i need help. i get message when open bmw scanner, that device drivers are not installed? how to fix it?

Egitici, ogretici. problemin cozumunu paylasirken ayni zamanda problemi nasil cozebilecegimizi gosterdiginiz icin cok tesekkur ederim. sevgiler

Excellent Video detailing general architecture and adressing all possible causes of failure (including antenna)

Thanks, this vid saved me a fair bundle. Had some expensive quotes for repair so decided to have a go myself. Pretty sure it was a poor connection on the reciever as after checking power as per your instructions it all worked again after re-initialising keys. Thanks again !!

Thank you for the video!!

Hello! My car has a problem: 65 NW_E- Fehler. I took out the sensor and measured 12v and 5v.It's OK! If I bring iron closer, 5v decreases. At this point I start to hear some engine mechanisms buzzing. Is this normal? Can I be sure that the sensor is working properly?

Hello, this does not work in Win11. I am able to install the drivers in device manager as you show with the file you link to. However, when I open the app I still get the message, Device drivers are not installed. Please help.

Such a great video

nice bro but which coolant please add part number or links cmon

Would the amplifier cause the key fob to not work as well as when you put the key in the door the locks do not work, nor does the center lock button? I have replaced my key fob when i lost it from the dealership not even a year ago so i don't think my fob is bad

Just did the replacement. The key with the battery swap lock button doesn’t work anymore. Can unlock and open trunk but can’t lock the car.

Mine does It also in release and acceleration at low rpm. I am currently using 10W40, i checked timing because i Wasn't sure what problem was, and the car currently has 27° of timing instead of 20°, but the noise the car makes Is exactly what yours Is doing.

any idea if it's possible to disable corner lights on automatic setting? EU E46

Nicely made video

Headliner cloth repair time Lol

Hello hope you can help me I know it’s an old upload but I’ve done as you have shown everything works as it showed but when I try to adjust driver side mirror for down and right it folds the mirrors what could be wrong solders ? Or I re assembled it wrong?

Any Idea. In mine just show up. DME and EGS allow to read and see parameter but The rest of modules. Not found said Message. I try to figure out whats wrong. I couldn't find anything. Any help i will preciate .

Any chance you've done it on an E46 or E65? Are they identical? On more recent BMWs, you need to disassemble the mirror from its base which seems tricky with the huge spring

Best explication so far, congratulations

Very good video, well made and informative. As the owner of a M54B30 engined BMW that drinks oil at a alarming rate, I'm very interested in knowing if the use of Toralin to clean oil piston rings has helped to reduce the oil consumption.

,,device drivers are not installed" why ? and what i do to fix ? 😑

Hey, what kind of charger you use to charge key? I don't know where I can buy it, actually?

My scan tool told me the Right Side Inner sensor failed, I have a new one coming. This is a fantastic video, I can do this myself after seeing your clear instructions. Thank you so much

Excellent video! How do you identify these connectors? X1101, X10184, X10183 It's hard to see in the video what these connectors are.

請問鑰匙充電，是否可以用手機的無線充電器

Very first solution - key reset - in my case worked right away. I knew that key would be OK as it is less than 2 years old and this remote control problem started after my car battery went flat. Excellent. Thank you.

Would a code P1525 be related to this sensor? My car seems to be driving fine but this code just showed up.

Thats all well and good but what use is saying now get inside the car and pop the interior light off...etc...etc? If i had access to inside the car, i'd send it to a mechanic.. Im watching this precisely because i dont have access to inside the car.. The car wont unlock..

Do I have to use the air compressor and if not what do I do

Professional guide

Thanks lot for making this video, saved my day!

I have the chemical composition of GM Top Engine Cleaner. What is the composition of this product? Many of these products contain significant amounts of carrier oil. That oil likely increased the sealing ability of the compression rings, thus the increase of compression to 150+ psi.

Two tips: If you have trouble inserting the bolt that holds the tie rod, use your 10MM hex key to spin it until the notch lines up with the bolt hole. and it's VERY important to support your 17mm hex key when you're adding the 180* turn to stretch the axle bolt. I put a jack (or jack stand) right under the extension so that all your force is applied to turning, and not putting an angular force into your breaker bar, hex key or socket extension. It's pretty easy to break these with those kinds of forces. (see 5:58).

On some cars, the removed bolt is not long enough to reach the end of the stub axle, and so will not push the cv joint off. If this happens, you can insert a 4" long, 1/2" diameter steel rod into the cv joint. It will embed itself into the stub axle about 2", leaving the same amount protruding into the cv joint. This will give you the reach to seat the bolt against, making it easy to remove the cv. If your wheel bolt screws all the way into the cv joint, and the shoulder of the bolt is seated against the cv, and the cv does not release, this technique will work for you.

Hi, do this tool gone work on my Z4 E86 ?

Perfect. Great information. Thank you.

Thanks for this. Very informative and to the point.

This is intense 🥹 💀

One important piece of information you left out is that the rubber and the plastic bump stop tabs on the articulating arms have to be removed so that the boot can open an extra cm or two. If this is not done, the old struts are difficult to get out and the new ones almost impossible to get in.

Excellent video

Great video. So, the arrow direction is pointing to the back of the car and not the engine? Mine was installed the same way, but I’m confused because the flow direction (arrow) should be pointing towards the engine.

the pa soft still works with generic obd2 cable ?

Very smart I can’t do that very hard ❤

Excellent video. Have been driving the 525i touring with non-functional parking sensors for a while, time to get busy!

I was going to attempt a repair today until I tried buying the FOB battery. Nobody carries them. You have to buy them online. ie Ebay, Amazon, etc. I am on hold while I wait. My current FOB that just went dead is an '02 e39 540i Touring. My FOB did not respond to the re-pairing(?), the central lock in the center console does lock/un-lock everything correctly, but I have lost the ability to open the rear glass or rear hatch manually. Are there different fuses or modules to check in a Touring? Is this normal to lose functionality on the liftgate when the FOB goes dead? I have to crawl through the car to get to the emergency mechanical liftgate release to open the back, not fun.

Hello, could you help me? "S" is not a vaild integer value

wow, wow, wow, if only every video was as clear, informative, well filmed, information rich as this one, and KZbin would have 1/100 of the number of videos it currently has. Best instruction video ever!

Very clear, excellent video, thank you

Thanks dude!

What colour is wires for input signal,lock unlock