan, mechatrobic unit and solenoid or the size of nuts are different?

[@NLDMesa06]

I've got a 2007 328i touring RWD so I know I've got the GM gearbox. But should I still look at servicing the shift solenoids if I get the occasional shift issue? No codes are stored and fluid has been replaced.

[@thebluntchefosh6135]

I just bought a 2006 e90 last year it’s got about 236,000 KM on it like 170,000 miles or something and it’s starting to shift a bit rough I’ve been wanting to do this my fear is it’s never been done before and it’s too late to save shifting is not horrible but I’d like to get it sorted would you recommend a fluid change before this ?

[@f3414]

Hi I bought a 2008 330d yesterday, and 4th to 5th gear changes are rough under load, also in 5th gear under load the car jerks or wobbles as if it's struggling then in 6th gear it's fine ? do you think it could the the same issue replace the solenoids my local bmw specialist said it could be this

[@karlty7989]

I just changed ATF on my jag zf 6hp transmission hoping to get rid of my 3-4 shift problem. Its been a few hours but my mechanic says i should use it for a few weeks. I can shift manually through all the gears but have to ease off the pedal shifting into 4th. LAUNCH OBD2 shows that solenoid 4 is inactive. In still hoping for the best so i don't need to go through this. It's a 2009 but only have 38k km on it.

[@jdsfairlinetarga3790]

Are the things between the Metronics unit worth replacing. Little springs or seals? I have e clutch error but strange as didn't feel like it slips but just had a wobble

[@patricwell8335]

Hey how you doing. I watch your video and i was able to rebuilt my tranny successfully. Great video to learn from.. It been about 4 years now since i rebuilt it..for the past 6 months been sitting cuz i have to do a timing job..couple days now i keep getting code 48 for clutch lock up too much slip....i drop the fluid no metal no smell. But i do hear the tranny making a lil noise like torque converter...how should i test the converter or what should i be looking for...it drive good when its warm but 1st thru 2 gear it feel its struggling...any idea please

[@thanhhuynh6256]

Hi ! I have followed the DIY. I have change all the selenoids on 2004 E60 i also change all vales sleeve . The car starts up for me to fill up the oil. But next day the no crank no start. On the cluster all the light work , but except the Park, reverse, neutral, drive . Do you have any idea. Also i put the on reverse or drive car still can roll. Do you think machetronic position sensor fo bad.

[@NFSgamingEvo]

I just want to said thank you, I have a similar problem with mine jeep gc seems like they using similliar transmission, scanner said incorrect ratio speed ,people said I need to change the transmission, but I think the problem could be the solenoids or change the transmission oil , this is the code it trow p0731,thanks you I feel less stressed

[@georgemusiccovers]

So mine that park and unpark a little bit more difficult than normal and flashing an error of one gear maybe just have to change solenoids?

[@seskspalac]

i have problem with position lever sensor, so i can change only that or need to change all valve body?

[@flam7469]

Where did you get the kit from? I'm having a hard time finding all those parts.. even from the place you recommended last time.

[@magnibergsson7172]

Hey. I just change my transmission complete on my bmw E60. Do i need to program it to the new gearbox? It drive fine but not smootly

[@BehzadEghtesad]

can you find out which solenoid is for which job? need to know which one is torque converter ones? ?Tnx

[@joelmarquez9502]

Brother, what is the best thing to do with my BMW e46 323i 2000 model? Recently, I felt a delay shifting in second gear, then after 3 days it suddenly stopped, it almost didn’t won’t to move forward or backward, I would appreciate your immediate response.

[@carloscastilloveitia6837]

What are the part number for the solenoid kit for the transmission? Just bought the ZF Fluid and oil etc kit for a 2007 BMW 550i RWD…

[@xr500t]

Excellent. I just got a z4 and don't think there's any trans issues, but, I'm getting educated for when the time comes. So, you swear by Lifeguard? I'll defer to your advise. I've used Valvoline Max life on my Hondas(not the recommended fluid either) and has worked well for 400k! . With that said, I watched another guy swear by the Max life on other BMW's he's worked with. Anyway, regardless of my experience, I'll go with the Lifeguard. Good video, thanks for the info.

[@andrewduran9601]

Solenoid Kit - 6HP19/26/32 M-shift - is this my correct kit or this - Solenoid Kit - 6HP21/28 E-shift - for the 2008 528i e60?

[@andrewduran9601]

i have a 2008 bmw 528i e60 would this be the exactly mechtronics units? and instructions?

[@timdubya77]

I have a 09 528i. When I stop at a light or sign. Sometimes when I take off it rolls backs little like a manual. You think the issue is the fluid?

[@sugardaddy3145]

Hello which is the TCC Solenoid here? I currently changed the Whole kit as your video described and after a day I got a code P0741 TCC stuck off? Thanks

[@user-ro2ho5ll3q]

I’m getting a 507d code and the car will go in reverse and drive but as soon as it starts moving it jumps back into park. I just changed all sleeves with zf parts and added lifeguard fluid. Car still jumping in park. Do you think my problem is the solenoids

[@kirkyoung5627]

hello. my Brother im. a Big fan of your channel ... i have a prob ... so i have 3. 08 bmw x5 3.0... so i have a prob with 1. so truck trans goes into. limp mode. after driving for couple minutes... i changed the salonoids. and bridge seals but still having thw same prob

[@A13tech]

Im wondering... why the solenoids break in a first place ? how do they look inside ? Solenoid is in principle very simple device. Couldnt be reason of their "failure" be only some oring for 10cents ?

[@gmzysq]

Hello every one. I have 2010 BMW 550i M-Sport 4,8L with 6HP26 transmission. I have two code 4F8F and 4F81. Replacement bridge seal and 4 sleeves make better drive feelings but not for long. After accelerate up the hill road codes come back and limb mode ON again. Any idea what to do? Thing to change all solenoids but it is no solenoids error code.

[@jbleach23]

I have an Hyundai Genesis with a zf 6hp26 will the same software work for resetting

[@inganmarcelo]

anyone know where to get the six t27 bolt that is holding the hydraulic and the electronic(black plastic) unit together? the spec was to tighten to 6nm but mine just twisted in the middle and broke. I think is m5x55 but not sure anyone has the part number to original zf bolts.

[@joelmarquez9502]

And can I buy online solenoids plus harness like you replaced in this video and how much thanks brother

[@tlegg8745]

Were did you order the solenoids from i need to replace mines. Keep getting a p2761 code just wondering what could cause that?

[@reinaldoravicini9396]

Hi I have an 2008 X5 E70 and when your are driving suddenly she goes to Neutral when do a downshift (mostly 3rd to 2nd) , No error show even in BMW scan.... Solenoids may have no codes??? If you drive like a grandma, no problems at all...

[@abuzebain2]

Thank you🙏🌹🌹

[@havocprod]

Where did you buy the solenoids from ? I am particularly looking to buy only the green one, can.t find it as separate.

[@karlty7989]

Hi what kit did you use for that? My 2009 Jaguar XF 4.2L has 8 solenoids like that

[@anguscottman2804]

I’ve got an E70 that won’t shift into park. All other gears work. Any ideas?

[@darryl158]

Hi ya. I’ve got these codes coming up and it can’t recognise it’s in park. What do you think? P081C-62 Park Input Circuit - Signal Compare Failure P0915-01 Gearshift Position - Circuit Range/Performance - General Electrical Failure

[@adrianp4590]

have you ever fixed " Transmission failsafe activated. Possibility of redused acceleration. Have checked by the nearest BMW service " by just replacing the solenoids or is it usely something worse

[@angelocass24]

Hey i have a 2017 RR Sport and the mechanic wants me to change to entire valve body. should I listen to him or can I get a kit to change the solenoid?

[@kelvinmaduma1049]

Hi I have a jaguar s type 2003 model with a ZF gearbox which has a heavy take off n seems like it does not engage in other gears,how can I sort out the problem??thanks