Awesome idea! I think you saved me.

Thank you for the video and the instructions, sir. I just have one question. How do you remove the metal flange

@tremaynestrucks, is there any room to telescope the column towards the firewall? Any adjustment there?

best video i've seen to date. great job

I just followed your video and the gauge selector is crooked. I have the tab in the column and it’s just a little off. I can send you pictures on Instagram if that helps any.

I wish I watched this after I spent hours struggling with my door today :(

Great video! Everything I needed to know.

You don't show how the tack is connected or disconnected! Lol I'll Google that... lol

At what point do you install the window felts?

At what point do you put on the felts

How to put bck on 78 c10 steering column wires

Thanks! My 2001 Monaco coach uses these same switches!

Excellent. Thank you for taking the time to do this video.

The best tutorial on 67-72 window/door disassembly I have seen. I have taken many apart and it always seemed to be difficult, until now! Thanks.

Very good video. It helped me out. Thanks

Brother...I cannot thank you enough ! Just today..I was reinstalling steering column on my late Grandpa's 72 Buick skylark 4 door, And couldn't figure out why that bolt wasn't going through to hold steering column together.. I must be off by 1 spline... thanks brother!

71 GMC column shift automatic will not go into park unable to find out how to tear down to clean out the shaft where the shifter livers connect to the transmission

Jesus clips... Absolute gold

I wish you showed more of the inside of the door. But, thanks!

You Sir are a wealth if information and knowledge. Thank you for all that you share!

5 years later and you are still helping us folks...thank-you! I have two nice 1969 truck doors if anyone needs them. I bought them thinking they would fit my panel truck but they don't. :( I'm in Ohio.

Thank you so much. I was struggling for a while.

Keep them coming! Enjoy all the tips and tricks! Thanks!

That was pretty slick man. Thanks alot

Great video thanks for showing some tricks for the do it yourselfer. I need to do this to my own 69 and I do all my work solo. There's nothing better than a job you can do yourself and the confidence in knowing it's done right. Great content. You just earned a new subscriber.👍

Thanks!

I don't know what im missing here but my glass won't come out.

Awesome video. Huge help. Thanks for sharing

Extremely helpful! Exactly what i needed to learn today. Thanks!!

What if the door wont open, both of my doors on 72 truck will not work. Windows are open. And door is unlocked

Life saving video. You probably saved me hours of frustration.

Plug this one in to here and this one into here. Which wires go to what please.. color

DAMN RIGHT T.T. This is an excellent example of watch the stinking u-boob video BEFORE you take a pair of vise grips to your "oh this will be easy" project. I can tell you with all honesty that the threaded retaining cover will come off over the lock cylinder. As before mentioned, pipe wrench on the lock cylinder under the dash and vise grips on the thread on cover ring on the outside of the dash and twisting as hard as you can for 24 minutes. Or you can watch this video (2 minutes 22 seconds) find a paper clip (4 minutes 37 seconds cuz ur junk drawer is a mess) remove the lock cylinder (another 2 minutes 22 seconds cuz you're a clutz and drop the paper clip twice) 10 minutes max.

What if I lost the key?????

you might need a second wrench to hold the dash side oil line coupling. Be super careful when reconnecting the soft, brass oil pressure line.

Thank you for posting… couldn’t work it out on my own…

It was very helpful. Thank you

can you put these panels on a 67 door ? i was thinking of just removing the chrome trim on the top of the door panel and it should fit fine, but haven’t found any actual advice could you happen to know ?

the A/C is impossible for me to get past the lower dash metal to where it's dropping like what you show. I'm guessing one needs to get back in their and disassemble some of the hoses. I pushed in (forward) really hard and only got so far. No clue how one would ever get the A/C controller out, perhaps if you've done it, then the hoses were very damaged and old in the first place, mine are like brand new. BTW, I'm simply trying to change my two bulbs

I always put grease on those bottom bolts

Hey idk if u read ur comments but everything is on but i cant get the square part inside the truck

I have seen the rubber for the vent rubber on the outside, on top of the painted surface. But they can go direction. The bolt holes with threads are 1/4" X 20 and if badly rusted or freshly painted, a tap is best practices to clean out. After decades of working on older and newer, I use a bee bee size dab of anti-seize. If not for me, but the next guy. Good info and following the shop manual assembly steps. Have a good holiday season as now, it's the 3rd of December in 2022. But this shows everyone how times this info is as related to these classic trucks. DK, ASE Master Tech since 1978, retired.

Well done! Thanks for the awesome video!

Thank you once again.

this was exactly the video I needed!!!! THANK YOU!!!!!!!

Thanks for the concise, paced, illustrative demonstration. Sharing your experience helped me prepare and have everything to do the job. I am changing out the column on my grandfather’s truck, which is now my son’s. Been in the family since ‘71.

Man did I need your channel. I’ve got 10 of these trucks. Just want to build a couple nice ones. The 67 thru 72 are pretty common in my area . Most are pretty ratted out, so you need a lot of parts trucks. I’m really in need of a short box for 67 c10. Get ready for a lot of questions

I just bought new door panels and upper trim. I have checked multiple sites to make sure I have to correct trim pieces and I do. The holes don’t line up at all with the holes on the door. Am I missing something?

Will this work if my key just goes in and out all willy-nilly or do I need the key to stay stuck in the cylinder in order for it to pull out?

The price is gonna hurt but end result awwwwwwwwwwwwwhhhh👍👍👍👍👍