Пікірлер
@octane2099 28 минут бұрын
Who sells those wheels?
@stephenswayze5953 3 сағат бұрын
Love the look of this
@dudernewton4194 Күн бұрын
Megalithic tires from JConsepts
@dudernewton4194 Күн бұрын
Go with 3S smaller batteries. Comp batteries should be just big (heavy) enough to get through a 6 minute run. Rig looks good
@Thatonefoowigz Күн бұрын
What links are you running? Putting together a buggy build and this looks amazing
@Angerhaus Күн бұрын
@@Thatonefoowigz thanks dude! In this video, I got C10/JLU rear links in the front and Deadbolt rear links in the rear.
@d_n_r_rc_racing2449 5 күн бұрын
Hobbysoul on Amazon has wheels with a positive offset.
@finados1595 9 күн бұрын
How did you connect the light bar to the receiver?
@Angerhaus 9 күн бұрын
@@finados1595 I just connected the wires to one of the fog light sockets
@finados1595 9 күн бұрын
@ Are you using an aftermarket receiver?
@Angerhaus 9 күн бұрын
@@finados1595 no, not in this one.
@finados1595 6 күн бұрын
@@AngerhausMaybe mine is different. I don’t have fog light sockets. I only have the port for headlights, break, left and right signals. Nothing else
@Angerhaus 6 күн бұрын
@ Sorry. I was mistaken, I was thinking of my FCX18 converted FJ Cruiser. I have too many little crawlers and this one is from a long time ago. If those are all the sockets available then I probably just spliced into the headlights.
@Gibsonlife573 11 күн бұрын
Another thing brother if you are looking at all for a little bit more wheel speed and to keep low in speed I would check out that mod 5 pitch seems like you're diving deep into the 24th and if you are I would learn about the gearing for the motor and the transmission I run nothing but mod 5 it's a lot easier and the spur don't have as many teeth on it so it normal spur is 55 tooth count of mod 5 is 32 and a mod for is 41 or 42 I can't remember but then you get also play with your opinion and I have found the best setup for that little mini Komodo is a 13 tooth mod for with a mod 4 spur and then run it on 4S and you want to talk about a power horse specially low end speed and killer wheel speed
@Gibsonlife573 11 күн бұрын
Listen if you're running into problems like that get you one of those little shock spacers from injora and put a couple millimeter spacer in between the transmission and skid run your screw up through the bottom of the skid through the spacer and into the transmission and it'll give you just those couple millimeters of wiggle room
@Gibsonlife573 11 күн бұрын
Do you have the little Bend facing down on those links
@Gibsonlife573 11 күн бұрын
And if you want one of the fastest servos on the market definitely check out shift RC their Servo will shake the rig all the way around in a circle if you're running 8.4 and one of the strongest and fastest is the mofo Servo Beast also Holmes Hobby has an amazing Servo that I don't hear a lot of people talk about is super super busy man like the servo horn I'm pretty sure it's a 3 mm screw it's crazy
@Gibsonlife573 11 күн бұрын
Wait a minute you said you're running underdrive plus an additional 33% overdrive that is a lot the most I've ever ran as in my glass and it is 37 percent I run a overdriven transmission turned forward with the motor and then I run 23% in the front end
@Gibsonlife573 11 күн бұрын
Want to eat best shocks on the market blow the Pro-Line out of the water I've had nothing but trouble with the 32s leaking the 50s wasn't so bad but I'm going to tell you now if you run them 36s in the rear and then run to 32 or 34 hot racing up front it makes like a perfect setup or do the 36 up front and do the 40 and the rear from injora I'm hot racing shocks are way better set up than the proline they have real bladders not just a little flat piece of rubber
@Gibsonlife573 11 күн бұрын
You got to look up my 3 flow 9 roller bearing steering link that works amazing he's got all kinds of cool stuff and if you guys run those kinetic like winches all it is a piece of bungee cord he's got some really cool hooks
@ltoyota 11 күн бұрын
Where did you get the Toyota emblem on the front grill?
@Angerhaus 11 күн бұрын
@@ltoyota I think it’s from one of the FMS vehicles. Sorry it’s been a while I don’t remember where everything in my pile of stuff comes from.
@danielschilling4432 11 күн бұрын
What size is the stock wheel hex that comes with the axles? I'm wanting to use rc4wd 1.0 stock bead lock wheels which has a 7mm hex hub.
@Angerhaus 11 күн бұрын
@@danielschilling4432 yep, it’s 7mm hex
@AKlivn 14 күн бұрын
Sweet build!
@김피식-k9n 16 күн бұрын
You are the best builder I know. I have a question about your filming setup. What camera do you use? The footage doesn't seem shaky-do you use a gimbal?
@Angerhaus 16 күн бұрын
@@김피식-k9n haha you are too kind. I am no where near the best. I’m just using my iPhone to film everything. Even the driving footage is just iPhone on a selfie stick. Thank you for watching!
@flat-out 17 күн бұрын
Very nice truck, do you use brushless motor for that? 🤪 Merry Christmas
@Angerhaus 17 күн бұрын
@@flat-out hahaha! Yep and with a bit of FOC too! Merry Christmas, dude!
@ScottGunnel 17 күн бұрын
Thanks for the breakdown! I have a quick question: I have a SafePal wallet with USDT, and I have the seed phrase. (alarm fetch churn bridge exercise tape speak race clerk couch crater letter). How can I transfer them to Binance?
@lgrc6120 17 күн бұрын
Nice build mate
@Angerhaus 17 күн бұрын
@@lgrc6120 thanks!
@TheDreamer562 18 күн бұрын
How did you get the servo to be level? I got the same thing going on with my ccv3. Would I need to change the link setup?
@Angerhaus 17 күн бұрын
@@TheDreamer562 you can rotate the front upper links to get them to the desired position. What I am doing next is actually see if i can further rotate mine to lean the servo back to increase castor. If not, I’d bend them some more.
@RCRoads 18 күн бұрын
Awesome crawler and location. Great job buddy 🫶
@Angerhaus 17 күн бұрын
@@RCRoads appreciate the kind words dude
@doughthejoke8042 19 күн бұрын
What size on the Mazz links? I see 3 different types on the website. Wanting to match this build and needed confirmation. If you could let me know that would be awesome, great build!
@Angerhaus 19 күн бұрын
@@doughthejoke8042 of course man, I got his links for the Gladiator wheelbase. Let me know if there’s anything else I can clarify for you.
@Angerhaus 19 күн бұрын
@@doughthejoke8042 forgot to mention… I dunno how much you wanna match but i already ditched the body. This body is a tad bit too long the nose kept bumping into things.
@doughthejoke8042 19 күн бұрын
@@Angerhaus thank you for the quick response. Getting everything typed up and see it on paper and go from there. I’ll let you know if I have any other questions! Thanks!
@doughthejoke8042 6 күн бұрын
Starting to buy some things today. Noticed the CCV3 TI is out of stock. Is the Carbon fiber one okay or would you highly recommend waiting for the Titanium one to come back in stock. Says the Carbon fiber one is 9.3 gram lighter.
@Angerhaus 5 күн бұрын
@ I honestly don’t think there should be much discernible difference in performance between the two. I got titanium just because I want the rails to be more visible.
@PatrickFugate-qk7ev 19 күн бұрын
Nice..
@michaelreinitz9419 19 күн бұрын
Looks great what color red and silver did you use to paint the panels?
@Angerhaus 19 күн бұрын
@@michaelreinitz9419 thanks! I used Tamiya TS-86 and TS-83
@High_strung_rc 20 күн бұрын
What motor are you running ?
@Angerhaus 20 күн бұрын
@@High_strung_rc Furitek Venom with Lizard Pro ESC
@High_strung_rc 18 күн бұрын
@ ty
@cainclemente6770 20 күн бұрын
What axels are those
@Angerhaus 20 күн бұрын
@@cainclemente6770 MEUS isokinetic axles
@cainclemente6770 20 күн бұрын
What axels are those
@Angerhaus 20 күн бұрын
@@cainclemente6770 MEUS isokinetic axles
@S10W_ass_K150O 21 күн бұрын
Awesome rig
@nolabel2062 22 күн бұрын
What links you using brotha? I love my cheatcode!!!
@Angerhaus 22 күн бұрын
@@nolabel2062 Me too! I was able to snatch up a set of Mazz double bends the same time I bought his chassis.
@cyba888 23 күн бұрын
Stock dead bolt body?
@Angerhaus 22 күн бұрын
@@cyba888 yep
@HermidaF 24 күн бұрын
Are you interested in selling me this project? I honestly don't think I can put this together alone?🥲
@Angerhaus 23 күн бұрын
I'm flattered, but I'm still enjoying this build and I intend on keeping it. I listed all the parts I used in the description. There's really nothing truly unique here, the rig is a mere compilation of those parts. The most difficult thing is probably finding the Mazz chassis in stock 😂. Give it a try, I really think anyone can put together something like this. Feel free to ask if you have any questions.
@Gibsonlife573 11 күн бұрын
You got it man just try and not just that but you're going to learn so much along the way
@Danielxperez14 24 күн бұрын
Looks sick!
@Angerhaus 24 күн бұрын
@@Danielxperez14 😁
@jesselanham1923 25 күн бұрын
Can’t get over this build. I drive a Honda Acty. I need to find an Acty body that would fit on an scx24.
@buddies8757 25 күн бұрын
Bruh, its a RC😅
@Angerhaus 25 күн бұрын
@@jesselanham1923 that’s a cool one too! But I think you’d have to 3D print the body. The 2nd gen is my favourite 👌🏼
@jesselanham1923 26 күн бұрын
Dude. Just found your channel. This build is INSANE.
@Angerhaus 25 күн бұрын
@@jesselanham1923 glad you like it dude! 🙌🏼
@stuartpurdon7190 26 күн бұрын
I so wish the made this with a diesel engine
@Angerhaus 26 күн бұрын
That be the devil's fuel!
@stuartpurdon7190 26 күн бұрын
Love this build I wanted to ask a question or two 1 how much does it cost to do a build like this ? 2 do you use the same chassis between this and the scx 24 hilux build? 3 Do you plan on doing some content on the new HPI hilux in 1/18 ? Ps I love watching your build videos it's therapeutic at this point
@Angerhaus 26 күн бұрын
I appreciate the kind words, Stuart! I've never tallied up my trucks but this one is about $500, not counting the paint and masking tape :). It's one of the more pricey ones. Almost half of it is in the Furitek motor and ESC, which is why I've been experimenting (unsuccessfully) with super cheap brushless systems in some of my recent builds. That Hilux is on RampCrab's LCG chassis. This Deadbolt (which isn't a Deadbolt, it's just a Deadbolt body) is on Mazz's Cheat Code chassis. I'm not a very trendy person, I didn't even bother to watch a review of the Venture18 until you brought it up. Nah.. I don't think I will get it. Not that it's bad, I'm just not into RTR's these days. It does seem like HPI did a great job with it. But I kinda enjoy the process of putting various parts together to create something unique at the end of it. I understand a video of a Venture18 would probably get more views right now but I'm spending my own money and I'd rather spend it on something I like. I am diversifying though, I'm building a couple of TRX4m's right now!😂 I'll likely post a video of one this weekend. It's a TRX4m with a twist. Stay tuned!
@stuartpurdon7190 25 күн бұрын
@@Angerhaus Thank you so much for the awesome response will definitely keep an eye out for new videos !
@SeizedBCG 27 күн бұрын
this deadbolt build goes so hard!
@Angerhaus 27 күн бұрын
😎😎😎
@BlackSmithRC 28 күн бұрын
Looking great bro.
@flat-out 28 күн бұрын
Simply lovely
@mikeearls8158 28 күн бұрын
Outstanding 🙌🏼
@Danielxperez14 29 күн бұрын
when installing the magnets iunto the mounts, did you glue them into the 3d printed piece?
@Angerhaus 29 күн бұрын
@@Danielxperez14 yep, I use E6000 for all my magnets. Let it dry overnight, the magnets won’t come off after that.
@Danielxperez14 29 күн бұрын
@ cool, thank you I’m going to start building mine tomorow, I’ve only done one build and I’m also learning a ton, going to try making my own double bends since the mazz ones sold out
@Angerhaus 29 күн бұрын
@@Danielxperez14 glad you were at least able to snatch up the chassis. Yeah, l got the material to make my own links for my next build which is gonna be based on the NW chassis I told you about before. I’m just waiting for the bender tool and cutter to arrive. Exciting time ahead for us!
@Danielxperez14 29 күн бұрын
@ haha yea and good luck with that I’m just bending my high clearance injoras on a vise for now, I heard good about that chassis I’m excited for your next video man 👍 would love to see a crawl sesh of your crawlers
@Karibouski Ай бұрын
Great review, great build, good video ! Ordered a CCV3 myself and will only get it by the end of the year but I can’t wait to get my hands on it 🤯!!
@Karibouski Ай бұрын
A short note on the transmitter as I’m reaching the end of the video, I’d say fancy and expensive transmitters are mostly useless like you said, I agree, but having at least the ability to adjust end points individually and not just dual rates is pretty great. Main reason why I got a flysky gt5. While not extra cheap, it’s no Noble or 400€ futaba either. Don’t know about you but all my rigs steer further on one side compared to the other so I compensate this with the end point adjustment on the transmitter.
@Angerhaus 29 күн бұрын
@@Karibouski thanks dude! more than a month later, I still think it’s worth the wait!
@Angerhaus 29 күн бұрын
@@Karibouski I was taught for those transmitters without EPA, using a combination of Trim and DR essentially has the same effect. I think it’s worked out well for all my rigs that aren’t paired to my Flysky G7P transmitter (this one has EPA). Even for this isokinetic axle, my DR is at 80%. I do sometimes max it out mid-run to get that last bit steering angle out of the servo though. But yeah I hear what you are saying, it’s not as precise.