The New VW ID.4 GTX (Volkswagen)
7:08
How to replace a clutch and flywheel
7:25
Why You Need An Ultrasonic Cleaner
7:12
Пікірлер
@mih9915
@mih9915 7 сағат бұрын
Bro presses the Minute button 🤔🤔🤔🤔. Cmon 🫤
@stevenjeavons8665
@stevenjeavons8665 8 күн бұрын
to compliment this great video could you please add a section on how to set the gear lever when reinstalling, as this is causing me an absolute headache
@user-lq7mv5tq6i
@user-lq7mv5tq6i 15 күн бұрын
Mine takes the gears,but it's having a wild grinding noise, untill 5 gear
@PaulRogers-eq4ze
@PaulRogers-eq4ze 16 күн бұрын
Great video do you need to check the wheel alignment after doing this?
@Amritbhangal
@Amritbhangal 22 күн бұрын
Hi mate I followed this and replaced the complete gearbox with clutches in 2014 polo. Now when I try to start it’s always in gear no matter which gear I select . I even disconnected selector cable and moved the pin manually but it never goes in neutral or park always in gear. Please help
@ford873
@ford873 21 күн бұрын
From the way your talking it sounds like you have replaced a DSG box and not a manual box?
@MetjaBrightMatsimela-wv5tw
@MetjaBrightMatsimela-wv5tw Ай бұрын
Which part is the thermostat?
@lukasb5346
@lukasb5346 Ай бұрын
Hey! Amazing Video! BUT didnt you switched the rotating Plate below the the car - with that one side straight for the moving bar and the other slightly leaned angle one ?!
@PedroPlckle
@PedroPlckle Ай бұрын
THE go-to video on YouToob for making this replacement. I used both-thumb pressure only to push home each bush on the ends of the pivot lever rather than opt for the pliers. 🙂
@vuyo2178
@vuyo2178 Ай бұрын
Thank you ,
@ford873
@ford873 21 күн бұрын
You are welcome!
@montydiy4561
@montydiy4561 Ай бұрын
Hi, this is a great video well explained and have you done a video to remove an automatic gearbox. I have worked on cars but never replaced a clutch. I have a VW UP 2013 Automatic and the clutch is slipping. After watching your video I have started to remove the clutch. I have removed all the top bolts, a stater motor. I am unable to remove the bolt from the stater motor bell housing. I am not sure which wire looms/plugs to disconnect and how they are secured. Tomorrow I am going to remove the oil, drive shaft, and all the bottom bolts. Also which clutch should I buy, the listing says semi automatic or manual gearbox operated by a control unit. What oil would you recommend. Thanks
@somewhereontwowheels9363
@somewhereontwowheels9363 Ай бұрын
This is 4 years old but its been so helpful to read my VW diagram. I’m used to old motorcycle diagrams with no ECU. Thanks
@ford873
@ford873 21 күн бұрын
You're welcome!
@coolmonkey619
@coolmonkey619 2 ай бұрын
How much does the clutch weigh? 20kg or more
@xenolith5
@xenolith5 2 ай бұрын
Great video to come across, thanks. I know this was recorded a long time ago but are you able to describe which way round the collets go. My 5th gear disintegrated so the collets were loose. I can’t quite work out which way round they should go i.e. central dip facing inwards or outwards. Any help appreciated.
@NickPae-eu8mg
@NickPae-eu8mg 2 ай бұрын
Hello great video, what grease was applied?
@joanneadams3526
@joanneadams3526 2 ай бұрын
Thankyou it's a hire car and came with wrong time all sorted now 🎉🎉much appreciated ❤
@ford873
@ford873 21 күн бұрын
You’re welcome 😊
@TheChristopher1972
@TheChristopher1972 3 ай бұрын
How can I get the wiring diagram
@jopsonputhenpurackal
@jopsonputhenpurackal 3 ай бұрын
Do u know where is the gear oil filler bolt? Is it inside the starter motor housing
@bingxushi
@bingxushi 3 ай бұрын
Hello, is the mechanical structure of the amt and mt transmissions of Volkswagen up the same except for the gear selector and clutch
@ford873
@ford873 3 ай бұрын
Sorry I do not know.
@sammillis3989
@sammillis3989 3 ай бұрын
Hi there, do you need to program/calibrate the new throttle body or is it just plug and play? Thanks
@ford873
@ford873 3 ай бұрын
You need to carry out a basic setting. It will work without doing it, but will not run as well as it should and could potentially put a code in for no basic setting.
@elg308
@elg308 4 ай бұрын
Take a wheel barrow full of money when buying parts from vw
@HTaylor04
@HTaylor04 4 ай бұрын
Great video! Are you a company as my polo has done the same and I’d like to get it taken to someone like you
@ford873
@ford873 3 ай бұрын
No, sorry
@aakashdeep5238
@aakashdeep5238 5 ай бұрын
Thank you… worked for my Taigun (T-cross) in India.
@ford873
@ford873 3 ай бұрын
Glad it helped
@paulkillick3419
@paulkillick3419 5 ай бұрын
Hi, I’ve not long taken ownership of a 2019 VW 1.5 DSG evo bluemotion and this coasting thing in my opinion is ridiculous and here’s my issue. In eco or normal mode with the start/stop turned on to stop the car from cutting out and starting every time I stop the coasting facility still causes the engine to stop and then start again and the only way to stop this is to drive in sport mode. I’m no alone with this as several Golf and Skoda owners have posted the same thing. I have access to a new VCDS unit but need to fine a suitable coding to switch the coasting feature off.
@stephanwischer9608
@stephanwischer9608 5 ай бұрын
Well done but how about the square bushing we see in the last seconds which is completely rotten? Would have been the easiest change.
@ford873
@ford873 5 ай бұрын
I do mention in the description for the video that not all the bushes were delivered / available when the job was carried out. The vehicle was needed back on the road and it was changed at a later date.
@rajmasih9797
@rajmasih9797 6 ай бұрын
How much should a repair like this cost
@lobo2k393
@lobo2k393 6 ай бұрын
20k around
@abualhaul9777
@abualhaul9777 6 ай бұрын
Thanks for this!
@ford873
@ford873 3 ай бұрын
My pleasure!
@Hzzr013
@Hzzr013 6 ай бұрын
Thanks love from Russia
@ford873
@ford873 3 ай бұрын
Welcome!
@goonluv
@goonluv 6 ай бұрын
Wow mine was to big off ebay
@xymplon9978
@xymplon9978 6 ай бұрын
Thankx for this extensive calm video, it helpt me a lot analysing my shifting troubles. A good sober detailed video is just a joy !
@ford873
@ford873 6 ай бұрын
You're very welcome!
@andreasbroge4043
@andreasbroge4043 7 ай бұрын
thanks a lot. Nice work, will be proofed by myself tomorrow.
@ford873
@ford873 6 ай бұрын
Good luck!
@shaheedjanuary9977
@shaheedjanuary9977 7 ай бұрын
Great video sir. Can you provide me with the part number for the retaining rings. Thank you very much😊
@ford873
@ford873 7 ай бұрын
I'm sorry but I cant, the job was done a very long time ago and I no longer have the vehicle information to look it up. If you contact any Volkswagen dealer, they will be able to supply the parts. Some dealers can be funny about giving out part numbers over the phone though.
@anvercassim7663
@anvercassim7663 7 ай бұрын
How can I remove the gearbox of a polo 1.9 tdi
@xero5727
@xero5727 7 ай бұрын
I have a diagram that has notes say: * Through November 2015 *3 From November 2015 what does the "Throuh" mean?
@ford873
@ford873 7 ай бұрын
You can have contradicting information in the key. It would only be a concern if both of those were applicable to the same wire though? The through I would imagine just means that if your car was manufactured during November of that year, this applies to that wire.
@mynty2864
@mynty2864 7 ай бұрын
What is the Gearbox Code?
@ford873
@ford873 7 ай бұрын
Sorry but it was so long ago i no longer recall the gearbox code.
@jeandesflorettes9071
@jeandesflorettes9071 7 ай бұрын
perfect
@ford873
@ford873 7 ай бұрын
Thank you very much.
@bigbaudiboiis-ne8gd
@bigbaudiboiis-ne8gd 7 ай бұрын
What program is that?
@ford873
@ford873 7 ай бұрын
The wiring diagrams were edited using Adobe Photoshop and they were blended together using the editing software Hit Film. Sadly there is no actual wiring diagram software that I am aware of that operates like this. Although that would be pretty awesome if it did.
@garydevine4556
@garydevine4556 7 ай бұрын
Thank you very helpful
@ford873
@ford873 7 ай бұрын
Glad it helped.
@SPaul-ym4fz
@SPaul-ym4fz 7 ай бұрын
Thank you so very much for this! ☀️
@ford873
@ford873 7 ай бұрын
You are so welcome! Glad I could help. Did you have the exact same issue?
@SPaul-ym4fz
@SPaul-ym4fz 7 ай бұрын
@@ford873 the car comes next week..
@anndavidson4795
@anndavidson4795 8 ай бұрын
Simple when you know how 🤣🤣 Thank you so much.
@ford873
@ford873 8 ай бұрын
You are so welcome! Glad i could help.
@user-mo8oo2gs7y
@user-mo8oo2gs7y 8 ай бұрын
Absolutely brilliant video and so simple, when you know how. Got a new golf this month and although I had the same basic golf for the previous two cars, this car has been a nightmare. The salesman could not have been more helpful, but I would have had to take him home for the first month.
@ford873
@ford873 8 ай бұрын
Glad it helped.
@shehadiyasamshu1363
@shehadiyasamshu1363 8 ай бұрын
General motor wiring diagram is very easy to read and understand, in this diagram how i know 5v reference or low reference or control module ground.
@ford873
@ford873 8 ай бұрын
Its not always easy, on the newer diagrams they are starting to label them with a little 5v symbol. On the older ones its a process of elimination like I did in the video with the live feed. They just did not and still do not always label them.
@jamiebale9642
@jamiebale9642 8 ай бұрын
How to stop the Timezone from reverting back to Japan Timezone, every time the car is turned off? We are in Australia.
@ford873
@ford873 8 ай бұрын
If it is changing on its own and you have the time zone set correctly i would imagine it is most likely a software update.
@TommyW72
@TommyW72 9 ай бұрын
Very good video, thx for that! When I did the bush replacement, I felt it easier to press the smaller ball into the cup (already assembled into its mount) outside the car and install the T-shaped rod together with the cup mount back to its place.
@ford873
@ford873 8 ай бұрын
Great tip! There is lots of ways that all work equally well.
@user-zo9ui6xs4o
@user-zo9ui6xs4o 9 ай бұрын
Just got my new Golf style today! Very helpful, thank you 😊
@ford873
@ford873 8 ай бұрын
Glad it helped!
@marenko1239
@marenko1239 9 ай бұрын
Finally someona who have this car, Thank you
@ford873
@ford873 8 ай бұрын
You're welcome.
@ponasfeliksas5299
@ponasfeliksas5299 9 ай бұрын
You brits annoy the hell out of me…stop talking utter bullshit and go straight to the point
@SuperRhysevans
@SuperRhysevans 9 ай бұрын
I only got three bushes with my repair kit ??
@ford873
@ford873 8 ай бұрын
Depends on who and where you buy them from.
@hamshankerbank
@hamshankerbank 10 ай бұрын
Awesome.👍
@ford873
@ford873 8 ай бұрын
Thank you! Cheers!
@roadvu8688
@roadvu8688 10 ай бұрын
Brilliant, simple, it works for my 2019 e-golf, thank you
@ford873
@ford873 8 ай бұрын
You're welcome!
@user-ek6fk7kw3c
@user-ek6fk7kw3c 10 ай бұрын
hello! could you help me with some advice? the fact is that my volkswagen up! (2013, the gearbox is robotic) needed a box replacement due to an adaptation error. In the process of replacement, the thermostat housing was damaged. I'm trying to find information - was there a need to remove it in the process of replacing the gearbox - and I can't find it.. after watching your video about the removal, I did not see that the thermostat housing interfered, and the car is now in service and is not available to me. Could you tell me if the thermostat really interferes?
@ford873
@ford873 8 ай бұрын
I have never needed to remove one or have it interfere with removal or replacement. So unsure how they could have damaged it. I would imagine its more a case they noticed it was leaking when they removed the gearbox and it needed replacing?