Can you tell me, my marshar does not turn on, but if I put it on the charger, then on the indicator 2 lights up 1 does not light up 2 lights up 1 does not light up 2 lights up. What kind of error could this be?
@JonnyFix4 күн бұрын
Have you left it on charge a long time to see if more lights come on, maybe battery is very flat. Maybe first light is broken and should be lit so looks odd.
@AvatarStark7 күн бұрын
My EdgeSwitch24 (500W), when disconnected from power and reconnected, resets all connected NanoStations to factory settings.
@JonnyFix7 күн бұрын
That must be very annoying
@AvatarStark7 күн бұрын
@@JonnyFix You don't know what could be causing that problem.
@JonnyFix7 күн бұрын
@@AvatarStark Sorry mate, I've not seen that before. Others are saying the unit will reset if it detects voltage on the ethernet data pairs, this isn't a fault it allows them to be reset remotely, so induced voltage due to startup current in the cables or not using shielded ethernet cables, maybe they are running next to power cables as well. The shielded cable should have shielded terminals that ground the cable to the switch chassis. This will prevent induced voltage from adjacent cables.
@beelerspace9 күн бұрын
This was exactly the video I needed to repair my daughter's HP Pavilion laptop. Thank you!
@JonnyFix7 күн бұрын
Excellent! Well done.
@pasromano759 күн бұрын
I'm often seeing videos about broken medelis.... For me , too cheap products. I'll buy a Casio !
@MukeshMohan-f1u13 күн бұрын
What is the price
@obj-26016 күн бұрын
I think my coolpix l340 has a broken image stabilizer, bacuse it make a violent shake from left to right when I slightly move right or left. Can it be fix?
@y.cbeats16 күн бұрын
Hey there i have a sony amplifier where some of the channels have no sound output how can i fix such
@NotJames117 күн бұрын
I have an SP5500 that I was going to give away to my nephew but it's been a while since I used it. I remembered why once I turned it on; the left speaker crackles depending on which key I press or how hard I press. If it's the speaker then is it a simple thing to replace? Would you be able to point me in the right direction to the right part? Any help would be greatly appreciated.
@JonnyFix17 күн бұрын
It sounds like some resonance causing some stuff to vibrate. Check there's nothing sitting on the speaker cone. If you press evenly on the cone it should move freely up and down. I think the speakers are the same, you could swap left and right as stereo piano makes left move more for low notes so any issue may not show up in high notes. If you do and it still crackles it could be an electrical problem. Any speaker same physically and resistance should be fine to use.
@JonnyFix18 күн бұрын
There's now a download link for this model in the video description.
@grafikerburak18 күн бұрын
Can you write your email please?
@JonnyFix18 күн бұрын
I've put a download link in the video comments. Thanks, hope it works for you.
@grafikerburak17 күн бұрын
Thank you so much Jonny
@RichardFrancis-e6n18 күн бұрын
Another one saved. Thank you, Johnny Fox. You're a GENIUS 😁
@TheDefpom18 күн бұрын
Hey Jonny can you email me please, you can find my email on my KZbin about page.
@silentsapper206119 күн бұрын
Great video and instruction! I have this same subwoofer. Mine powers on but produces a red, white, and amber light cycle. I can get it to pair on the app and display, but there is no bass. Do you have any ideas of what this could be, and is there a video to fix this? I watched this video hoping it would give me some insight. searched all over their site but got no answer.
@JonnyFix19 күн бұрын
Others are saying it has something to do with firmware. I don't remember if this setup can be network connected but if so do that using LAN cable preferred to WIFI and leave it on overnight, see if it downloads an update. Or find a way to do an offline update maybe via USB?
@yulaw511021 күн бұрын
Mine is making noise but it doesnt look like the water is getting agitated
@JonnyFix19 күн бұрын
Put a piece of aluminium foil in, it should create holes in it. There are videos showing what to expect. Make sure any power control is set to maximum.
@d1rty1oser22 күн бұрын
Very good video. Thank you very much! But is it just my imagination or did some smoke go up next to the green wire at 38:59?
@JonnyFix21 күн бұрын
Interesting, sure looks like it. The unit is still working fine though.
@erikdenhouter22 күн бұрын
I would have used the tiniest core of wire I could dig up, like one core from the thinnest wire in the house. Thin enough to act like a fuse. Thanks for the info, pin one for the backlight.
@mtbarr6423 күн бұрын
In case no one has responded the unit is WORKING. Turn off the "CD Direct" and the other botton. When in "CD Direct" mode the unit TURNS OFF THE DISPLAY. I noted you never used this unit when working. The MASTER button is the main power which puts the unit into "Standby" mode with NO display. When you hit the bigger button the unit actually powers on, with the DISPLAY being the key indicator that it is working! So this unit was FIXED Thanks for the detailed troubleshooting. I will be doing my own shortly.
@georgeglas6824 күн бұрын
If you did research first then you would have known about the comen problem of the protection circuit. The zener diode runs hot & causes damage to the capacitors. You don't need to remove the protection circuit. Just remove the back panel. I sell the kits on ebay with full instructions. NADC370.
@JonnyFix24 күн бұрын
Why research when you can have fun figuring it out 😊
@georgeglas6824 күн бұрын
@@JonnyFix Well doing research saves time. He did not show the correct or easiest way to carry out repairs.
@JonnyFix24 күн бұрын
Everyone's an expert right
@GalAxy2eins24 күн бұрын
I have a 30V5A difference name version WPS305H but the electronic is same i think software regulates 5 or 10amp
@SteveMinecraft-n6v26 күн бұрын
Hey what plastic polish did you use if you don't mind me asking?
@JonnyFix25 күн бұрын
It was from a CD repair kit but any polish for transparent plastics like car headlights should be fine.
@englishrupe0126 күн бұрын
Excellent review and teardown....many thanks.
@jonome956527 күн бұрын
Thank you Jin Thao for all the tear downs. Any chance you can do a tear down of the Ninja foodie AF400 I need to get to the circuit board but cant work out how to get the frame off. Cheers
@Sen4D28 күн бұрын
After replacing the diode the device goes on and works sometimes a minute sometimes longer then it turns orange, off, white on and works again. And this goes like a loop. With the 3,5mm jack same issue. Any idea ?
@JonnyFix26 күн бұрын
No sorry
@Sen4D28 күн бұрын
After replacing the diode the device goes on and works sometimes a minute sometimes longer then it turns orange, off, white on and works again. And this goes like a loop. With the 3,5mm jack same issue. Any idea ?
@richardsmith4992Ай бұрын
The build quality here makes me cry with sadness.
@MiracleMAXАй бұрын
Top quality unit right there!
@TheDefpomАй бұрын
@12:50 one thing you could do there is use some component leads and add them as bracing to other ground points, have done that myself in the past when the traces weren’t very strong
@JonnyFixАй бұрын
True. I've done similar things it just didn't cross my mind. Gotta stop doing stuff half 😴
@TheDefpomАй бұрын
Audio is better on this one
@JonnyFixАй бұрын
Cool
@davidharris1817Ай бұрын
another success story here, but I only had full size diodes so added a 1N5406, now works perfectly, thanks matey :)
@ty-and-brittАй бұрын
That red piece fell out for me. There is a thin metal pin that sticks up. Is that red piece supposed to cover that pin, or be adjacent? I put it all back together with it adjacent, I couldn't make the red piece fit over the pin without forcing it.
@johnhousego9218Ай бұрын
Audio quality good but its clipping a bit. Thanks for the video.
@Sen4DАй бұрын
After replacing the diode the device goes on and works sometimes a minute sometimes longer then it turns orange, off, white on and works again. And this goes like a loop. With the 3,5mm jak same issue. Any idea ?
@retitituАй бұрын
„fat ass d:“ made my day. love your content and attitude
@MiracleMAXАй бұрын
Top job! 😁😁
@TheDefpomАй бұрын
I think you should stick to your original audio setup, this one sounded way too harsh and clipped, I think your normal audio sounded fine.
@JonnyFixАй бұрын
I always thought the mic I used with microscope wasn't as clear and the plosives were annoying. There was also a background hum. Maybe I turn the gain down.
@TheDefpomАй бұрын
@@JonnyFix maybe try turning down the compression settings to soften it, reduce the compression ratio, might be enough.
@MiracleMAXАй бұрын
Pretty hard to sort it when they remove the IC numbers. Very frustrating! Good diagnosis 😉
@JonnyFixАй бұрын
I may have jumped the gun on that haha... possible follow up vid to come.
@MiracleMAXАй бұрын
@@JonnyFix Yeah, I've got a few in the pipeline - fixed and waiting (hopefully) to be fixed. Look forward to the follow up 😊
@mikemd866Ай бұрын
replaced the battery of my fenix5s to a larger one. initially it charged to 61%, but it wont charge to more than 4% now and will get quite hot when charging. what could i do? :S
@JonnyFixАй бұрын
I'd put the old one back in and see if it behaves as it used to, if so get a new original size one. If it still gets hot something may have got damaged. It's possible the battery is a dud, see if the heat is coming from that or the watch itself.
@songaiback_up2761Ай бұрын
Apa type c yang di pakai marshall itu khusus kalo husus tolong beri tahu saya type atau namanya karna punya saya rusak.
@JonnyFixАй бұрын
It is unique to Marshall only. I cannot find them anymore.
@nnbprasad5481Ай бұрын
Sir r u repair smart watch
@kabulozo25Ай бұрын
Good afternoon I wanted to know if you can help me I wanted to connect the gas meter What wire is it?
@Clairette89Ай бұрын
It's very impressive! I have the same problem on my keyboard and I really would like to replace the broken pieces. I've seen that you have printed them. Would it be possible that you print them for me and that I pay you for the service?! You have the best solution I found until now. I can pay with PayPal or Bank Transfer. Let me know what is possible. I really would like to repair my keyboard 🙏
@JonnyFixАй бұрын
I'd feel bad selling this design as it isn't perfect. You can get the working files here and edit the design and print your own. It's not quite right for the black keys and and can falsely trigger a hard press on white. I recommend only replacing completely broken keys to extend the best playing experience unless you can better this design. Good luck! file.io/83xNIIlNByyk
@grafikerburak21 күн бұрын
Your patience in fixing this is admirable. Sharing the file also requires us to thank you. Thank you very much. But now I see that the file has been deleted. Can you please share it again?
@JonnyFix21 күн бұрын
@@grafikerburak Reply with your email and I'll send it direct as the free sharing site doesn't work here.
@grafikerburak20 күн бұрын
I write my email, but my comment does not seem to be deleted. Can you send it by typing gmail after typing grafikerburak?
@grafikerburak19 күн бұрын
I write my email, but my comment does not seem to be deleted. Can you send it by typing gmail after typing grafikerburak?
@aussiefilm1Ай бұрын
Thank you very much for the video, I followed it and was able to replace a thermal fuse in my air fryer. The exact same one as in your video. Saved me buying a new one and has given me the satisfaction of being able to fix it.
@myblack6636Ай бұрын
Thanks Jonny for sharing! I have a question, what should i do to modify my ultrasonic cleaner from 40khz to 120khz. Changing the transducers to 120khz ones is obvious, but how should I modify the oscillator?thx
@JonnyFixАй бұрын
Sorry, I'd have to research that myself. I do know that bonding the transducers to the tank is quite difficult if you were to change them.
@MMrzАй бұрын
I'd love to know what multimeter you're using
@JonnyFixАй бұрын
The Fnirsi 2C23T. It's new, I might do a video on it.
@АлександрСереда-у7мАй бұрын
Помогите найти схему блока питания. Пожалуйста
@zachz96Ай бұрын
Why did someone ruin this?
@JonnyFixАй бұрын
They thought they were clever screwing it to a board right after being told they shouldn't
@domenicodenisi8636Ай бұрын
Grazie mille 🙏🙏 ho riparato il mio Bose con solo 1 euro!!
@fransonrodrigues2637Ай бұрын
Hello, I am having trouble with my Bose subwoofer. The sound is not coming out. Could you please help me with this issue?