Thank you so much for this video! I’ve been wanting to get the hard drive out since my iMac died, and this was extremely helpful!

Mine has the same problem. Took it apart, and found there is corrosion and rust around the motor. Looks like the rubber seal at the top failed. It's amazing the thing actually even still turns on. Don't think there is any fixing this, especially since it's probably at least 5 years old. Sucks though.

Thank you great video just what I was looking for.

Just get to the darn point. 🥱 @2:17 And he's going to completely skip filming a couple of key steps. 🤦🏻‍♂

That tiny little M2 screw at the front by the brush attachment often comes loose from use and the toothbrush becomes noisy and the brush will not vibrate. Clean the threads, use plenty of RED LocTite on those threads, re-tighten and reassemble. You should be good to go.

So the brass piece was really gunked up, no issues with the spring shooting it up, couldn’t barely get it out and in my attempts to do so, I broke the tip of the white plastic piece that actuates the pressure switch 🥴. I can’t seem to find a replacement online, all the parts guides have everything but these. Do you have any recommendations where to get a replacement?

Have this same one for my 2009 Dodge Ram 1500 … some of the other videos say there for a 2009 but they did not have the same key fab as me so users who are trying to learn try some other videos also but yours is the best

I’m going back in a little 🎉 And I’m so happy for the people in

Hola tengo un problema com la hidrolavadora ryobi de 2000 psi. El swiches del automático no me funciona q debo hacer hay lo desarmado varias veces. Y no acciona el swiches

what is cycling names pls😢

Alexa in it?

Thanks, was able to diagnose a broken GFCI plug because of this. Power washer back up and running!

Never mind I subscribed

I’m sorry I can’t figure out how to subscribe

Why did yours just pop right out?? Mine was really stuck in there. I use tapping it and pulling it. But that pop broke on me.

Thanks for going to the effort of uploading.a followup. This is really valuable to me so I can set my expectations appropriately. Thanks!

At about the 58 second mark, do you know the name for that brass piece with the white plastic that triggers the switch? Having tried every path but finding them unclogged, I removed that part and now need a replacement as re-installing it requires the strength of Hercules to suppress that spring and secure it with the pin. Doing so damaged that brass piece.

Old is gold. I had a very old pressure washer I used every year without a single issue, now that is gone new ones fail every year for different reasons. Thanks for your insight.

Thanks!! Your video helped a lot!

Could you instead run vinegar through the system and have it self clean so you don’t have to take it apart?

I love all the soothing lights on this bathroom fan with built in speakers.

thanks great video. I took it apart, and SHOULD NOT HAVE, it was working fine. Broke the O-RING which is size. id=5/8. od=3/4. thickness=1/16. can buy 100 for $4 from amazon, but will try local hardware store 1 for $2. lesson learned leave alone what is working. trying to solve low pressure. it is a great pressure washer, will run forever when lubricated properly IF I CAN FIX low pressure. Will take pump apart next to see what I have. By low pressure, I mean maybe 400-600psi, and not 2,000 psi as expected. Any thoughts appreciated by viewers. ANYONE KNOW EFFECT OF O-RING being old cruddy and not working properly. If anyone knows, a reply would be great.

Do you think it could be a short circuit for charging? kzbin.infowpUdDw6S9x4?si=DiaLym0r2XDzqaoL

The inside looks like a lightsaber

I know this is old, but THANK YOU! I ironed 2 blouses last night, but today iron doesn't work. I got stuck after removing the first 3 screws and your vid was the first response to my Google search. Hamilton Beach/Proctor-Silex I1309

I have a electric pressure washer that keeps stopping and starting with the trigger not pressed what could it be. I checked everything that you mentioned but it still does it, goes on and off. What does the mechanism look like on the high pressure side where the water comes out I'm not sure if I have trouble in there. I can't find any diagrams of exploded view. Any help would be very appreciated.

The plastic has gunk or the spring is compressed and not allowing the plastic arm to move

Thank you so much. This video helped me remove my old imac 2009 hard drive and save precious photos and music using a hard drive reader. Again, thank you.

Wonderful tutorial. I will try this on my next project

I can’t get the core tabs to release. Any advice?

great job on the update and install on the replacement. thanks!!

Thank you for your video I have the same issues

Would this work with a hairdryer? What is the temperature of a heat gun? Sorry newbie here.

Mine turned out to be the power supply plug. Easy enough fix.

That's so stupid. Why don't you show the only part we need to know.i can't get that core out

Hi, Thank you so much for this video. At an authorized repair center they said to me that they cannot repair this kind of toothbrush... 20 minutes with your video and I fixed it on my own :) Greetings from Warsaw / Poland

5 years in and you are still helping people. Just cleaned the valve and put new washers in and works like a charm now. Thanks!

Cool as ****. Great build and looks amazing. Thanks for sharing.

Thank you.

This pump and switch is exactly like the Craftsman 1900psi washer. I wish I had seen this before I did all the things you said not to do. My spring and assembly went flying. 🤣🤬. Nothing really looked dirty, put back together, and it still cuts off and doesn't come back on. Also, you didn't mention, but there is another small o-ring that goes up in the switch housing on the white pin isn't there? Placed on top of the small hole washer before putting the switch on the valve.

Thank you so much. I accidentally dropped my Sonicare and it stopped working properly. I followed your instructions and it took me half an hour to fix my toothbrush which ultimately saved me from spending 130€!

I did everything you did no problem. But still no go.😢 is it possible the gap is too big? I did 2 shims just as you did The only difference is mine wont even hum. I put it on charger and when i take it off it lights up but nothing happenes at all when i push the button Darn. I was so sure it was gonna work. Good video in spite of my result.

Worked beautifully. Thank you!

DO NOT THROW IT AWAY UNTIL YOU CHECK THIS. If both green lights are on and it won’t turn on It’s very easy to check the brushes and armature on the motor . Clean them up with emery cloth. Make sure you orient brushes the exact way they came out to maintain the wear pattern. Mine fired up 😮

Nice video man. Thanks a lot

I tried this and it didn't work for me; the brass part was all rough and scarred some. I suspect it's causing a small pressure leak preventing it from being able to overcome the spring's tension. I can't find a replacement either so guess this thing is junk now :( I have a LOT of Ryobi tools. Some are great, others are not. Mostly their brushless battery power tools are good; not all but most. Their other stuff is hit or miss; for example the battery powered dremel is junk it has no power. But the small 80W inverter is good and the fan and lights are great. Guess their pressure washers are on the junk list, mainly cause there's no replacement parts for these valves and the pumps.

thank you so much, it works just fine.

I use a Q-Tip to clean out.

Does anyone know the correct oring size to replace the one he presses the white plastic piece past?

Stopped watching when you hooked the chain up like that. Hopefully nobody learned that technique from this video.