I added labelling as a condition to purchase after my inspection. I made the purchase conditional on a satisfactory inspection. Not sure if you can do that where you live.

my problem is the hole those latch arms go into, the thing in there that receives. its spring loaded i guess, and it popped up. Best way i can describe it, the door was being softly closed, which triggered it to spring up, but the door fell back a cm, so the receiver thing popped up inside without being able to grab the latch arm.

Thank you! Saved me.

It’s very important to mention that the valve has 2 letters on the side H. AND C for the hot and cold water so is a must to remember how you removed the valve. Also is very convenient to use a screw driver with magnet to prevent to drop the screw

Perfect! I had the same problem and this worked! Thank you!!! 😊

I have this exact model at work. Apartment maintenance tech here. Instead of replacing the whole control board, if you have a soldering kit, you can replace the transistor for the bulb. They usually run around $0.75 a piece and take no longer than 30-45 to do.

I got a ring pro 3 doorbell hard wired, noticed after about a year and a half I started to have to charge with the USB cord. Do these batteries go bad after awhile and need to be replaced? I have power from the transformer just seems the trickle charger is not working. Any thoughts?

I plug a radio into the outlet, when it goes off, you located the circuit.

When I put my Allen key in there it won’t move do you know if there is a fix to that problem I’m assuming it’s stuck because something is in there

5 videos later, you fix my garbage disposal. Thank you very much. It was the broom.

Billy Bob Thornton ! I bet you get people telling you that a lot.

Very thorough video…good job 👍🏼👏🏼

Meh, it's only (and I'm being generous here) about 60% accurate. I have used this tool a lot over the last 3 years doing facilities maintenance, and can testify it's absolutely wrong at least 40% of the time. Whether plugged in or otherwise.

What are those extra wires that come in the kit?

HOLYB CRAP DUDE! Thank you so much. Next beer’s on me brother.

👊😎

Great video!! I know that the parts can be found to replace. However, does GE sell the transmission with the parts included? I could only find parts separately. Thanks for sharing.

Why would anyone put their electrical service outside?

I have a quicker way, I short the outlet then go see which breaker tripped, much faster.

Thanks a million - helped me unjam after wife accidentally dropped a glass shot. Much appreciated

bro doing to much for the vacuum

Put the number 17 on the receptacle cover plate as well.

plug in a radio. when you turn off the correct breaker the music stops

Cannot use flexible foil venting.

After cutting the screen it kinda looked like shit. Do you think a metal ruler would help?

I worked in telecommunications and we have used toners and locators for a long time. I was wondering when someone would finally invent one for electrical circuits. The toner for an electrical circuit must be a bit more sophisticated, since all of the neutrals and grounds are tied together at the service panel.

The drill trick worked great for me. Great quick info. You deserve a follow sir.

Welp, I hear a light thump from the back, not the belt. Although. Wish me luck.

I assume ceiling light procedure is the same as the smoke detector wiring?

I did it...ty so so🎉🎉 much

Thanks! It worked & I used the water bottle trick to make the water go down.. saved me some $$

Hi Dave, greetings from Chile; really like your video, i'm just about to star building a shed with my dad and your content is really usefull for us right now.

As a residential electrician with 25 years in the trade, I can say this method of finding out what breaker services what circuit is not very accurate. A much better and cheaper way is to just use the plug tester and an extension cord. 100% accurate. You have to walk back to move the plug tester anyway. Start by turning off all the breakers. Choose a plug and insert the extension cord. Then go back and put the plug tester into the end of the cord. Turn on breakers on at a time until you see power. That will be your breaker you are looking for. If you really want to see what plugs and lights are on that circuit, you can test for more active plugs. Move the extension cord to another plug that has no power. Go back to the panel turn off the now identified breaker and repeat first step until you have marked all the breakers. Two pole breakers are easier to find the equipment they feed. Save yourself the cost of the expensive other tool, plus when you are done you know 100% exactly what breaker does what.

Were can i find the paet number ?? I havent had a dryer since last winter .2wks ago i found one .finaally won the battle it dought hard not to get in house. Got it running and hooked up.to find out the last load i did must have broke the washer .i literally want to cry ..ok whine done ive got to find this part number .thanks you so much for thw to the point vid .your a life saver thanks for alll do do

how much you can charge for that job..? $$$$

Literally a perfect video, clear straightforward help, multiple options, great content! Subscribed

Thank you so much!

I looked at 10 videos before finding this one and it is the best explanation and footage of how to remove and put the door on. Thank you!

Easier nowadays with cellphones- if you have two people and a plug in lamp

You literally just saved me some unknown Mega-plumber bill-thank you.

My dumb self was just hauling on it trying to spin it… thank god I found this. Thankyou sir!

Thanks for your vids! I've had one for a few years now and I think it's great. Batteries on mine last about 3-4 months but others may vary. I sat to install mine and I should have been standing when I programmed the finger print. The angle is a little off so one of these days I'll reprogram it. If I've been out in the rain it seems to work fine if the batteries are fresh but when the batteries are a little low I have to dry my thumb for it to open.

Crona Lane

Got the bitch unstuck. It was a clamp U-ring from a damn Nalgene bottle cap! It was so stuck on the side of the chewing disc, I couldn't pop it up with my longest screwdriver. It ended up getting popped down, and I believe it's in my trap now. As long as it doesn't back up the sink, I'm not messing with it. What a SOB. I needed a strong magnet to get it out 3 weeks ago, but I didn't have one.

I used this video and fixed my problem! My wife thinks my a masculine chad now ;)

I had a aneurism seeing him drill through the cabinet and staple the hot water line to the baseboard…. People he hooks it right but this is the guy your shady uncle says we’ll he can do it cheaper… open up your drywall, split your hot water line like a man (pex is eassssy, copper not so much) and then install the hot water valve next to your cold valve and make it look nice. People don’t drill holes in your pricey vanity and then proceed to cable staple it to the trim. This will decrease your home value significantly. If you went somewhere and saw that you’d know it was the jankiest shot you’ve ever seen and can’t guarantee anyyy of the plumbing underneath the surface……..

What is the rebar for?

This is Optional I think I mean how many times are you going to have or need the dryer door opened when wet clothes are being dried.. I mean when my dryer stops when the drying cycle is complete the dryer still shuts it's self off.

Thanks buddy. I’ve been waiting on maintenance for seven days. My house reeks smells like rotten eggs. This method worked!!! Now I can have girls come over again 😂

Thank you for this!!!