Zortrax Inventure Desktop 3D Printer Review - Soluble Supports, HEPA Filter and Assisted Levelling

  Рет қаралды 1,083

Callum Coles

Callum Coles

Күн бұрын

Пікірлер
@theyvesloy
@theyvesloy 3 жыл бұрын
Thanks a lot! This is exactly the review I needed ☺️
@CallumColes
@CallumColes 3 жыл бұрын
You’re welcome, glad it was useful for you:)
@Test4697
@Test4697 2 жыл бұрын
Really nice review! Well done. Is it possible to share what needed calibration when you printed the bearing in the pre review video? Thanks again a lot for the honest review.
@CallumColes
@CallumColes 2 жыл бұрын
Thank you! Yes of course, so basically the bearing fused together slightly as there was not quite enough tolerance in the model to print with the default settings. So in the Z-Suite slicer, you are able to adjust some settings under the 'OFFSET' menu, 'CONTOUR OFFSET' and 'HOLES'. By tweaking those, I was able to effectively adjust the tolerance in the model so the bearing segments didn't fuse together.
@army310
@army310 3 жыл бұрын
good review and it looks good but on the high end side
@CallumColes
@CallumColes 3 жыл бұрын
Thanks for the comment, much appreciated! Yes it’s certainly a prosumer level printer, but I think anyone with a genuine need for more exotic materials would be very satisfied with this printer.
@sungyoon6376
@sungyoon6376 3 жыл бұрын
Thanks for a nice review. Have you experienced ‘build tray not seated properly’ error at the beginning of printing? It keeps happening to me. Usually Works after resuming (and rechecking the tray), but quite annoying.
@CallumColes
@CallumColes 3 жыл бұрын
You're welcome, thank you for the comment! I haven't had that error no, but then again, I've never removed the build tray since I've had it... Have you tried contacting Zortrax support? Perhaps they can shed some more light. If all else fails, could always try a different built plate in case something is misaligned with your current one.
3D printers are worse than I thought. Time to do something about it!
19:02
Made with Layers (Thomas Sanladerer)
Рет қаралды 240 М.
I was DEAD WRONG about air quality
20:24
The Next Layer
Рет қаралды 202 М.
Smart Sigma Kid #funny #sigma
00:33
CRAZY GREAPA
Рет қаралды 39 МЛН
She made herself an ear of corn from his marmalade candies🌽🌽🌽
00:38
Valja & Maxim Family
Рет қаралды 17 МЛН
My Routine as a 3D Print Farmer
24:11
Samcraft
Рет қаралды 165 М.
How a 3DBenchy can tell where your 3D prints need improvement
12:23
Teaching Tech
Рет қаралды 896 М.
Zortrax Inventure | Unboxing | Dream 3D
9:40
Dream 3D
Рет қаралды 3,8 М.
Ultimate 3D Printer Tier List - 2024 with Sale Pricing
49:31
Nathan Builds Robots
Рет қаралды 22 М.
The 3D Printer I'd buy if I started over
12:56
Shop Nation
Рет қаралды 2,6 МЛН
I gave Etsy 3 months - this is what happened
13:01
The Swedish Maker
Рет қаралды 628 М.
Support material complete guide for 3D printing
19:37
Teaching Tech
Рет қаралды 154 М.
Best DIY filter for your 3D printer: solving 3d printing smell and fumes
7:31
3D Printing With Richard
Рет қаралды 107 М.
Super CREATIVE Things to 3D Print | Anycubic Kobra 3 Combo
13:22