This in-depth video will show you how to properly remove & install a steering column on a 1967 - 1972 Chevy or GM truck / C10. Very helpful when swapping to tilt column.
Пікірлер: 65
@zweihammerheavyind.2911 Жыл бұрын
Thanks for the concise, paced, illustrative demonstration. Sharing your experience helped me prepare and have everything to do the job. I am changing out the column on my grandfather’s truck, which is now my son’s. Been in the family since ‘71.
@danielbryant58039 ай бұрын
Awesome...keep it in the family..! Got my grandpa's 72 skylark and had steering column rebuilt and trying to reinstall it...all original!
@deankay44344 жыл бұрын
As an ASE Master Tech since 1978, now retired yet building my own 67 C10 pickup, this is the best video instructional video I have seen. Going as far as to show the locating tab, neutral/safety switch and the flat of the intermediate shafts connector took you extra time and effort. Theses who don’t do this everyday have a friend and video to like, subscribe and save to their play list, unless they have a buddy they can share with. Excellence in training! My 67 did not a booster, so to add one the bracket is an offset to the brake pedals geometry plus, I have never seen the brace shown near the end, connecting the booster to the fender. I found that new to me, learning has occurred! I would guess you found an OEM tilt column from a motor home or van. Good for you. My greatest fear is to spend $800+ for some aftermarket column and not find parts that fit! We both know that seals go bad, bearings need greased, noise or squick someday. Sir, you have done justice to our profession. Thanks, liked, subscribed and saved to my play list. Just plain great!
@tremaynestrucks29973 жыл бұрын
Thank you I really appreciate the compliments. I highly recommend OEM column or IDIDIT
@danielbryant58039 ай бұрын
Brother...I cannot thank you enough ! Just today..I was reinstalling steering column on my late Grandpa's 72 Buick skylark 4 door, And couldn't figure out why that bolt wasn't going through to hold steering column together.. I must be off by 1 spline... thanks brother!
@PATPAT-bg4wx2 жыл бұрын
This video is REAL helpful, thank you. As a complete novice I disassembled all of my 71 column 5 years ago, and realized today guess who didn't mark the upper shaft to the pot joint☺. Would have been so much easier. So with your video and some study of the parts, I realized so long as everything is square (emphasis) with the pot joint, clamp and shaft for the bolt then it's going to be right. BTW, you make it look easy. We have the same color truck.
@j0er0ckhead2 жыл бұрын
Very nice to list the tools, so they are ready, great instructions. Thank you
@53az503 жыл бұрын
The detailed explanation of each step is friggin' awesome! Much appreciated!
@jdbalance3 жыл бұрын
Very in depth and much appreciated! Didnt realize I was missing parts until I saw your video. Thanks for taking the time to shoot, edit, and post this!
@tremaynestrucks29973 жыл бұрын
You are welcome. Thank you for watching
@alphaditto11 ай бұрын
You Sir are a wealth if information and knowledge. Thank you for all that you share!
@colbycason5183 жыл бұрын
Appreciate you, followed step by step, painless!
@DadsToyBox4 жыл бұрын
Subscribed. I just recently bought a 1970 C10 and this info is perfect. Look forward to more.
@tremaynestrucks29973 жыл бұрын
Awesome. Thank you
@chriskimasta3 жыл бұрын
This was a great help nice job!
@tleav612 жыл бұрын
Great tutorial. Thanks for the info.
@Joseph-nw4mu2 жыл бұрын
Thank you Sir! Very Helpful!
@johnweeks41508 ай бұрын
Very good video. It helped me out. Thanks
@richardcedillo78392 ай бұрын
Thank you for the video and the instructions, sir. I just have one question. How do you remove the metal flange
@jaredwike85843 жыл бұрын
Thanks for the video!
@LJK691873 жыл бұрын
Awesome video!!!!!
@flatrat483 жыл бұрын
great video! Thx.
@raymond-19603 жыл бұрын
Hi, I just bought a 1969 C-10 and I need one of your hoodies Nice video
@tremaynestrucks29973 жыл бұрын
Pacific Paradise Apparel sells all my hoodies, hats, shirts, stickers etc
@bernardluschek37022 ай бұрын
@tremaynestrucks, is there any room to telescope the column towards the firewall? Any adjustment there?
@hogfit3 жыл бұрын
Thanks for the videos, they're always well done. Does anyone know where I can find the fiber optic line for the gear indicator? Thanks
@tremaynestrucks29973 жыл бұрын
I have them.
@tremaynestrucks29973 жыл бұрын
I apologise for the delayed reply. I have a few fiber optic cables if you still need it
@walterkparker94014 жыл бұрын
I have a 71 Chevy C10 and I found a tilt wheel that is slightly different from my non tilt. I understand the was and spring not needed but I don't understand it not having the automatic shifter 1/4 moon dog thing for the different gears to snap into to differentiate the gears?
@deankay44343 жыл бұрын
@Walter K Parker >Walter, it’s a little hard to figure out exactly what you have going on, but let me help. The arm that moves when you shift the gear lever inside, is welded to a tube so it moves as one piece. Now, round bar linkage is bent and shaped to make it around all the exhaust, brake and frame stuff. In the video, he showed the adjuster to get park and other gears in place. It has a special bold that is drilled to fit the round bar linkage. In an automatic, the shift shaft has inside, a strong flat spring & roller. It moves over a detent and falls into place to hold the shifter still. Up top, where the adjuster bolt is, this external round bar, bent by the factory, slides Into the hole of this bolt. The half-moon part is just like a cup, working as a washer does on any bolt. The difference is, it pinched down on the round bar shift linkage, to hold it still. Now, when the nut is tightened, it pinched the shift round bar, but a shoulder keeps it free in the arm that moves when changing gears. If missing, it would require a replacement pinch cup. The bolt fits just loose enough to move inside of the shift arm on the column. The arm can be straight or bent as shown depending on Model or transmission. This is just a pivoting pinch bolt. Look on older cars and trucks in your local bone yard. They maybe sold,, but I have not looked either. A company called “Lokar” May sell this bolt with hardware. A little research may turn up a missing part, unless your have everything, but the last guy who worked on it, installed it wrong! Hope this helps. ASE Master Tech since 1978 - Retired
@PANDA-PANDA592 жыл бұрын
We're did you purchase the steering column from
@mikegould66182 жыл бұрын
Great explanation of removing the steering column. I'm just trying to replace the rag joint on my '72 GMC. How do I make room at the steering shaft end so I can remove the old and install the new rag joint? Do I need to drop the entire column or is there some way to separate the shafts without doing that? Thanks for any help.
@tremaynelee27022 жыл бұрын
Thank you for subscribing. You do not need to remove the steering column to change rag joint. Just loosen everything and let the column drop an inch or 2 at the top and you can push the column up and get the rag joint off. The wiring and shift linkage can stay put as well
@mikegould66182 жыл бұрын
@@tremaynelee2702 Thanks so much for taking the time to respond. I appreciate the info.
@robbiematassa9603 Жыл бұрын
Hey idk if u read ur comments but everything is on but i cant get the square part inside the truck
@smokinvettelethal43833 жыл бұрын
I bought an aftermarket column. 70’ C10. The the bottom shaft is not splined. Will that still work or do I need a different coupling
@alexrivera4789 Жыл бұрын
Having the same issue.. what did you end up doing to resolve that issue?
@jameswoods5322 жыл бұрын
How do you close the clamp that holds the blot and 11/16 nut? Any pointer on how to do so?
@tremaynelee27022 жыл бұрын
I've never had to open it. It should just slide off. You might try channel lock adjustable pliers to close it
@michaelanthonyortegaherrer3482 жыл бұрын
I have a k 10 that how you adjust it I need to pull it out a bit so I can put the bracket on steering column
@tremaynestrucks29972 жыл бұрын
with the steering wheel installed just pull the column up into place and put the bracket on
@michaelanthonyortegaherrer3482 жыл бұрын
@@tremaynestrucks2997 I can't pull it I have to loosen the bolts on the fire wall
@christopherbrett50872 жыл бұрын
Great video but got one question, what are the size bolts needed to pull the steering wheel. I have a puller but the bolts are all too big. The holes on the steering wheel seem very tiny. Thanks
@tremaynelee27022 жыл бұрын
I'll measure them and let you know
@christopherbrett50872 жыл бұрын
@@tremaynelee2702 thank you very much.
@tremaynelee27022 жыл бұрын
The correct bolt size for pulling steering wheel is 5/16x18
@christopherbrett50872 жыл бұрын
Thank you very much. I just realized that the holes are welded or either the bolts are cut off in the holes. No wonder why nothing fit. Thank you again for all the help. But the guy who sold me the teething column got one over on me.
@christopherbrett50872 жыл бұрын
@@tremaynelee2702 Thanks again. When I pulled the horn contact and retaining clip, all I saw were the three screw holes for the clip. When you responded with the 5/16 and I cleaned up the area, I noticed the two holes to pull the steering wheel were filled with the screws, someone must have cut them level. Needless to say, I see now and not sure I can remove it as it is frozen in place. Thank you and I did subscribe because you have great content. cheers
@boujack72774 жыл бұрын
Genial
@jadenschroeder3393 жыл бұрын
Is the lower shaft supposed to be telescoping?
@tremaynelee27023 жыл бұрын
On 69-72 yes it is a double D shaft that is collapsible in the event of a head on collision
@alexisloveras58012 жыл бұрын
Is there anything different with doing this in a 1979 c10?
@tremaynelee27022 жыл бұрын
Yes it's completely different
@stevenbierlysr89859 ай бұрын
71 GMC column shift automatic will not go into park unable to find out how to tear down to clean out the shaft where the shifter livers connect to the transmission
@tremaynelee27029 ай бұрын
Most of the time lube will help. I spray PB Blaster in the hole where the shifter arm goes in the column and in the column on the end where the shift linkage attaches. I plan on doing a column disassemble video soon for non tilt column
@tauruswilson44026 ай бұрын
How to put bck on 78 c10 steering column wires
@tremaynelee27026 ай бұрын
I'm a 67-72 guy, I don't do squarebody
@rickramos84713 жыл бұрын
did u remove clutch pedal?
@tremaynelee27023 жыл бұрын
No I didn't. There is no need to remove clutch pedal
@tremaynelee27023 жыл бұрын
No this is a factory automatic transmission truck
@michaelangelaholcomb76563 жыл бұрын
Man I can’t get my steering wheel off how is it so easy for everyone else.... I have a 72 long bed stepside
@deankay44343 жыл бұрын
Using the correct thread bolts, the right size and length with the pulled shown works every time. This pulled and one like the OTC brand for removing the pitman shaft arm, will be the main ones in anyone’s tool box. You can use a penetrating oil a day before but shouldn’t be a problem. I am not ashamed to admit this, but with the nut loose but installed 5-6 threads, I grab the left & right side of the steering wheel, push on one side and pull on the other, repeating this back & forth real fast while pulling up, it comes right off. The nut keeps the steering wheel from hitting you in the nose. Never had a factory or aftermarket brake, crack, fracture or fail. These are tough. Note: Using good light, make sure it’s not tack welded or tightened over the splines. I have not seen everything from here, but I can only guess. ASE Master Tech since 1978-Retired
@stephenfaulkner14482 жыл бұрын
Dont you just love twisting up like a pretzel to get on a nut/bolt and drop you tool through and onto the ground? Ha
@tremaynelee27022 жыл бұрын
I really do love that, it's the best part 😂😂🥺
@taylorthacker44433 ай бұрын
I just followed your video and the gauge selector is crooked. I have the tab in the column and it’s just a little off. I can send you pictures on Instagram if that helps any.