ZRoadz Hood Hinge Brackets w/ OZ-USA Pods - Ram Rebel

[@ZROADZOffroadProducts]

Thank you for choosing ZROADZ and making this video! We are glad to see that the Hood Hinge brackets fit perfectly and it seems like an easy, bolt-on, no-drill install - just as we designed it!

[@WaterFowler41]

ZROADZ Offroad Products awesome fit, love the brackets!

[@julianhuitron2663]

Would this fit a mustang??? 😈😆

[@sunj8286]

Do you have anything fit 2018 Rebel ?

[@WaterFowler41]

They do, check out their site, they have a few different options

[@GetmeoutofDelco]

Can you mount bigger then 3 inch pods if only mounting 1 pod not 2?

[@esterdory]

Thank you for putting together this great installation video for us! Very detailed and helpful!

[@HammerdownMotorsportsUSA]

Good vid those lights should help spot those deer for sure

[@menoob7878]

Great video, but I have a question. Does the lights come with a remote that you can press?

[@WaterFowler41]

Yes, I control my aux lights with my AUXBEAM controller

[@chamakese55]

I just put the bracket in between, felt like i had more clearance. Christmas tree zip tie and run along the back of engine, they way the older models had the hood light wiring

[@WaterFowler41]

Doesn't that push your hood up a bit messing with the alignment along the fenders?

[@chamakese55]

@WaterFowler41 nope. Just gotta realign the hood and lower the knobs front. Idk I just went that route to have more room for the pods to sit a bit higher.

[@Barrettzzz]

Do you know if the brackets will work for a 2022 rebel?

[@WaterFowler41]

Same exact truck so yes they will work

[@alanturton3394]

So I'm sold on the zroadz brackets, but thinking I will marry them with Rigid LED pods .

[@freedom_foz_6337]

Love your truck man!

[@WaterFowler41]

Thanks 👍

[@Joe-jd9yq]

How bright are they, I don’t think you mentioned the lumens in the video.

[@WaterFowler41]

I am not sure I changed out my pods a few times since this video. I'm now running Diode Dynamics SS3 max pods. BY far my favorite set up to date.

[@mcconicocj1982]

Water Fowler 41 is there any way to route a cable through the firewall on a 2021 Ram rebel? I have hood mounted led pod ditch lights, I'm trying to figure out how to run the switch cable through the firewall to reach the inside of my cabin, any idea?

[@WaterFowler41]

Yup, watch this video. I route a cable through the firewall on my dads limited. kzbin.info/www/bejne/jZ_NdXmOjsutY8U

[@johnd9267]

Looking for little help here I’m having a huge BITCH of a time getting through the grommet in the Fire Wall any assistance to how you got in and out

[@WaterFowler41]

Use a piece of solid wire or a kabob stick to pierce the grommet

[@johnd9267]

@@WaterFowler41 figured it out thanks for the reply back I moved the corner over on the Grommet holding the E-Brake cable. Then the switch cable slide through no issues Thing was really starting to piss me off

[@steveblanar5408]

Do you notice the bracket contacting the cowl much? I feel like my z-roads brackets aren’t bent enough...🤔

[@WaterFowler41]

No I don’t think they do, I’ll check though, have you checked with Zroadz?

[@WorkPlayDrive]

Thank you for the detailed video! Answered all my questions regarding hood clearance. The trigger controller has my interest. How reliable is it with the Wireless connection?

[@WaterFowler41]

Never had an issue. I was not expecting this thing to perform as well as it dis

[@redtunadventures5183]

Did you use a relay harness? If so, how did you connect the switch cable to your trigger? Or if not did you just combine those 2 ditch lights together and connected to your trigger? Thanks

[@WaterFowler41]

The trigger is my relay harness so it was as simple as plugging them into one of the trigger’s 4 channels.

[@tamadrums001]

Hey do you think KC Flex Era 4’s would work with those brackets and still be able to operate the hood as normal? The KC’s measure: W - 5.0" x H - 5.0" x D - 3.27"

[@WaterFowler41]

I believe they will but can’t say with 100% certainty.

[@ammarkazal]

Looks very good and high quality material do you have it for Rebel 2016?

[@WaterFowler41]

Yes they do make those brackets for the older Rams too

[@themaintenanceguy4559]

Did you find the hood lights to glare too much off the hood ?

[@WaterFowler41]

Some of the light hits the hood but nothing major, the brackets do a good job moving the lights to the outside of the truck.

[@yayadje9038]

Will these fit 2020 ram rebel as I was not sure what year is yours. Thx

[@WaterFowler41]

Mine is a 2020 as well

[@e1975surf]

does these fit baja designs xl-80?

[@WaterFowler41]

I can’t say for sure but I don’t see why not

[@e1975surf]

@@WaterFowler41 thanks for the quick reply...i am planning on buy a rebel and those are a must. plus the bumper light bar

[@pamoky5]

Looks like you have the exact same truck as I do down to the color, 2019? I noticed that your intake is on top of the motor with an exposed filter, is this a mod or how your motor came from the factory? My breather box sits over the right fender.

[@WaterFowler41]

That’s a vararam intake, a few videos back I installed it. Recently swapped it out for a Corsa intake.

[@capt512]

Great quality video, like and subscribe. Found you on fb ram page.

[@israellopez3999]

Muy bien

[@WaterFowler41]

Gracias!

[@julianhuitron2663]

Would this fit a mustang ???? 😈😆

[@ZROADZOffroadProducts]

We actually offer a universal panel clamp that you can use on your Mustang's hood. Here is the link for the mounting bracket: zroadz.com/i-23910180-universal-panel-clamp-led-bracket-to-mount-1-3-inch-led-pod-light-pn-z390001.html and for the cube LED: zroadz.com/i-23910193-3-inch-led-flood-beam-pod-light-pn-z30bc14w20.html

[@FishOutdoorColoradoAdventures]

To expensive for just bracket's

[@WaterFowler41]

Gotta pay to play

[@kentmillett1871]

The brackets are ok but not strong enough. There are better brackets and companies. SDHQ Motorsports in Gilbert, AZ built a far superior bracket. Mounting is similar. Good vidio though. I have the BD pro series high speed spots.

[@WaterFowler41]

I had sdhq brackets on my gmc, check out the video on my channel, they needed a lot of grinding to fit the right way. I’ve never once had any issues with my zroadz brackets where I wished they were stronger. LED pods aren’t that heavy.

[@kentmillett1871]

@@WaterFowler41 the BD pro high speed spots are heavier. I'm interested in your channel. Though I had no problem with my install. The BD had locking bolts to prevent theft. I look forward to seeing your videos. Thanks

[@idontcaresapo8233]

Bro how do you like the air filter? Did you notice any power and sound gains? Also what brand it is?

[@WaterFowler41]

Love it, gives the truck a nice growl and sets me up for some future tuning!