I just switched to a different shop and they don’t use the pps system they only use the sem vcs system and 3m performance tips. Super annoying now my 3m accuspray gun is useless I got to buy this gun now getting so fucking sick of buying tools (I’m a bodyman)

Great video thanks for the help

Good job thanks

Awesome job!!

It really laid the paint down smooth. Great job Mario ! I’m going to get 1 ! Thks !!😁

You're an acura tech, i was like where do you get the acura branded rust penetrant. Going to pick some Ospho up at Ace hardware! Much better then rip of on Amazon

GOOD VIDEO, HOW DO YOU COMPARE THE PORPHIS PRD VS 717 TO THE PRO 88?❤

Hey Mario, beautiful finish from the Master Pro gun it lays both the base and the clear really flat and glassy👌I have a couple of clears like this one where you have to get a nice finish from the first coat so when using them I normally give it a bit longer on the flash times which should reduce the chances of runs🤔 I was using my PRD-717 split tip this morning on a flowcoat, it was a MS clear but I didn't like the way the Porphis atomised this clear, with it being a MS clear it needs 2 good wet coats but the gun struggled to get a wet coat down so I don't think the split tip liked atomising this clear, I was hoping for a great finish but I'm not sure what happened🤷‍♂🙄Happy new year to you and your family🙏👍John UK

LOVE my pro 88 bought it I believe 2 years ago, I broke the 1.3&4 tip so it was outta commission until I ordered the new 1.3 cap and tip kit it’s been 4 months since and I resprayed a blazer I painted with a pro lite and it came out MUCH better the flakes were noticeably more even then before and the clear laid down flawless other than a few nibs but that’s not the guns fault

The 44 is a little on the heavy side but it's a good gun for spraying the base and clear !

Great video!! I purchased this gun like 6months ago. I spray ppg water with it and it does a fantastic job!! The shop I work at is very high production and this gun holds up to every single thing I throw at it! I would highly recommend this gun to any professional painter!!! Also wanted to say I love all your videos!! Keep up the great content!

🎉 First view

Awesome good!! Outstanding!!

that's what the knobs are for. not always full wide open like you and the other guy always teach. not every gun spray the same with the same settings

Great lesson, Thank you.

T didn’t teach u this one 😂

Good prep 🇯🇲

BRILLIANT SHORT VIDEO MARIO HAPPY CHRISTMAS TO YOU AND YOUR LOVELY FAMILY 👪 ANDY😊

Ja Rastafara... Happy Holidays

⛄🎄 Merry Christmas Mario! 🎄☃️

Prep is KING 👑‼️

Can white paint have same glossy as black?

How do you know about the quality of this clear friend?Have you seen the paint jobs after 6 months to know how it looks?All jobs in the booth are super....after? Merry Christmas to you and your family 😊

The 🤴 👑

Thanks Brother!

Had my clear run yesterday,sprayed first coat and let get tacky,applyed second coat but didnt let it tack,went wet on wet and weather being cold,Got me a run,fixed it tgis morning and happy I didnt have to repaint.

Help me man I have clear that is impossible to lay smooth I do everything right, basecoat flat as it can get but it always has that orange peel that is just on border with smooth clear but when I overreduce it, it's phenomenal. Do you have any tips on thick clear that does not like to be sprayed dry.

I worked with a guy in a paint shop that said he had 20 experience but would pull cars in the paint booth after prepping it to blow it off and clean it And half the time that was after he back taped it. We called him predo, so the other guy could redo it.

Great demo on removing runs Mario, I often have problems removing them as I seem to cut through the surrounding clear before the run is removed but what you did here should be a big help, thanks for sharing👌 I hope you and your family have a great Christmas and enjoy the holiday🎅👍John UK

I don't know the level or quality of clear you sprayed but I started using a higher grade of clearcoat to eliminate runs to get a glass finish

bro, no tape. just put the whole thing in filler. its much more effecient. and it protects the suroundings better. tape will rip en is just shit....

What is your take on the 3M purple bottle, I use it as an all around compound ? I know the finer grit paper makes for polishing goes quicker but 2500 or the fine merca pads is what I use, but to be completely honest with you I don't do much wet sanding and polishing unless the customer ask for it to be car show quality.

I like to wrap my 800 on a small section of paint stick then wrap masking tape on each end for cutting a run down. The tape will keep the ends from digging and spreading the new scratches out further.

Could’ve flatted back and reapplied clear again right?

Looks good. Thanks for sharing your technique

great job! thank you for sharing

Every time i use that damn porphis 715 this happens to me.... damn gun too fast for me 😂

Man I wish you came out with this a month ago😂 repainted my car and had some runs…got some blemishes afterwards trying to fix them, but hey mistakes create future perfections! Thanks for vid Mario!!

Hello mister Mario can make a video for how to paint calipers?

Great job 👍

Great content as usual

Happy holidays

I've shot that clear before. I like that clear and you're right, you have to spray that clear with 2 full wet coats. It's quite a few clears that you have to shoot like that.

So great gloss

May you please do more videos on how to keep ‘the wet line’? Aka preventing dry spots. I know you did a video on a hood. But what some tricks to prevent dry spots on a whole car. This seems to be my biggest issue right now. I understand paint mixing, reducer, correct activator, temperature, gun tips, pressure etc. Just need to see how you attack the whole car when spraying. How you move around a car. Thanks

Do you use tape on your body lines?

Good idea actually you could have tac welded a few spots tho

Had that problem last week respraying some wheels. I used a heat lamp on the whole wheel. The heat gun in the winter months is a must.

About the silver mottle. What do you set your pressure at? Also spray distance? Thx

Thanks for the tip will try it next time