Where do I download a real version or voda for a 2011 s40

Thank you for a good video! =) Just to clearify - This is not Haldex AWD, it is Viscous? I've got a 2001 V70 AWD and it have the Viscous-system but I can't find any service info of it at all.

So where is the fix??? Dont bother folks ... clickbait

I have a driver bottom seat cushion and cover together to replace mine. do I need to take the whole seat out to replace the driver seat and cover or could I save myself some time without doing it? thanks!

Thanks for doing this man. Helpful! Just finished mine. Even with the aid of my two post lift it’s a PITA

Great video!

How did you wire the electric start?

Thank you for your advice. Today I did it on my Volvo V70 II from 2000 and I found a way without lowering the suspension because there is enough space next to the bushing. I made the tools by myself out from two tubes and welded Rondelles on it. You need only one screw. To press out the axle bushing, an outer sleeve is required that supports itself on the outside of the axle housing and can accommodate the bushing. Inside the small hole, a press-out sleeve is used, which has the same diameter as the bushing. To press in the new bushing from the outside, the sleeve that was previously used on the inside is needed to apply pressure. Additionally, a narrower receiving sleeve is required, which is inserted into the small hole, as the bushing protrudes about 5 mm inward.

Thank you for this video! Im replacing my '15 wheel for one with paddles tomorrow.

thanks for the video

Big thanks!!!!

thanks！from japan

Thanks for the great video! I don't mind where you didn't cut the footage - it helps me get my head in the right place for doing this job. Some notes for later years - I think the compressor bracket alignment jig is not needed 2011 and later - they put bushings/pins in the holes to allow the bracket to self-align. Also, the coupling between the water pump and the PS pump went away in the XC60 (they went to a different ps pump - electric I think), but the XC90's kept the pump and the coupling all the way to the end. I think I have the best of both on my 2012 XC60 - no PS/WP coupling, and alignment jig not needed. I'll tell you for sure tomorrow after I tackle it!

I’m late but thanks for this. My neighbor gave me a 74 9.9 for free today that hadn’t been started in over 20 years. It fired right up with fresh gas but I didn’t see water so I was worried. Couldn’t find the telltale hose, ended up here.

FOCUS!!!

2008 s60 2.5T. I had circuit F malfunction. Replaced throttle body. No more circuit F malfunction. But now have generic p1194. No it isn't fuel trim, they are good. I have 15% throttle at idle, and only 85% wot letting me think it may need calibrating. I tried waiting for the self test but it didnt change anything. As if out of bound, too far from calibration Can this be done with a snap on solus (or other high end scanner) or does it really need the VIDA?

Good job! 0:35 T9 Torx

40:03

Sou do Brasil vou trocar a correia e retentor da polia vvt não tenho ferramenta de trav comondo

Torontonian to our rescue! Thanks for the video. Very helpful.

Or do what I did, give the taken apart remote to your Tetris loving wife, and it goes together in 2 seconds..... And works.

curious... what was the sympton that led you to this mount, noting there are a couple orhers as well ?!

my front O2 sensor reading also stays at 1.00 value. I thought that means its damaged, so replaced the sensor. It is still 1.00. Any idea how to get it fluctuating like it should?

Sir a little gas ⛽️ line first of the season old gas fuel mixture or new clean my suggestion. Andrea Lynne love ❤️ your video

I would buy a 70s Mercury Andrea Lynne for the reason changing plugs checking compression ✔️ expeller and change up the coil .Clean the carb before replacing it

The 70 Mercury's have more power and aggressive sound. Sir

Sir you had it right to start with a little faster than a 9.9 .Andrea Lynne Inouye

Use the old seal to tap the new one in. Helps to distribute pressure easily. Learned that trick changing the tub bearings and seal on my front-load washer.

What symtoms did the car have to make you think it was the mount?

Super helpful. Question: If you were just replacing the high pressure hose, and nothing else, would you still have to lower the subframe in the back? Or would you just lower the front of the subframe, release the tops of the engine mounts, and jack the engine up to make room? I need to replace my hose (sprung a leak), but I don't need to replace anything else, but I can't for the life of me figure out how to get the old hose out, let alone the new one in. Thanks!

after 1 hour of trying found your video, thanks

Could be. You should be able to visually inspect it once you pull out. It’s like a mushroom and if the top has crushed the bottom (say the stem of mushroom) it’s time for a new one. Can’t remember the space on the replacement but there was a healthy gap there.

Hi, great video! I can feel sightseeing vibration when putting into gear with my foot still on the brake. Could this mount cause this kind of issue?

Good video.Are the spacers for the pull start home made? If so can you show them in a short video?Or explain what they are made of and how?

These shields are so stupidly designed! Who in the world decided they shouldn't be able to just fit right over the wheel hub lmao... Absolutely stupid that the only options are either a full wheel assembly rebuild basically or just brake your new shield to replace it

Reedvalve limiters is not same 20 vs 30hp.

Parking brake spring slots rotted out on my shields. This video pretty much seals the deal that I'm just going to delete the parking brake.

For anyone trying to do this there is absolutely no need to cut it I got mine apart easy just use screwdrivers and a hammer and work it apart

In what tab is the oil quality sensor? I wanna reset it after changing the oil for a 2010 S40

Unfortunately this cannot be done 20- 35 .

Is it possible to transfer a 2002 key and fob to the 2003 keyfob?

Links for upgrade parts?

very educative.Thank you . regards

Hey dog hey Doug my name is Tommy I like to know if you got a carburetor for that same model boat that you got there if you do contact me I would love to buy it off of you

Thanks!!

Everything connected. Key in position 2. "Communication tool" under my "Vehicle Profile" tab shows "Not selected." Seems like Vida does not see my DICE. DICE shows Firmware Status with blinking green light (Normal Operation), USB com status not lit, Bluetooth com status lit blue, vehicle interface status static green (DICE test unit connected). Any ideas?

What size is the hole in the middle of the steering wheel?

Where did you get the tool to press out ? Or did you build ? I need one asap dealer wants 1700$

My Grandfather had a 1981 80hp Thunderbolt so I have a soft place in my heart for old mercs.

Do I really need a demo of a well running 9.8 110 merc motor? Mine runs at this time only on 1pot. So how do I test for fire on the other cylinder?