Thank you!! Well set up video. Dog made a chew toy out of my original remote. Worked first try. Thanks.

Easy peasy, my Troy Built had 6 screws but still. Thanks for this video.

Nice job, I just clean out the holes with small professional torch orifice cleaners, no need to drill and damage the carb, don't change the engineering just clean! Nice job, and may the force continue to be with you. Ps; my jets fell right out!, o-rings dehydrated and dry. I ordered 1mmx2mmx4mm o-rings on eBay, I heard the other guys say the 1x2.5 are too tight. We'll see. 1mm cross section. 0.040" is about 1mm.

Cool info. But any idea how to get my tv2 21.1 ufh remote to connect to my dish receiver?

This video was amazing and saved me much headache. Thank you.

Español

Can u tell me what the front belt on this is

Trying to code a Samsung dvd player . does the player have to be on 1st ? For both ways of program img?

Welding tip cleaner wires are more flexible and a set comes in enough sizes to fit anything.

So am i right understanding using propane only can effect the carburetor?

Us broke people always having to fix shit.....Rudy's a smart guy, did I ever tell you about the time he flew me in a plane Ps they leave the key in the flower pot😂

Thanks this was helpful 😂😂😂😂

Excellent video. Most of the videos I have seen were for a model that has a different carb so i was glad to see this video.

I was wondering if you can give me the codes for Vizio

Most helpful. Thank you.

Excellant step by step! found the green wire onthe module as problem.

Thanks so much ❤

can you use 2 or 3 tv in the same contoller? and how?

Hi you now how make mars mode for a icom ic-2720?

Maximum batteries in parallel can be 4 batteries not inverter manufacturer asked you to put 4 batteries.

What was the drive belt part number

My generator is running for a few hours then stop it keep doing it and needs more oil 9:42

Please, what is the external microphone connection of this radio? Its connector is 3 pins. 73

Great tip got it on the second try

I have a B&S 450 OHV mower. Is it's possible to change out the prime to start carburetter for the auto choke together with the heat activated unit.

Looked on every website and none of them worked. After rewatching the video a couple of times I got it working thank you!

Thank you for a straight-forward approach to replacing the drive belt!

I have a similar system for my 40 foot Rohn 25G.

Thanks for posting. This mod also works for the V80.

Sansui television 📺

I have a craftsman r1000 it's basically the same as that TB mower. The issue I'm having is it will not shift and only goes slow. I looked at the shifter on the right side of the steering column and linkage. Still can't figure out why it will not shift to a higher speed. Can anyone help me, please?

Two of the screws on the bolts locked up. I wish I saw this video before I tried grinding a notch in the center. It didn't work. Now I know what's under the cover so I can pry it off without causing more work. Thanks.

Legend mate, i wasted a couple of hours with instructions and no good, your way took two minutes thanks heaps Rob

Thanks for the video, programmed it in record time from your video and code list 👍

This is a bit of a shot in the dark, but I noticed you're fairly active with comments so its worth a try. @2:48 do you know where you could possibly find a replacement choke linkage bushing? I followed your instructions and the carb cleanout went phenomenal... however I broke the linkage clip and now cannot find one anywhere for any of these 30 inch riding mowers. Do you happen to know the specs or where I could find a replacement? (My machine is a 2013 Columbia CR30) Thank you so much for the video!!!

Even after replacing the blade mine does not seem to cut grass well at all. Is there a clutch that I should be looking at in the deck or is it possible the belt is just slipping?

My Husqvarna will not move forward or backwards

This did not work on my IC-706MKIIG, do you have any idea why it didn’t work?

i will do this, but with a small thin knife, tnx, 73, Levi in Sweden

7 for Sony

Um unless you completely disassemble the deck hubs and remove the bearing seals then your deck spindles are not greased. It’s a factory designed fail point. The bearings in the hubs are sealed bearings meaning none greasable. They put grease irks in the hub to make you think you greased them. They did this so your deck wears out and you go buy a new deck and or a new complete mower. Most people replace the entire machine instead of just a deck. Don’t believe them just pull a deck hub and see where the grease went. I learned this the hard way.

Thanks once again!

I'm a novice at small engine repairs, but with videos like yours, I've finely figured out how to successfully repair my recoil spring and rope on my 24 yo Tecumseh tiller. I've spent 2 weeks trying to figure out which direction to install the spring, how to keep the spring inside while rewinding it. With your video I realized I didn't need the rope installed until after the spring was working (many hours trying to wrap the spring and rope at the same time). Weird your video didn't show up when I googled this topic, but after about 40 videos, I'm done! So glad, so so glad. Thank you!!

Thanks for the video. What is the code for IP Box MAG254?

Thanks.

Angrej bhi Kya chij hai battery battery 🔋

thanks ez set up

Worked the first time, thank you!

Hi~We have parts that may fit your Honda engine. We're happy to offer you the product completely free of charge in exchange for a video review. Are you interested?

what kind of blade adapter did you get for it?