6 жыл бұрын
Пікірлер
@carlosruiz9963 Күн бұрын
this rectifier boards suck, in less than 2 years they will fail and 8 times out of 10 the transistor will burn too many components , nothing like the good' old simple wired transformer
@fffinga Күн бұрын
Thank you for this video. Your efforts are well appreciated sir.
@geeyore7726 9 күн бұрын
Thank you, this was the fix I needed. That pesky relay. Very nicely presented.
@jewelmadathi2211 16 күн бұрын
Igbt number give me please sir
@cavemansmancave9025 20 күн бұрын
Miss you guys. I have the same issue with videos. I haven’t done one in a few years, myself.
@pierresgarage2687 20 күн бұрын
It's more or less retirement, or something similar... 😉
@rpsmith 26 күн бұрын
Awesome video! Thanks!
@pierresgarage2687 25 күн бұрын
Glad you liked and thanks for your comment...
@patchcabletube 29 күн бұрын
Thank you very much for your efforts. I had an issue where a recent model would stop after a few seconds but wouldn’t even run the inverter, kind of silent, after checking all the connections in your order it’s working again. Hope it’s not a temporary fix don’t want to have to dig out my multimeter. Thanks again
@pierresgarage2687 28 күн бұрын
If you're like me, you will dislike not being certain you found the real problem and fixed it once and for all... 😒
@jamesbanjomanjohnson 29 күн бұрын
sometimes it works better if you take a drink of the oil in between the dunking of the steel pieces, that check's the temperature of the oil as you go, never wipe the oil off your rag in between the dunking as this just adds more excitement to the process...
@pierresgarage2687 29 күн бұрын
After a couple of those drinks I'd keep close to the potty, ank keep the rag to whipe my tutty after the high pressure shit shower... 😵💫
@acbennettcfi Ай бұрын
New hobby machinist. I've been trying to wrap my head around these. This was the most concise and detailed explanation that a total beginner could understand, Thank you!!!!!
@pierresgarage2687 29 күн бұрын
You're welcome and thanks for your comment...
@тмє-ъ4х Ай бұрын
👍
@dikhed1639 Ай бұрын
I apprecieate your explainations. So many peeps blab on about their dog or their recent medical problems or other crap rather than some information that the viewer wants to see/hear. Thanx.
@pierresgarage2687 29 күн бұрын
Agreed, you're welcome and thanks for your comment..
@HoangNguyen-gy6rv Ай бұрын
sorry but my spirit level is off when rotated 180 degrees, even though I adjusted it it is still off when rotated, is it broken?
@pierresgarage2687 29 күн бұрын
Not certain, but, I think you may not be in the leveled axis of the surface you're using... Cause when you adjust the level properly there is no other choice of being right unless the vial is really installed wrong or defective...
@mondotv4216 Ай бұрын
So if there's only 67 Ohms between the magnatron terminals and case that's a dead magnatron right? Should read open, shouldn't it?
@pierresgarage2687 29 күн бұрын
if my memory serves me right, from the two terminals to the body there should no reading on the resistance function, as between the two terminals the reading should be a near short circuit, if not the magnetron is surely defective.
@СуперканалВлада Ай бұрын
9:01
@theonlyalan731 2 ай бұрын
My 0xa tool holders that I got from Little machine shop had to have all of their Hardware replaced for the same reason. But the shars holders that I bought have fantastic Hardware
@pierresgarage2687 28 күн бұрын
Those blocks were ordered from Shars, possible that they got comments and changed their set screws since. This video was made some 9 years ago, quite a while ago....
@brainfeeding 2 ай бұрын
Thank you for this video,i changed the Gt60n321 IGBT but when i start microwave,IGBT blows again and i need to change it again, I'm so confused, magnetron is ok
@pierresgarage2687 28 күн бұрын
Most times there is more than the IGBT that will blow, you need to look for the other parts that drives the IGBT, cause it most likely takes along other parts around when it blows, or, some of those driving parts will cause the IGBT to blow... Other important parts to check, the HV trancformer, look for possibly burned windings, other coils, capacitors, diodes, etc...
@cuagainful 2 ай бұрын
HI, What if the microswitch wire connection is put the wrong way?
@pierresgarage2687 2 ай бұрын
If you put the wires on the wrong switch it will cause issues, but, if you invert the wires on the same switch it won't change anything cause a dry contact like in a mocroswitch isn't polarized. Hope it helps, let me know if you need more help, thanks for your comment... 👍👍
@blueskyvideos9798 2 ай бұрын
Great video Pierre! For a small or a beginner workshop its more logical to use a great MMA inversor (inexpensive compared to a good 300A mig machine) than a mig for doing jobs that require good penetration and trustability. Let those chinese mig's for make doors and windows. Thank you for sharing.
@pierresgarage2687 28 күн бұрын
I agree with you, a good MMA welder is a solid choice for a hobby workshop. Thanks for watching!
@mahmudalamin8504 3 ай бұрын
Good job 👍.
@pierresgarage2687 3 ай бұрын
Thanks for your comment.... 🙂🙂
@EngineerGordon 3 ай бұрын
it was a good lesson from you sir. thanks
@pierresgarage2687 3 ай бұрын
Hi, thanks for taking a moment to leave a nice comment... 🙂🙂
@walterwinnipeg7350 3 ай бұрын
Bonjour. Regarding the high-voltage rectifiers... From what I have read and seen, a regular multimeter won't be able to test these, because the forward voltage when conducting is several volts, not just 0.6 to 0.7V for standard silicon diodes. I have used a 12V power supply and a 1K resistor in series with the diode. Measure the voltage across the rectifier. Hooked up in reverse, the voltage across the rectifier will be the 12V of the power supply. When connected in the forward direction, the voltage across the rectifier will be anywhere from about 5V up to maybe 10V, depending on the device. Today, I was working on a Panasonic microwave (model NN-ST661B) with this exact same inverter module. One rectifier (D702?) was dead short, and the other (D701?) was okay. The inverter wasn't generating high voltage, so the microwave shut down after 23 seconds, just as it is supposed to for this failure mode. A replacement inverter is about $160 CAD.
@pierresgarage2687 3 ай бұрын
It's possible to take a chance to find a supply for replacement diodes, ( Digi-Key, Mouser, etc) I don't have on hand the number or reference of that diode since There isn't a microwave open close by. One possible way to avoid paying 160$ would be to get a used microwave that works, even if the outside apearance isn't great, all you need is the board, by checking the model number and refering to the proper service manual you'll know if the board is compatible. Note that many models of inverter series within the same power range share the same board... I hope you solve your problem... 🙂
@walterwinnipeg7350 3 ай бұрын
@@pierresgarage2687 === all you need is the board, by checking the model number and refering to the proper service manual you'll know if the board is compatible. Note that many models of inverter series within the same power range share the same board... === I actually do have the service manual for this microwave oven. And it does give the Panasonic part number of the inverter board. But, what I'm not sure about is, which other inverter modules could be used to replace the one I have. If you go to eBay, and search for Panasonic microwave inverters, there are quite a few available, both new and used, often with slightly different model/part numbers. They all appear to have the same form-factor, same mounting, same connectors at the same locations labeled the same way. Maybe all earlier or later versions of some kind of "inverter family"? Intuitively, it would seem that any of these could be installed and would probably work. Do all of these inverters put out the same high-voltage DC, controlled by that 3-pin cable from the display panel? Anyway, it's academic now... The owner of the microwave (not me) decided enough time had been spent in this repair, and they will buy a replacement oven. I scrapped the oven, but salvaged the useful bits (panel, turntable, fan, switches, etc.)
@moniquegilks9694 3 ай бұрын
Where can I buy these drill bits?
@pierresgarage2687 3 ай бұрын
Those can be purchased from many sources, starting at you local hardware store, eBay, AliExpress, etc... Note that the quality will vary depending on when and where the items were manufactured. Mines were purchased quite a long time ago from local hardware store.
@bendishrock 3 ай бұрын
NN-T945SFX - blows fuse immediately upon pressing start. What could be the problem?
@pierresgarage2687 3 ай бұрын
Most likely that that either the high voltage board and/or the magnetron are defectives, look in the description for the links to the service manuals, if you're familiar with electronics there is a section on what measures to take in order o test the magnetron and some of the components on the high voltage board. Though, mostly if you're not familiar with high voltage units be very careful not to get injured...
@Vision20247 4 ай бұрын
I’m now confident to go repair the not more than a couple years old Panasonic Inverter microwave in the household. I think you should go teach this as a skill if you aren’t yet doing so…
@pierresgarage2687 4 ай бұрын
Thanks for a nice comment... This video is a short overview on how an inverter type microwave works, it's a good start on trying to diagnose the most common problems. I'm now retired and not planning to make many more videos since those productions are quite demanding in time and resources. The best thing is that the microwave keeps working without failure.... 😉😉
@redwow 4 ай бұрын
As one side moves, doesn't it cancel out the other side? Result, no change in outcome speed. I'm missing something.
@pierresgarage2687 4 ай бұрын
As one gets smaller the other wheel gets bigger, then, the ratio is is lets say 2 to 1 in one direction, as it shifts to the other side the ratio will be 2 to 1 in the other direction. this setup allows the change without the need to change the length of the belts cause the variable pulleys travel along the slide bars. You need to figure that the pulleys on the motor and the other one on the driven tool are constant in size. the ratio is directly proportional to the diameter of the drive pulley over the driven one.
@uomopozzanghera 4 ай бұрын
Could you please explain how exactly you shorted the inverter before starting the repair? The service manual says to short the inverter output terminal of the magnetron filament terminal to the chassis ground, but it is not clear (to me) where the former is. Thanks!
@TodorTashev 4 ай бұрын
I appreciate the precision and consistency of your work. It's a pleasure to watch.
@pierresgarage2687 4 ай бұрын
Many thanks for your nice comment... 🙂
@joansparky4439 4 ай бұрын
neat.. just neat. 👍
@pierresgarage2687 4 ай бұрын
Thanks for your comment... 🙂
@MegaRiffraff 4 ай бұрын
👍🏻
@ivanhoyt7757 5 ай бұрын
Great video!! What oil do you use to quench?
@pierresgarage2687 4 ай бұрын
Canola and olive oil mix. (From the kitchen reserve when it starts to spoil... 😊) Thanks for your comment...
@ivanhoyt7757 4 ай бұрын
Thank you!
@ZeroRugrats67 5 ай бұрын
Glad this video is still here. I was trying to figure out how to calibrate an angle iron. Feeler gauges and a cylindrical square. Thank you!
@gie51917 5 ай бұрын
Fascinating. My machine keeps saying E30. I checked the drain hose and it's fine. The water filter is clean. I wonder if the problem is in the pump, then.
@Lifesituations8000 5 ай бұрын
What would cause that panel not to come on?
@noe29933 5 ай бұрын
❤
@pierresgarage2687 5 ай бұрын
thanks...
@esteeocanal385 6 ай бұрын
Please, can you tell me how the communication between the control board and the HV board works? I'm looking to replace the HV board with a common transformer. But I need to make sure the HV board doesn't turn off. I intend to assemble a circuit to simulate the signal from the HV board that goes to the optical coupler.
@esteeocanal385 6 ай бұрын
Olá. Eu estou reparando um forno parecido com esse. O meu forno está com problema na placa inverter. Parece que não está passando o sinal PWM pelo acoplador óptico.
@juanantillonm 6 ай бұрын
Hi! Do you know the model number of the inverter that is used for the microwave oven Panasonic NN ST651W? The repairing shop return my oven without the inverter installed. The 2technian" include in the package two inverters and a notesaying that all the inverters are similar, but he takes out the inverter of my oven and he is later confused what are the inverter that came installed originally. I must know the mentioned info to recover my original inverter.
@pierresgarage2687 6 ай бұрын
By looking in the service manual we get : F606Y8X00CP H.V.INVERTER (U) This should be a good number, this board seem to be used in a few similar models. Hope it works for you....
@nowar9220 6 ай бұрын
But why? Older mutitoyo cmm are like 5k - 20k usd Maybe it was broken? Just seems illogical Got the answers to my own questions 😂😂 pays to be patient..
@marcmedina1259 6 ай бұрын
The magnetron anode touches metal within the mounting housing. Is that normal?
@pierresgarage2687 6 ай бұрын
If the magnetron housing is isolated from the unit and there is one of the side that makes contact with the case, there is most likely a problem with this magnetron. Look out on Ali express or Ebay using the number on the unit, you should find something in the 30 to 50 USD range. look out for burnt windings on the High Voltage coil or anything wrong ont the HV board... Let me know how it turns out...
@michaelcapp4597 6 ай бұрын
A very good tutorial thank you for sharing
@pierresgarage2687 6 ай бұрын
thanks for your nice comment, glad it helped you... 🙂🙂
@astafford8865 6 ай бұрын
Hello Poerre. Can you tell me please. Do you short the capacitors on these Panasonic inverter microwaves,please? And if so .Can you tell me please. How you do it more safe? Thank you and nice video.
@pierresgarage2687 6 ай бұрын
It's always safer to discharge those capscitors, the best way to procede is to get an appropriate resistor and a wire with aligator clips, you clip one end with the resistor to ground or one lead of the capacitor and with the other end you touch the other end. Avoid touching with both hands or making a part with 2 opposite body parts.....
@astafford8865 6 ай бұрын
Thank you Pierre for the reply. Are the capacitors easy visible? . I was told it was near the green part of the Inverter board. I only saw a picture so far. I haven't seen the real one yet. Many thanks for the reply.@@pierresgarage2687
@pierresgarage2687 6 ай бұрын
As I remember they are quite easy to reach, if an aligator clip doesn't do it you can use meeter probes with a needle point to get the same result, after discharge use the meter to check for residual voltage, though, be careful with the kilovolts rated parts not to overload you meter's capacity. If you're not rxperienced with electric circuits and electronics, be really careful not to cause yourself injuries...
@vlota 6 ай бұрын
Something really odd about using calipers accurate to three decimal places but with those ludicrous imperial units. I s'pose it might come in handy for those times when you need something to be exactly 234762 millionths of an inch.
@emailformosa 6 ай бұрын
*Nobody clicked this video because they cared about the first **3:15* Get a diary, a female friend, or a sense of stoicism, and get to the point.
@EdCarlosRocha 6 ай бұрын
Hi Pierre, Great video 📹. I'm still trying to understand the resistor graph. In the range of 90 to 130 VDC Does the graph go from a minimum of 1/100 to 1? Is this unit referred to with HP power? For the KBMD-240D with 1/2 engine. So does this mean that at 1/2 HP at 115VAC the resistor must be 0.025 ohms? Thanks
@pierresgarage2687 6 ай бұрын
You're right about the .025 ohms resistor for th e half horse motor. I'm reading the same as you... 👍 Thanks for viewing and for comment, Pierre
@noanyobiseniss7462 6 ай бұрын
If the wife has carbide inserts in her pocket then my only question is does she have a sister??? :D
@pierresgarage2687 6 ай бұрын
Nope...!!! 😉
@riversister23 7 ай бұрын
I removed every piece of drain and made sure there was nothing blocking, but I did not open up the pump impeller casing. The drain error code f21 was intermittent. Thank-you for this video as I was finally able to confirm the problem. I had hoped to buy just the pump but had to purchase the whole pump/drain together.
@pierresgarage2687 7 ай бұрын
Thaks for your comment I'm glad the video helped you diagnose and fix your problem..... 😉👍👍
@schifoso 7 ай бұрын
I have the exact same jack and it won't hold a lift and also leaks oil. I only use it for lifting lighter weight things like lighter parts of a vehicle like a wheel when replacing control arms. Your video is incredibly detailed and concise. Better than a training video. I'm going to try and repair mine as I've had it for so long that I can't bear to part with it. Quick question. Do you remember how much jack oil it took to refill after re-assembly?
@schifoso 6 ай бұрын
I ended up cleaning mine up and it didn't take much oil at all. When re-assembling, if you're having problem lining up the bottle jack part into the main assembly, you can lift up on the saddle and that will change the length of the whole assembly and make lining up a lot easier.
@atvheads 7 ай бұрын
Fuck inches.
@brandiveh 7 ай бұрын
I have a starrett 98-8, something was dropped on the edge of the vial opening and made a tiny nick and now the 2 cylinders smoothly twist each other only up until hitting the nick and then stiff to twist. Also the vial broke. Can it be fixed. Bore out the bent one maybe
@pierresgarage2687 7 ай бұрын
About the tubes, depending on how much of a dent there is, you can possibly reshape or lightly rebore it and/or lap the cylinders. If the dammage is too extensive and if you want looking like new part just be aware that you can order brand new parts from Starrett or some distributor, that is also true for he vial either alone or installed in the tubes. Let me kno how you managed and thanks for viewing
@brandiveh 7 ай бұрын
Ok, great info, didn't realize a tube was replaceable @@pierresgarage2687
@Zen_Modeling 7 ай бұрын
😂😂😂
@pierresgarage2687 7 ай бұрын
Thanks for your comment... 😉