Where did you get the seal kit? I need to do mine. Thanks

Thank you for the information I'm going to work on mine it's working good but still going to work on it thanks again

Dear please help me, how doing in my Genie Z-45/25 when always the light Number 9 and 2 in the Start Module 56057 first is on, after 3 or 4 second off together lights, and off the engine, thank you Sr

DO you still have a video on switching the control pattern on a Komatsu PC150LC? I can’t find it on KZbin anymore and we are trying to do this on our machine. Thanks!

Hey Paul. Has anyone told you that your speech is hilariously close to forest gump. and I’m not trying to be a dick. Funny as hell though. If your girls name is Jenny we need that interaction !

gracias excelente video

Just a friendly suggestion: 1. If your a Mobile HEM, then you should invest in a HYDRAULIC IMPACT DRIVER. Stanley/Proto or HTC. ( these tools make removing gland nuts a simple, quick, safe, and injury free method.) Jumping on a pipe with hydraulic fluid residue is an invitation to the emergency room! 2. If you think that investment is too expensive, then how much money will you save when your unable to work because you severely injured yourself, broken limbs... or you get a hernia or worse, you kill yoursel trying to use your body as leverage. 3. Our physical strength is no equal to any Hydraulic Tools.

How much would you charge for a brake job on this Case

Looking at Case track loader what state are you in

Please keep making these videos. Great job!

How does the circuit board inside of the base know what position the hand controls in

Sir how many liter u pot on hy trans

Hola una consulta necesito el mandó final del bulldozer case 850 b

Hi, I've tried to update the software on Genie S-85 XC year 2018 (Bootloader 1302967-1.7.1 and Firmware 1302966-1.9.5) via USB. The Bootloader successfully installed and during updating of Firmware DISCON, PCON main, PCON secondary and TCON secondary successfully update 100% but TCON main not updating and showing message "Sub-ECU not responding try to recovery. I've checked wiring and CAN resistance on J5 and J10 connectors, all good. The Genie have ALC-600 controllers. Can you please help me. Thanks in advance.

Good job men good bless you I pull engine and transmission from automóvil but not from this machine thank you so much for share

Hello I have a 329D as well and after a rain storm the left joystick lost some of its functionality. Not completely dead like the one you are working on. Forward and back work fine. Left and right will work if you mike a very very small turns. I did the joystick test and when testing left or right axis the readings work and go up to maybe 25 or 30 but if you go any further the signal drops off and then the code is thrown. Left speed sensor or right speed sensor errors. My question for you is: Did the mechanicals in the joystick seem serviceable? I'm just wondering if I take it apart I might find a little water or rust in the mechanical side of the joystick. Anyway, thanks for the video it was really helpful and I'm about to have a heart attack if I have to buy a new joystick lol Thanks again! Wayne

I have one that it done want to move something it moves slow

I have a 580 super l series 2 that the transmission is popping In and out of gear is all 4 ranges any direction of what to check

Thank you for this video. Keep making these!

I have a 6036 and its leaking 😂 where the 2 hoses exits the boom side to the hard set of lines mounted to under the boom. Do you know if those hoses can be changed from rear of boom or if the boom has to come apart. In trying to understand i think they go to the tilt cylinder but the lines seem so tight in the boom. Any advice? Great videos thx

Hi, I don't know if you can help me. Would you be able to tell me how to factory reset a Genie s60, please

What part number did you use to get the striped down version joystick??

He went a few transmission services too long

Your video is so informative and easy to follow. My very first lift account I just bought an 1889 12,000 sq ft bldg in need of repair. My friend just retired from his construction biz and sold me his beast Genie S60. He would come over and show me things. Next trip was what’s behind the box. He passed away suddenly and now the lift does exactly the same thing: crank no start. So thank you much for explaining things the way he did: layman’s terms. Getting the close up views was a bonus as well.

Big LIKE! :)

You sound really unsure of yourself, so that’s probably why they didn’t let you do the transmission. Gotta know what you’re talking about then your customers have faith in you.

What kind of grease did you apply onto the rebuilt piston and gland?

Donde puedo conseguir el diagrama eléctrico

🎉 Oh my goodness, that dozer is about like the case 1150 I purchased. It missed alot of love. Best thing I found is 2 railroad ties and plywood and a floor jack to drop belly pans. My hydraulic system has been flushed several gallons of hydraulic oil from bad hydraulic lines and lots of filter and fluid replacement. I had filters as tough to get off as those fuel filters too

Doing a current engine swamp from Perkins to Deutz in S-65 2008 any experience/issues with doing this.

Great video! I have a jlg n40 e. You’ve helped me figure out how to work on it a lot. I still have some issues I’m trying to diagnose.

how much was this job i have same machine needs cylinders done so i know im not being ripped

you skipped the most importan the fill part

Good job 👍, but sir i really want to be like you on this job sir. What will i do? How will I get online training from you sir and what will it cost me sir?. Please sir I really need your response on this sir thanks.

This video was alot of help. I just lost power to my genie lift after a heavy rain. It ran fine then mid use 30 ft up it lost power. Someone sent 2x12 out 3rd story window to get me free.I'm gonna check my relay connectors like in this video and see if one is nasty. Thanks for the upload was a godsend .

This is so funny! My dad and I work together, his name is Paul, we only work on Skytraks! had to double take when i saw paul's equipment repair 😂 thought he had a whole secret youtube

I had a 2012 Lull with a Deere Power tech . Never would start when cold. Even either would not start?! Once warm no problem. Needs two 1000cca to start . Low voltage to ECM when crank was issue I was told .

Typical wait until transmission slips burns then change oil and filters.. Goofballs Clutch friction fragments means forward clutch pack roasted . See it so many times.

Where are ya buddy. No new vids?

I replaced the right hand a yr ago and it’s back out again I did the same thing u did they told me the same bs about the hole thing but why is it out again how do you Bypass the hydraulic safety lock I’m in bad place to be broke down

i enjoyed your videos out here in jamaica paul i have to go work on one of that same jlg tommorow i had hook up some head lights on it back up light and back up horn so now the guy called back saying battery not holding charge but it came with out here i think with that problem because we had to jump it of when we pick up at the port and also fallowing after driving it we jump it off again so tomorrow first thing check alternator charging because it been at the port for a few weeks and that sea frost is bad for it / thanks for the videos paul koooool

La mía no aplica que puede ser

Best way to make customers understand is to hit their pocket book

So like you I really like to look into a schematic and see how things work, but say the the machine is throwing tilt sensor codes or perhaps I familiar with a certain machine did my function tests and think the tilt sensor might be having a issue. I may look at the sensor and connector to see if anything looks off/not oem. Did this last week and noticed the seal on the tilt sensor was a bit pulled out, a pin was intermittently making connection due to being low. In this video example think you did the best thing, have wasted alot of time pulling on shit due to having no wiring diagram.

Good video it was very helpful! I have a question, only one cylinder from my machine goes up and it dosent go down the other cylinder dosent move at all it only stabalizes when i leave the machine off for 3 days what could the problem be? Thanks

Hi Paul. I have a leaking rotary and the local dealer tells me that I shouldn’t reseal it I should replace it. The cost is $3200 for a new one. Is it really that difficult to replace the seals? Do you have any recommendations where to buy used parts for a Genie? I appreciate you taking time to making the videos, very informative.

Using wire piercing probes can leave a place for corrosion to begin on the exposed copper. What do you do about the hole in the insulation after you're done testing each wire?

I never have the luxury of having wiring diagrams at my disposal so I'd be that guy going around checking grounds, power, fuses and relays. 99 percent of the time I can find the issue that way.

How did you know the timing belt was cracked and worn without inspecting it?

I'm surprised the owner didn't change the fluid and filter on his own before calling out a very expensive road mechanic. It looks like there was massive water intrusion into the case. Other than a missing dipstick or something; how would it get in there?