I'm about to pull the engine out of a 2012 Tucson and do a complete overhaul on it then reinstall wish me luck

Will be doing this on a 16 chrysler 200 soon. Any idea if new engine needs any sort of programming after installation?

I truly dig how you were removing the Alternator cable BEFORE you removed the battery!

Are you supposed to use some blue loctite on these bolts? I had to reinstall the 4eat transmission in my 2.5L subaru, and I put these bolts in fairly tight when I reinstalled the transmission, but like a month later the engine had to come out, and when I went to take out the torque converter bolts, two of the four were loose! And I KNOW for sure I tightened all four.

at 4:10 is that where you crank the engine by hand on these engines? where you took that belt off?

I will say this good job but you made this job harder than it was suppose to be

Some talking would of been nice...

Actually seems like a pretty well thought out setup, doing a clutch on one of these today. great vid edit: took 5-6 hours, pretty well thought out design

Can you remove the Hybrid system and replace it with a transmission from a non-hybrid car? I'm sure the PCM and TCM would need to be replaced/reprogrammed. Just wondering if it's a cheaper alternative to keep these cars going longer.

Great thank you

Anybody on here from Mississippi

Why no volume

How many labor hours 😢

gracias exelente video fue de mucha informacion y muchos detalles

I have no sound but l can see why you are replacing this 2015 Hyundai engine how horrible are Kias and Hyundai's there are so many you tube videos to do with Hyundai and Kia engines none of them good they absolute piles of junk well my 1997 Toyota Hilux with 437000 kilometres on it is perfectly fine and probably will never have to be replaced at least for another 27 years

Sir thank you very much for this video I didn’t know how to access the bolts that on the flex plate

How did you remove the transmission from the engine

Hey I know this is an old post but I had at question. At -23:10 minutes, what is that cable you are pulling out from the top? Looks like you just use a screwdriver to unhook it

What is the best battery ratchet to use

👍👍👍👍

Great and excellent video 💪🏾👍🏽

service that ptu lol

Are 2013 and 2016 similar in this process are there any major differences that you are aware of?

My 2013 altima is at AAMCO right now getting the transmission replaced. Now i know why it is so expensive. Thanks

Just straight to the point video no talking,

Is there better way to lift it up from top ?

I was wondering if this is the same as a 2018 Ford Fusion 2.5?

Can a 5.7 l small replace the 2.0 engine in these cars?

Did you have to unbolt the torque converter before pulling the motor

Great Video. Do you have to pull the exhaust system?

Hi, I'm just curious. What part of Ohio are you in? Do you work on Toyota's?

how do you remember where all the screws go?

I think, just buy a new car.The time u spend in dismantling, then repairing, then re installing, do u even make minimum wage?

It’s been 4 years, I understand. But however, I’m in the middle of an engine replacement in a 2015 Durango with the 3.6. New engine is in, but I can’t get the torque converter to spin around freely to line up with the flex plate bolt holes. Did you have this problem?

Where are you from?

I didn't see an engine bar holding up the engine or a jack below. I also only saw onr motor mount. How is this engine hanging? Lol

Just found out my transmission is going to need replacement. How many book hours should i expect it to take?

What state are u in?

What are all of the major parts you had to remove in order to remove the engine? Btw love the video but I wish you could have mentioned each step as you worked

How many bellhouse bolts should it be

What’s the star socket called? And what size is it?

I this time lapsed ??? 39 mins. Is AWESOME !!!

Is there a difference between a transmission with a plastic valve body pan and a metal valve body pan? Will a transmission with a plastic body pan fit a hyundai that had a metal body pan?

That fuckin Matco puts in work gawd damn

Help. 2006 mazda 5, i got the transmission installed and when into tighten the trans ti engine bolts i can bearly trun the engine over.

I'm getting this done right now to my car had 130,000 miles on it and the only reason why they're doing it for free is because I got all oil changes done the dealership

CAN I REPLACE A 4 cylinder EQUINOX with a V6 ENGINE?

That was awessome, you are the Master !!

Dude the video is on point you are an awesome tech