Beautiful work

Proper work-holding, stops & casters, offset reveals, clean as a Will Smith record… purposeful and gorgeous work! 🙌🦾🤙

Yes, great job and a lot of effort, but same problem as all the others. What if you want the disc, not the hole. All these jigs leave a 1/4 inch hole in the middle of the disc. There is an answer, bnd I have made one, but I am afraid I can't show you as I have no filming facility, sorry.

Wow! You make great tutorials. Thank you so much!

Excelente tus proyectos muy profesionales, todo bien prolijo con acabados y precisión de excelencia, es una pasión ver este Canal todo un lujo, Adelante Éxitos!!!!

8:45 OVER 300 🤡🤦‍♀ Crazy..... make i for half.... 🤷‍♀ ASSOZIAL IS ASSOZIAL!!!!

Beautiful.

pedro savi

Someone should mass produce the parts and see this as a kit.

You're a bloody genius! Super design and impressive workmanship.

Hi, it's a while ago since you uploaded this, but I'm wanting to make some drawers under my bench in the garage and I've seen your other multifunctional bench video where you used iron drawer slides, in this modular bench you just use grooves and wood only. Could you perhaps say something about the difference between the two, why you would choose either one or the other so that I can contemplate further which aproach will suit my needs? Great video's btw, you are clearly very talented and I learned a lot from them.

looks very nice but I just don't understand how the knife locks open without folding . I think it would be easy to have the blade close on you and now your minus a digit

What is the table top material?

Tout simplement superbe !!!je rêverais d avoir le même atelier !bonne continuation, merci

Bonjour, quelle lame utilisez vous et quelle épaisseur de bois dur pouvez couper ? Cordialement.

Buy link for the diamond disc ? 🤔

bonjour le dessus de l'établi est fait avec quel matériaux merci

Comment 1,000!

Incredible design. I just cut all the pieces for my bench, all repeatable cuts with my table and miter saw with stops. Even then, it’s very hard to be laser perfect with each measured piece. So I have some instances where there are 1mm or less overhangs or gaps when assembling the frame. Is this something you encountered? What’s the solve? Wood filler and sanding where needed? Thanks so much! I bought your plans and very excited to keep going

This is fantastic. Do you need to completely remove the back to change the upper filter though?

This is amazingly ridiculous in the most wonderful way. I appreciate the way your mind works pal.

Wow, I am a newbie at Woodworking, but I am really impressed with that work table. GREAT Job!

Incredible, thank you

Great job! You are also music instrument restorer or builder?

Are the plans still relevant to this video - interested in purchasing them and making this :)

Has anyone tried this in North America? How much time and cost roughly? Appreciate the input. And yes, it’s a work of art and by far the best I’ve come across or seen.

Good heavens, man. This is next level stuff! I don't know how i missed this video when it was released. I watch all of them usually. Amazing...

Hello, your work is very impressive. I would buy your plans for this workbench except for the fact my garage requires me to have a work bench that abuts and runs along a wall length way. I need a table saw facing along the wall from right to left and not facing into the wall as this plan dictates. My space is limited. I would build your module bench to run off the left end of the main work bench, (or far end away from the table saw), and I would build the outlay table to extend out to the left from the table saw. The router table section of the bench would place between the table saw and the module bench. What are the chances you have plans? Are you able to help? May I hear back? Kind regards. TD

clever boy

Nice! Love your shop! My sister-in-law lives in A Coruña

I'm not entirely sure what the purpose of the silver t-slot is on the top of the jig. Is it for a hold down of some sort?

Bravo bravissimo, forte fortissimo!!!

Non avrei modificato il sistema di azionamento verticale Bosch, anche se devi farti i miei complimenti. Avrei realizzato un sistema fisso sotto il piano di sollevamento su guide e boccole con vite di sollevamento con un sistema cilindrico di abbraccio del motore: sganci il motore e lo infili nel suo sistema di sollevamento portatile originale. Saluti.

Your work is immaculate. I feel like if I could master your your level of precision in building jigs and work pieces, it would greatly improve my efficiency in the shop. Also, I don't know where to access the types of material you use.

Merci ou acheter tout le petit matériel ?

Using the drawer slide as a rip sled extension is next level!

Và vlx vlxx

youve been so detailed and helpful. yay for coming across your channel!

Mit Abstand das Beste und Funktionalste was ich je gesehen habe! 👍👍👍

You have very good design and build videos. Thanks for sharing!

Заклёпки-заподлицо.На первую трубку-одеть трубку большего диаметра с разрезом.При повороте будет работать как стопор лезвия,как у Опинеля.

got it, I'll get someone else to do it

outstanding !!!

He intentado descargar los planos y no me los envía a mí correo electrónico, pero si aparecen los dos cargos a mi cuenta bancaria, espero me brinden su apoyo para que me cancelen uno de los dos pagos y que me envíen a mi correo electrónico los planos en español. Agradezco de antemano su apoyo

I like your Clamp-Racks . . . Chris . . . From Norwich, England

Can I build it using mdf? Or chipboard?

Any chance you will be selling these insert plates?

salz als gleitmittel - unglaublich aber genial!

Muchísimas gracias por compartir Y FUNDAMENTAL LA TRADUCCIÓN!!!!! MUCHÍSIMAS GRACIAS! MUY FELIZ AÑO!! ABRAZO GRANDOTE DESDE ARGENTINA!

Another excellent instructional video. This is my second video I watched. I was already subbed on the first one! Thank you so much for sharing your precious knowledge and experience.